• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
8 Results Found for Planer Viewing 1 - 8 of 8 results
RECENTLY ADDED
STANDARD LISTINGS
Newman M-55 Planer/Moulder Infeed Table 15' S/N 13857
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
30" width with a 6" max. & 3/8" min. thickness cap., shortest stock 46" (not butted). -- Equipped with: 75 HP - 3,600 RPM Direct drive motor to top head, 40 HP - 3,600 RPM direct drive motor to bottom head, both heads with NEWMAN 8-knife "Quiet Cut" helical head (7" cutting circle) with "a good bit of carbide left on the knives" (without knife griner and jointer). Sectional top chipbreaker with 3" wide hardened steel sections. -- 25 HP Hydraulic power unit for variable feed speed of 80 - 300 FPM with digital readout, (1) top infeed and (1) top outfeed powered tire roll assembly, each consisting of (4) 16" dia. pneumatic tires allowing up to 1-1/2" independent yield, additionally bottom infeed and single outfeed idle rolls, outfeed bottom roll with scraper; motorized thickness adjustment, 1 HP motor. -- Complete with: Wear strip for rear platen, chrome plated insert for front platen, infeed table, cutterhead brakes, and dust hoods. -- Machine includes a 20' x 30" heavy-duty powered infeed belt conveyor, a 7' x 30" outfeed roller conveyor, and a 4' x 8' scissor-lift. _ NOTE: This Planer needs a "going through" with regards to general surface rust etc.. It is currently under power and can be inspected cutting wood. However, as the pictures verify, the machine has not been in operation for some time.
Equipment Location:SOUTHEAST
Jeff Terrill
800-374-5009 ext:349
NEWMAN WHITNEY S 282 Top & Bottom Surface Planer;18" x 6" Max. capacity, Coupled Drive Fixed Bed Double Surfacer.Specifications: -- 40 HP - 3,600 RPM top head OPD motor, 25 HP - 3,600 RPM bottom head ODP motor. -- 6-Knife Newman "QuietCut" Sprial Carbide Cutterheads on the top and bottom including appropriate grinding equipment for both heads.Feedworks consisting of: -- (4) Feed rolls, top infeed roll and top outfeed roll each with (3) pneumatic tires mounted on steel shafts; top roll yokes are pivoted from frame allowing stock variations and quick roll raising; (2) idle bottom rolls mounted on ball bearings. -- Infeed Works consists of: (2) Pivot mounted top feed rolls each with three pneumatic tires (three on infeed and three on outfee) that are 16" in dia. with over 1-1/2" independent yield. -- (1) 6" Dia. steel idle infeed bottom roll and (1) 12" dia. steel idle outfeed bottom roll. -- With infinitely variable feed from self-contained hydraulic drive system; 15-HP hydraulic pump motor, feed speeds 40 - 150 FPM.Equipped with: -- Sectional top head chipbreaker with 3" wide sections, with hardened steel toe pieces. -- Cutterhead brakes, dust hoods, outfeed bottom roll equipped with roll scraper. -- Freestanding standard control panel equipped with full voltage starters for motors and fuses for line protection.Machine condition " As Taken From Service"
Equipment Location:MID ATLANTIC
Jeff Terrill
800-374-5009 ext:349
NEWMAN/WHITNEY S 382 HD TOP & BOTTOM Roughing Planer with Transfer Conveyors: 30" Width with a 6" max. & 3/8" min. thickness cap., shortest stock 46" (not butted). Equipped with: -- 75 HP - 3,600 RPM Direct drive motor to top head, -- 40 HP - 3,600 RPM direct drive motor to bottom head, both heads with NEWMAN Straight knife head (7" cutting circle) . -- Sectional top chipbreaker with 3" wide hardened steel sections. -- 15 HP Hydraulic power unit for variable feed speed of 80 - 300 FPM --Top head pressure bar-manual release Double set tire infeed rollers, each consisting of (5) 16" dia. pneumatic tires allowing up to 1-1/2" independent yield, additionally bottom infeed and (5) outfeed rolls, outfeed bottom roll with scraper; motorized thickness adjustment, 1 HP motor.Infeed and Outfeed System -- (1) Deck conveyor with (3) chains, 11' wide X 27' long -- (1) Infeed belt conveyor 30" wide X 20' long -- (1) Outfeed belt conveyor 30" wide X 24' long -- (1) Finish product deck conveyor (3) chains, 11' wide X 27' longNote: This machine has new bearings, new feed tire, new cutter head
Equipment Location:EASTERN CDN
Jeff Terrill
800-374-5009 ext:349
