Woodworking Equipment For Sale
1738 Results Found
SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL/CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding.Panel Capacity: Min. Panel width 60 mm (2.375"); Min Panel length 140 mm (5.5").Min./max. Panel thickness 8 - 54 mm (0.375" - 2.125"); Minimum distance between panels 508 mm (20").Feed speed 36 and 52 FPM (2.5 HP feed motor) -- Equipped With:Adjustable In-feed Fence:Manually pre-set with digital indicator, pneumatic in/out positioning. 1-Coil feeder: For banding up to 3mm thick with a 3 mm guillotine.Gluing Station:For EVA (Hot Melt) with Quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. 8-10 Min.Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. Includes "Strip Feed Magazine" -- Workstations:End Trimming Station: "K-SEL 2" Front & rear 0.5 HP, 12,000 RPM motor mounted on THK guides, swivels 0° - 15°, rapid set up between straight and angled cutting with the automatic swivel cylinder. Top & Bottom Trimming Unit: 2 x 1.0 HP - 12.000 RPM Motors capable of tilting 0 to 25 degrees with copy wheels. Pneumatic positioning for (3) settings, flush/bevel/radius trimming via precision digital indicators to go from 3 mm PVC to thin tape through the controller for quick setup.Two Motor Corner Rounding:(2) 0.80 HP independent motors that slide on THK guides. The features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations Top & Bottom Profile Scraping Unit: "RAS/K" profile scrape station for 3 mm PVC with pneumatic positioning, with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: "STARTOUCH" Controller with 12" touchscreen display, capable of storing 100 programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors. Process statistics data, ie. No. of pieces/edges, and track feeding. -- Features & Complete With:1 x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units;Manual adjustable hold-down pressure beam;Full sound enclosure cover and outboard panel support.Adjustable side support. Replaceable track pads. Digital inverter for electronic motor braking Acoustical safety enclosure.Dust Collection: Working units are individually ported on the top of the safety enclosure for maximum efficiency.Suitable Transformer for 230V to 600V, 3 Ph. Actual model is SCM OLIMPIC K 600 T-ERL.
$ 15,000
SCM TECH Z 30 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications:Working Field "X" axis 120" (3,050 mm); "Y" axis 52.7" (1,340 mm) for routing & 44" (1,118 mm) for boring; "Z" axis stroke 7.8" (200 mm); max. material thickness 3.9" (100 mm). -- Positioning Speed:"X" & "Y" Axes are 197 FPM (60 MPM); "Z" axis is 72 FPM (22 MPM).Axes positioning by: AC Brushless motors and YASKAWA drives; high precision ball screw drive system in "X", "Y". "Z" Axes;All axes ride on prismatic guideways & sliding blocks. -- Worktable:(6) "TV" Tubeless mobile support rails, (2) vacuum pods per rail; (4) pneumatic lifter rails for heavy panels.(6) Pneumatic pop-up backstops, (6) pneumatic pop-up front stops; (2) pneumatic pop-up side stops.LED Display positioning assistance for the support rails & vacuum pods; (2) independent working fields. -- Boring Head:3 HP (2.2 kW) motor - 4,000 RPM; (15) independent vertical spindles: (8) Spindles in "X" & (7) spindles in "Y".(6) Horizontal spindles (2 + 2) in "X" & (1 + 1) in "Y-axis".(1) X-axis grooving saw with 100 mm dia. blade - 6,000 RPM. -- Machining:(1) 10 HP (7.5 kW) Electro-spindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM, max. torque achieved at 12,000 RPM.Static inverter for stepless speed & rapid shutdown rotation.(1) 6-Position ATC tool plate mounted on the on the machine for "on the fly" ATC; max. tool weight is 8 kG (17.6 Lbs). -- Operator & Machine Control:PC Front-End with: SCM "UNIVERSAL K2" + "Xilog Plus" + Windows "XP" Pro Operating System; 15" CRT color display, CELERON 2 GHz processor, enclosed in air-conditioned cabinet. -- Complete with:(1) 100 m³/Hr Vacuum Pump; automatic lubrication system; "BUMP STOP" safety system. -- Actual Model is SCM TECH Z30 R6
$ 7,700
SCM - S520 E, ...Planer Specifications: -- 20" Width cap., 9 HP main motor - 4-3/4" dia. 4-knife TERSA cutterhead at 4,500 RPM. -- 1/8" - 9-1/4" Powered opening with digital readout for fine adjustment; max. depth of cut 5/16"; 10" min. length of workpiece. -- (4) Feed speeds: 20 - 33 - 43 & 56 FPM; table size 20-3/4" x 39".Equipped with: -- Chipbreaker, sectional grooved infeed & solid outfeed rollers, (2) adjustable bed rollers. -- Complete with: Magnetic starter & shaving hood.
$ 14,500
SCM SANDYA 3-RCS-95 Wide Belt Sander 9 ( 2 ) Heads36" width cap. Drum, PlatenHead Configuration1st Head : Contact Drum2nd Head : Combination HeadSpecifications: -- 1st Head: Contact roll, 4-3/4" dia.; -- 2nd Head: Combination head, with rubber covered contact roll, 4-3/4" and 2" wide finishing platen -- Both contact rolls & platen with cam height adjustments. -- 30 HP Motor driving both heads;Equipped with & Features -- 37" x 75" abrasive belts -- Electronic tracking and pneumatic belt tensioning. -- Infeed & outfeed rolls, -- Dual feed speed of 15 & 30 FPM, -- 0.5 HP feed drive -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout, -- 0" - 6-1/4" opening. -- Motor load meters, -- Infeed & outfeed conveyor roller extensions, (2) 5" dust ports.
