Pallet Equipment For Sale

RAIMANN - KM-310, ...Gang (Multi-Blade) Rip Saw12-1/4" Max. width cap., 13-1/2" chain width, 50 HP - 4,200 RPM V-belt driven arbor.Specifications: -- 300 mm (11.8") Max. saw blade dia. with 80 mm (3.15") bore, 65 mm (2.55") dia. arbor. -- Provides 3" max. depth of cut with pressure shoe, 3-1/2" depth of cut without. -- Manual thickness adjustment of upper holddown rolls with indicator scale. -- 6" Throat depth to the right of blade; 7/8" min. strip width, 17-3/4" min. stock length.Equipped with & Features -- "Quickfix Hydro-Quick" Arbor: Multiple Saw blades are mounted on the arbor, they slide up-and-down the arbor into position and lock into place by tightening the end of the arbor; no tools & no spacers required. -- Frequency controlled feed speed of 13 - 110 FPM, 2.2 HP feed drive, chain spikes every 3rd chain link, automatic chain lubrication. -- (4) Sets of top & bottom antikickback fingers. -- Extended infeed with additional bed roll, and adjustable infeed fence. -- Motor load meters and automatic STAR DELTA starting. -- Automatic over thickness shutoff on infeed and 7-1/4" dia. dust hood. -- (3) Laser lights.

RAIMANN KM 310 1M - Movable Blade Gang Rip Saw; 12-1/4" Max. width cap.; 13-1/2" chain width; with 25" width clearance,Specifications: -- 50 HP - 4,200 RPM V-belt drive arbor with (1) movable and (2) fixed blade; shifting blades positioned from operator controls. -- As the computer or operator moves blade, laser light follows; fixed saw blade with "Quick Fix" hydro-arbor is mounted on an individual collar that slides up-and-down the arbor into position, then locks into place by tightening end of arbor; no tools & no spacers required.Equipped with: -- Blade capacity 11" to 14.1" (280 -380 mm) Dia. saw blades, 65 mm (2-1/2" dia.) arbor, 4-1/4" max. depth of cut, 17-3/4" centers between upper holddown rollers (phenolic pressure holddown shoe plate included); 3/4" min. strip width, 19-1/2" min. stock length. -- Variable feed speed from 13 - 115 FPM, feed drive 2.2 HP motor, provision for chain spikes every 3rd chain link, automatic chain lubrication. -- (2) Sets of top & bottom anti-kickback fingers, extended infeed with additional bed roll, and adjustable infeed fence.Complete with: -- Automatic over-thickness shutoff on infeed. -- (4) Laser Lights. -- Automatic STAR-DELTA starting. -- "ProfiCut 1" PLC Controls. -- 8" Dia. dust hood. -- Includes with approx. (9) blades.Dimensions: 85" x 56" x 73" H. Weight: 3,750 Lbs.Note: Stated condition reflects that the chain is worn and per owner "?Chain should be replaced."

Rayco Edge Pallet Nailing Machine S/N E201550 230V 3PH 15A Fused Amps w/Stacker

Runs well Extra nail guns included

220 V 3 PH Good Working Condition Up to 50" x 50"

2007 | 460v 3 Phase | 300-400 pallets per shift

Rayco Edge Pallet Nailer (3) Nail Guns Stacker

Rayco Edge 480 Volt with Reducer to 240 Volt 3 Stringer S/N 98040 Out and Ready to Ship.

Rayco Edge Pallet Nailer Used Regularly Available Immediately

2005 | 4 stringer 2 or 4-way 60”x60” | 460V 3PH

ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4” elevation and drops down to place the lumber onto the Transfer Chains at 42” elevation. 66” wide rolls are 2-12” diameter steel rolls, snap in style on 12” centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1”.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6” CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42” +/- 1”. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5” diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42” +/- 1” -- Stock width 2” to 9” -- Stock Thickness 1/4” to 4” -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50” long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2” bore air cylinders actuate the pinch rolls -- With 3/4” fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and