NEWMAN WHITNEY S 282 Top & Bottom Surface Planer:18" x 6" Max. capacity, Coupled Drive Fixed Bed Double Surfacer.Specifications: -- 40 HP - 3,600 RPM top head OPD motor, 25 HP - 3,600 RPM bottom head ODP motor. -- 6-Knife Newman "QuietCut" Sprial Carbide Cutterheads on the top and bottom including appropriate grinding equipment for both heads.Feedworks consisting of: -- (4) Feed rolls, top infeed roll and top outfeed roll each with (3) pneumatic tires mounted on steel shafts; top roll yokes are pivoted from frame allowing stock variations and quick roll raising; (2) idle bottom rolls mounted on ball bearings. -- Infeed Works consists of: (2) Pivot mounted top feed rolls each with three pneumatic tires (three on infeed and three on outfee) that are 16" in dia. with over 1-1/2" independent yield. -- (1) 6" Dia. steel idle infeed bottom roll and (1) 12" dia. steel idle outfeed bottom roll. -- With infinitely variable feed from self-contained hydraulic drive system; 15-HP hydraulic pump motor, feed speeds 40 - 150 FPM.Equipped with: -- Sectional top head chipbreaker with 3" wide sections, with hardened steel toe pieces. -- Cutterhead brakes, dust hoods, outfeed bottom roll equipped with roll scraper. -- Freestanding standard control panel equipped with full voltage starters for motors and fuses for line protection.NOTE: Price includes a Southworth 42" x 60" x 6,000 lbs. Scissor Lift Table for incoming lumber units, Infeed Belt Conveyor, and a in 12' X 12' x 5-chain outfeed chain deck powered by a 10 HP fixed speed motor. -- Machine offered" As Taken From Service"
Equipment Location:SOUTHEAST
Jeff Terrill
800-374-5009 ext:349
Newman EPR-24 Planer
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
NEWMAN WHITNEY S 282 Top & Bottom Surface Planer;Specifications: -- 18" x 6" Max. capacity, Coupled Drive Fixed Bed Double Surfacer with 50 HP - 3,600 RPM top head OPD motor, 40 HP - 3,600 RPM bottom head ODP motor. -- 6-Knife Newman "QuietCut" Sprial Carbide Cutterheads on the top and bottom including appropriate grinding equipment for both heads.Feedworks consisting of: -- (4) Feed rolls, top infeed roll and top outfeed roll each with (3) pneumatic tires mounted on steel shafts; top roll yokes are pivoted from frame allowing stock variations and quick roll raising; (2) idle bottom rolls mounted on ball bearings. -- Infeed Works consists of (2) Pivot mounted top feed rolls each with three pneumatic tires (three on infeed and three on outfee) that are 16" in dia. with over 1-1/2" independent yield. -- (1) 6" Dia. steel idle infeed bottom roll and (1) 12" dia. steel idle outfeed bottom roll. -- With infinitely variable feed from self-contained hydraulic drive system; 20-HP hydraulic pump motor, feed speeds 40 - 150 FPM.Equipped with: -- Sectional top head chipbreaker with 3" wide sections, with hardened steel toe pieces. -- Cutterhead brakes -- Dust hoods -- Outfeed bottom roll equipped with roll scraper. -- Freestanding standard control panel equipped with full voltage starters for motors and fuses for line protection -- Wiring to National Electric Code -- Hardened steel toe pieces -- Infeed table with kickback fingers -- Controls for hydraulic tank -- Auto Cut ControlMAKE OFFER
Equipment Location:MID ATLANTIC
Jeff Terrill
800-374-5009 ext:349
High Production Top & Bottom Planer; --30" width with a 6" max. & 3/8" min. thickness cap., shortest stock 46" (not butted). -- Equipped with: 75 HP - 3,600 RPM Direct drive motor to top head, 40 HP - 3,600 RPM direct drive motor to bottom head, both heads with NEWMAN 8-knife "Quiet Cut" helical head (7" cutting circle) with "a good bit of carbide left on the knives" (without knife griner and jointer). Sectional top chipbreaker with 3" wide hardened steel sections. -- 25 HP Hydraulic power unit for variable feed speed of 80 - 300 FPM with digital readout, (1) top infeed and (1) top outfeed powered tire roll assembly, each consisting of (4) 16" dia. pneumatic tires allowing up to 1-1/2" independent yield, additionally bottom infeed and single outfeed idle rolls, outfeed bottom roll with scraper; motorized thickness adjustment, 1 HP motor. -- Complete with: Wear strip for rear platen, chrome plated insert for front platen, infeed table, cutterhead brakes, and dust hoods. -- NOTE: This Planer is said to have 1,800 hours of run time, it has been sitting for quite some time and a complete maintenance service will be required before putting it back into production.
Equipment Location:MIDWEST
Jeff Terrill
800-374-5009 ext:349