Woodworking Equipment For Sale
1446 Results Found
BUTFERING OPTIMAT SBC 311 RCE Wide Belt Sander (3) Heads43" Width cap. Drum, Combination Head, Platen.Head Configuration:1st Head: Steel contact roll, 8" dia., 25 HP motor.2nd Head: Combination Head with Rubber covered contact roll, Segmented Platen/Pad, 20 HP Motor.3rd Head: Segmented Platen/Pad, 17 HP Motor.Specifications: -- 43" x 75" Abrasive belts, electronic abrasive belt tracking, -- Conveyor belt feed with variable feed speed from 8 - 43 FPM. -- Automatic conveyor belt tracking, infeed & outfeed spring loaded rubber covered holddown rolls. -- 1/8" - 5-1/2" Motorized thickness adjustment with LED readout..Equipped with & Features: --Vacuum Bed -- Infeed panel "over-thickness" sensor -- Infeed & outfeed emergency stops, safety interlocks on all doors. -- Motor load meters, and main motor electronic brakes
BUTFERING Profiline SUR 313 RRR Bottom Wide Belt Sander with Powered Infeed & Connect to Top Sander (...see SX-012684 OPTIMAT SCO 413 RRRR Top Head Wide) Bottom 3-Head, 53" Width Capacity Wide Belt SanderHead Configuration: -- 1st Head: Steel Contact Roll, 240 mm (9-1/2") dia., 22 kW (30 HP) motor; -- 2nd Head: Rubber covered Contact Roll, 65 Shore, 320 mm (12-1/2") dia., 22 kW (30 HP) motor; Rotation with or against feed direction; -- 3rd Head: Rubber covered Contact Roll, 55 Shore, 320 mm (12-1/2") dia., 18.5 kW (25 HP) motor; Rotation with or against feed direction.Features & Specifications: -- Out-feed Rotary Panel cleaning brush with abrasive grit, 5.5 kW (7.5 HP) motor; -- 950 mm (37") Section of free standing power driven infeed roller track; -- 54" x 103" Abrasive belts, electronic abrasive belt tracking, and all heads with servo driven grit compensation and motorized positioning; Abrasive belt Air-jet blowers on all heads. -- Vacuum conveyor belt feed with variable feed speed 5 - 25 m/Min (16-1/2 - 82 FPM), automatic conveyor belt tracking, infeed & outfeed spring loaded rubberized hold-down rollers, outfeed extension for linking to transfer conveyor, connecting Bottom head to Top head Sander. -- Constant passline of 900 mm (35-1/2") by adjustment upper machine frame via (4) large dia. threaded spindles. -- Tie-in conveyor to connect to Top-Head Sander, 1,500 mm (59"), 5 - 25 m/Min (16-1/2" - 82 FPM), synchronized with machine bed conveyor speed. -- Color touch screen control with 1,000 programs, 1/8" - 5-1/2" motorized thickness adjustment, "quick-set" automatic thickness adjustment with LED readout; infeed panel "over-thickness" sensor.Complete with: -- Infeed & outfeed emergency stops; safety interlocks on all doors; roller infeed conveyor extension; motor load meters and electronic brakes for all sanding head motors. -- Operator and Maintenance manuals (in Spanish); spare parts drawings, spare parts list, and wiring diagram.NOTE: -- BUTFERING "PROFILINE SUR" Bottom Sander and "OPTIMAT SCO" Top Sander are being offered as a Complete System/Line with Infeed and Transfer Connect; one common Control for both machines to operate as line. Copy of original quote with detailed specifications is available upon request.Asking Price with this "SX-012681" listing is for the Bottom Head Sander only - Open to reasonable offers.
BUTFERING OPTIMAT SCO 413 RRRR Top Head Wide Belt Sander (...part of line with SX-012681 Profiline 3-Head Bottom Sander)Top 4-Head, 53" Width Capacity Wide Belt Sander with (4) Drums (Rollers).Head Configuration: -- 1st Head: Steel Contact Roll, 240 mm (9-1/2") dia., 22 kW (30 HP) motor. -- 2nd Head: Rubber covered Contact Roll, 85 Shore, 240 mm (9-1/2") dia., 22 kW (30 HP) motor. -- 3rd Head: Rubber covered Contact Roll, 65 Shore, 320 mm (12-1/2") dia., 22 kW (30 HP) motor; Rotation with or against feed direction. -- 4th Head: Rubber covered Contact Roll, 35 Shore, 320 mm (12-1/2") dia., 18.5 kW (25 HP) motor. -- All Heads with servo positioning of Contact Roller via precision motor to 1/100 mm, with possibility to store different values in the Terminal.Features & Specifications: -- Out-feed Rotary Panel cleaning brush with abrasive grit, 5.5 kW (7.5 HP) motor. 950 mm (37") Section of free standing power driven infeed roller track. 54" x 103" Abrasive belts, electronic abrasive belt tracking, and all heads with servo driven grit compensation and motorized positioning. Abrasive belt Air-jet blowers on all heads. Automatic head locking for fast abrasive belt change. -- Vacuum conveyor belt feed with variable feed speed 5 - 25 m/Min (16-1/2 - 82 FPM), automatic conveyor belt tracking, infeed & outfeed spring loaded rubberized hold-down rollers. -- Constant passline of 900 mm (35-1/2") by adjustment upper machine frame via (4) large dia. threaded spindles. -- Color touch screen control with 1,000 programs, 1/8" - 5-1/2" motorized thickness adjustment, "quick-set" automatic thickness adjustment with LED readout; infeed panel "over-thickness" sensor.Complete with: -- Infeed & outfeed emergency stops, safety interlocks on all doors, roller infeed conveyor extension, motor load meters and electronic brakes for all sanding head motors. -- Operator and Maintenance manuals (in Spanish); spare parts drawings, spare parts list, and wiring diagram.NOTE: -- BUTFERING "PROFILINE SUR" Bottom Sander and "OPTIMAT SCO" Top Sander [SX-012681] are being offered as a Complete System/Line with Infeed and Transfer Connect; one common Control for both machines to operate as line. - Copy of original quote with detailed specifications is available upon request.Asking Price with this "SX-012684" listing is for the Top Head Sa only - Open to reasonable offers.