$ 10,500
SCMI SANDYA 3 Wide Belt Sander, (2) Heads37" Width cap. Drum, and Combination HeadHead Configuration:1st Head: 4" Dia. Steel Contact Drum 2nd Head: Combination head, rubber-covered contact roll, 4" dia. and 2" wide finishing platenSpecifications: -- Air jump platen with timers to control raise & lower of platen on leading and trailing panel edge. -- 30 HP motor driving both heads. -- 37" x 75" Abrasive belts with electronic tracking and pneumatic belt tensioning.Feed System; -- Infeed & outfeed spring loaded holddown rolls. -- Dual feed speed 15 & 30 FPM, 0.5 HP feed drive. -- 0 - 6" Motorized thickness opening via (4) precision conveyor bed jacks with LED readout.Equipped with & Features: -- Automatic part thickness adjustment. -- Motor load meters -- 21" infeed & outfeed conveyors each with (2) rubber-covered rolls -- (2) 5" Dust ports.Note from the seller: Lightly used machine in a two-man shop, primarily sanded our face frames for kitchen jobs, which amounted to a couple sets a month. works well, had an opportunity to purchase a bigger sander so this one is redundant.
$ 29,500
SCM - Concept 2000, ...Double End Tenoner.Double End Tenoner with: Jump scoring, Hogging, Shaping with stacked tooling. -- 122" Opening cap., motorized opening with keypad entry & LED readout, 12" infeed chain area in front of holddowns. -- 0" - 4" Motorized thickness opening with mechanical digital readout. -- 6" Min. width, 2-post machine. Each side equipped with: -- 1st Station: Jump scoring. -- 2nd Station: Hogging unit. -- 3rd Station: Coping head with stacked tooling capacity (manually operated). -- 4.5 HP Drive for 10 - 60 FPM variable feed speed. -- Chain dogs on 15-3/4" centers, rubber top nonmarring chain pads. -- Heavy-Duty chain links with: Needle bearings, automatic oil mist chain oiler, automatic brake on feed motor with emergency stop.Complete with: -- Upper driven holddowns with: Continuous feed belts; feed beams can be disengaged for conventional part feeding in front of dogs. -- Mobile remote control for setup; dual lead screw for traversing beam; exhaust hoods on all heads.Note: Tear down and loading not included.
Call for Price
Call for Price
Belt size 43” x 85” (2) six inch dust ports 1st head 24 HP 230 2nd head 18 HP 230 Fiest head contact drum Second head combination with finish platen Feed rate 3 to 68 feet per minute Weight 4550 lbs 230 volt 3-phase
Call for Price
Call for Price
$ 7,900
Call for Price
Motor Horsepower 12 HP Working Width 630mm (24 3/4”) Working Height 3 – 300mm (1/8” – 11 3/4”) Max. Depth of Cut 8mm (5/16") Minimum Length of Stock 260mm (10 1/4”) Cutter Head Diameter 120mm (4 3/4") RPM 4500 No. of knives 105 Knife Dimensions 15mm x 15mm x 2.5mm Table Size 630mm x 1000mm (24.75” x 39.4”) Feed Speeds (Variable) 4 - 20 m/min (13 - 65 FPM) Infeed Roller Steel sectional, power driven Outfeed Roller (x 2) Rubber, power driven Dust Hood Diameter 150mm Noise Level (dB) 70 Overall Dimensions (L,W,H) 51" x 40" x 45” Shipping Weight 1230kg (2,710 lbs) Net Weight 1155 kg (2,550 lbs) Electrical Requirements 45 amps @ 230 volts Dust Extraction 980 CFM
Call for Price
Working Areas: X-Y Axes Dimensions (Depending on Machine Configuration) (Mm): 5510×1320 Axes: Vectorial Speed X-y Axes M/min: 56 (Prospace), 78 (Prospeed) Z Axis Panel Passage mm: 180 Routing Unit: Motor Power (Max.) Kw (Hp): 15 (20,5) Rotation Speed (Max.) Rpm: 24000 Available Tools on Tool Changer (Max.) Places: 24 Spindle: HSK63 Machine has a drill block that was never used. Still under power but ready to move.
Call for Price
Call for Price
Call for Price
Call for Price
SCMI S630 Planer Capacity 24” x approx. 10” Straight 4-knife cutterhead Sectional chipbreaker and sectional infeed roller Cutterhead motor: 12HP, 230v (currently wired)/460v, 3PH 39” long bed with (2) idler rollers 2 rubber coated outfeed rollers with air assist Motorized raise/lower Includes manuals Solid machine. Currently replacing all bearing and thoroughly cleaning down to the bolts. Operating Instructions, Parts manual, wiring diagram included. Extra set of knives included. Weighs 2000lbs+
Call for Price
Working height 120 mm working width 240 mm feed speed 6-36 fpm 6’6” straightening infeed
Call for Price
Call for Price
35 spindles (vertical/horizontal) 32mn spacing left/right fences quick release chucks 2800 rpm spindle speed 5 HP 3 Phase