2009 Rotochopper E256 Grinder/Shredder | 200 HP electric rotor drive motor | 50 electric hydraulics motor |

Salem Top Arbor Gang Rip Saw 8" Capacity 300 HP Motor Blades: Approx 30 Sharpened carbide blades still have wax, and 30 that need to be sharpened Includes: All electrical, misc blades, guides, spacers Included: Milling machine and Babbitt pot System needs a 10 HP feed motor

The SALVADOR SUPERANGLE 600 is a pusher chop saw that provides complete chop to length and optimization of wood strips including the elimination of defects. --The infeed is made of heavy-duty steel frame with working height of 1000mm (39") from floor level. Safety is provided by a light curtain. -- The pusher slides on double hardened rails. --The reading operation uses two sensors, one for the overall length and the other to read the crayon marks. --The transmission of power from the motor to the carriage is accomplished by a steel reinforced toothed belt 50mm wide. --The part is held in place by two aligners before and after the blade insuring a square cut. --The saw box area is enclosed by interlocking steel cover with a large widow for clear view. The saw travels through an aluminum table insert that can be easily changed as needed. High efficiency motor IE3 rating helps to keep power consumption to the minimum. --Technology - The operating software is a customized Windows based program designed to be intuitive and specially designed for optimization of the wood. There is a large 19" monitor at operator eye level. The PC is set up with SSD double hard drive with the second being a clone to have an ready to go back up already in the machine. Cut lists can be uploaded remotely by network connection or flash drive. Chop length optimization can be set for minimum waste priorities. The optimizer supports defecting crayons as well as up to (5) grade qualities. --Electronics, the multi tap transformer steps down higher voltages , 460 - 600 to the voltage requited by the machine. --SP 15 Magnetic Strip Measurement, technology improves positioning from basic encoder standards to absolute measurement's of +/- 0.1mm. -- Outfeed with 0 degree belt and 1 pc double ejector. For applications of many work pieces cut at angles its best to eject the work pieces together with one large rack and pinion ejector. Work pieces are pulled from the saw on an out feed belt. Once the parts are clear of the saw the large ejector manages all cuts in one push onto the steel table for collection. WORKING CAPACITY:Maximum board length before cutting 5100mm (16')Minimum board length before cutting 500mm (19.6")TECHNICAL SPECIFICATIONSMain saw power 15 HPSaw blade specifications SA600 Max 600mm dia. bore 35mmMaximum pusher reading speed 60M/min (200'/min)Maximum pusher pushing speed 60M/min (200'/min)CUTTING CROSS SECTION #9679 0°: 100mm x 360mm / 160mm x 310mm #9679 +/- 45°: 100mm x 260mm / 160mm / 220mm #9679 +/- 70°: 100mm x 120mm / 160mm x 100mmMinimum 15mm x 30mmNumber of cuts within last 40mm of board One (1)Maximum workpiece weight 110 kgs (242 lbs)Power requirements #9679 11 kW #9679 Primary supply voltages 220/380/420/440/460/480/560/580/600VPneumatic requirements #9679 Compressed air supply 600 - 800 kPa (6-8 bar) #9679 Maximum air consumption 300 Nl/minDust extraction: #9679 intake diameter 160mm upper / 120mm lower #9679 Extraction system collection

5HP motor on 10" blades..1HP on feed..1/2" to 2" board thickness..22" to 60" length of cut..Available in three phase or single phase. Sawmill Supplies & Equipment is proud to be a small town family owned business. Owned by the Morgans and Located in Sarepta, La. Still building the ORIGINAL Low Profile Band Resaw. Need parts for your Morgan equipment? Give us a call. Tell us what you want and we build it..... the RIGHT way! Standard and Custom equipment available.

Manufactured by the Morgan family. 3 phase, single phase or line shaft. Hopper feed w/adjustable fence. Feed rate - Adjustable 120-400 FPM. Capaity 3/8" to 3 1/2"H x 6 1/2"W. Two nylon or steel brushes. The video shows a four head Morgan Band Resaws in-line with a Morgan Board Deduster.