BUTFERING CLASSIC 213-CE Wide Belt Sander (2) Heads --53" cap. Excellent for solid wood, veneer & sanding of lacquer, fill coats or de-nibbing. - Equipped with: (2) Combination heads with segmented platens, and (1) panel cleaning brush. --Head Configuration: --1st Head: Combination head with rubber covered contact roll (85 Shore) and electronically controlled segmented "CPS" platen, (52) 25 mm wide segments pneumatically controlled with variable edge pressure, variable speed from 30 - 60 FPS, segments conform to the panel shape with variable edge pressure control to reduce sand throughs. --25 HP Motor, 3 abrasive belt speeds; 54" x 103" abrasive belt with electronic tracking, air blast belt cleaning. --2nd Head:CPSSegmented polishing platten, (52) 25 mm wide segments pneumatically controlled with variable edge pressure, variable speed from 5 - 40 FPS. -- 20 HP Motor, 3 abrasive belt speeds; 54" x 103" abrasive belt with electronic tracking, air blast belt cleaning. --3rd Station: Outfeed rotary panel cleaning brush, 5 HP drive motor. --Equipped with & Features --PLC Controller: "TE1" with 50 Programable addresses, PLC control of segmented sanding pressure. -- Conveyor feed drive: Electronic variable feed speed from 8 - 42 FPM, vacuum bed assembly, 4.7 HP vacuum suction fan, conveyor infeed belt cleaning, constant conveyor bed assembly pass-line @ 35.5"(conveyor remains at a constant height). --Feed motor 2.3 HP --Infeed and outfeed spring-loaded holddown rollers on all heads, 0" - 2" motorized part thickness opening, automatic conveyor belt tracking and tensioning.
BUTFERING CLASSIC -313-QCE Wide Belt Sander (4) Heads; 53" Width capacity, Crossbelt, Combination Head, Segmented Platen, Panel Cleaning Brush.Head Configuration: 1st Head: -- Cross belt, 2-speed abrasive belt. -- 9 or 18 MPS (30 + 60 FPS), 24 HP motor. -- Pneumatic belt cleaning, Inner "Chevron Belt" with independent tensioning. -- CPS50 Segment control, 26 - 50 mm segments with variable edge pressure.2nd Head: -- Combination head, contact roller with segmented pad. -- Rubber covered contact roller 85 shore (grooved) 5-1/2" dia., 2-speed abrasive belt drive, 9 + 18 MPS (30 + 60 FPS) 24 HP motor. -- Pneumatic belt cleaning. -- CPS50 Segment Control, 26 - 50 mm segments with variable edge pressure.3rd Head: -- Segmented Pad. Electronic variable speed belt drive, 2.0 -18.0 MPS (6.6 - 59.1 FPS), 20 HP motor. -- Rubberized pressure rolls (throughout machine), Pneumatic belt cleaning. -- Additional sanding insert for sealer sanding. -- Bi-Directional belt drive included. -- CPS50 Segment Control, 26 - 50 mm segments with variable edge pressure.4th Head: -- Panel cleaning brush at Outfeed, 1.2 HP motor.Feed System: -- Constant Pass Line. -- Electronic variable speed infeed 8 - 42 FPM. -- Roller infeed extension. -- Vacuum infeed, internally mounted 8.5 HP. -- Vacuum bed two-sections in through feed direction.Specifications & Equipped with: -- Crossbelt size 6" x 185". -- Head 2 - 3 belt size 52" x 103". -- Machine working width 53". -- Automatic pneumatic belt tracking. -- Automatic belt tensioning. -- Automatic infeed belt tracking. -- Automatic infeed belt tensioning. -- PLC CONTROLLER, with 2,000 program storage addresses, Alpha or Numeric, color graphics screen. -- Sanding pressure PLC controlled. -- Thickness gauge 0 to 1.97". -- Fail-Safe emergency power unit for belt oscillation.
BUTFERING CLASSIC 2 KC/1100 Wide Belt Sander, (2) Heads; -- 43" Width capacity, Drum, Combination Head.Head Configuration:1st Head: -- Rubber covered Contact Roller 85 shore hardness 15 kW motor.2nd Head: -- Combination contact roller, 85 shore hardness, with sanding platen. 15 kW motor.Specifications: -- Abrasive belt size 1,120 mm x 1,900 mm. -- Contact rollers and sanding platen are all height adjustable. -- "Turret Stop" grit size compensation on contact rollers. -- Both main motors (15 kW) have automatic Star Delta starting. -- Safe, maintenance-free electrical main braking. -- Pneumatic tensioning of the abrasive belts. -- Electronic belt oscillation.Additional Features: -- Air loaded Floating Table for workpiece thickness compensation, includes pressure bars instead of pressure rollers. -- Motorized table height adjustment. -- LED Digital readout of the workpiece thickness.Feed System: -- Conveyor belt through-feed with automatic tracking. -- Driven by motor and worm gearbox to provide 2 selectable feed speeds of 4 and 8 m/min. -- Complete with pneumatic and inspection devices including mains air pressure regulator with filter. -- Rotating panel cleaning brush, with extra dust hood 140 mm diameter.Equipped with & features: -- Veneer sanding feature with workpiece controlled air cushion pad. -- Synchronized for both feed speeds and including extra sanding pad. -- Hand held workpiece thickness caliper 0-50 mm.
BUTFERING SKO 213RC2 Wide Belt Sander (2) Heads53" Width cap. Drum, Segmented PlatenHead Configuration1st. Head: 30 HP Drum with steel contact roll).2nd Head: Electronically controlled air segmented finishing platen, 25 HP motor. The contact roll height poistion with programable control. The platen consists of 35 mm segments designed to conform to panel size to minimize sand through. - Panel cleaning brush at the outfeed. Specifications: -- 54" x 75" Abrasive belts, electronic abrasive belt tracking. -- Both contact rolls with grit compensation. -- Variable conveyor belt feed, feed speed of 8 - 43 FPM, automatic conveyor belt tracking. -- 3 HP feed drive; infeed & outfeed spring loaded Rubberized holddown rolls. -- 1/8" - 5-1/2" Motorized thickness adjustment with LED readout. -- Automatic part thickness setup with indexing control.Equipped with & Features: -- Infeed panel "over-thickness" sensor. -- Electronic motor brakes on both sanding heads. -- Infeed & outfeed emergency stops, -- Safety interlocks on all doors. -- Roller infeed conveyor extension and motor load meters.
Call for Price
This machine has been removed from service. Everything is reported to be in good working condition. 53" Capacity 2-Heads: 1st - 30 HP Drum with steel contact roll, 2nd - 25 HP Electronically controlled air segments finishing platen 54" x 75" Abrasive belts Variable Feed Speed Automatic part thickness setup
C.R. Onsrud 241G18D Panel Pro CNC Router With ATC & Boring;5' x 20' Worktable, 11" Z-axis stroke; machined table with (3) multi-vacuum zones, moving gantry bridge and vertical supports. -- Equipped with:(1) 4-Pole 18 HP "HSK-63F" Electro Spindle, infinitely programmable spindle speeds up to 24,000 RPM, 12-position ride along ATC tool changer. (1) 9 spindle vertical drilling unit. -- Closed loop: Brushless AC Servo motors drive dual helical rack & pinion on the moving grantry & precision ball screws on the bridge & vertical axes; 2,000 IPM max. machining speed (straight or contour), 2,800 IPM max. traverse speed. -- All axes:ride on extra large precision contour linear guideways, axis travels provide full table coverage. -- Controller & Operator Interface:Industrial "OSIA" Machine Control System is compatible with virtually all CAD/CAM packages that generate standard M & G code. -- Featuring: Simultaneous 4-axis motion, 32-bit RISC processor; 4-port Ethernet connection, inch/metric operation and feed rate & spindle speed override. -- Complete with: (2) 10 HP DEKKER Vacuum Pump, assorted tool holders with collets, label printer, vacuum lift, manuals and documentation.Actual model "241G18D Panel Pro"
This is a CIII INDUSTRIES STAIN BOSS flow coater with a width capacity of 16 inches and thickness up to 8 inches. This machine looks rough but it has just recently been restored by the manufacturer and the invoice showing work done is attached in this listing. Here are some basic set up and operating steps: Adjust the lumber guides to 1/8” wider than the board to be run. Next adjust the pinch roll parallel with the face of the board. Then insert the board into the machine and adjust the pinch roll just tight enough for the drive roll to pull the board through the machine. Position the nozzles so the coating makes contact with the face and edges of the board. The bottom nozzles should be aimed toward the back of the board and the drive roll surfaceWith the board in the machine, adjust the first top brush to be parallel with face of the board. Then lower the brush until even contact is made with the board. Finally, lower the brush an additional three turns on each side.Next, set the second top brush in the same manner to the contact point. Lower this brush an additional one and one half turns on each side.Finally, adjust the side brushes into the board at a depth of 1/4 of an inch.Adjust the first brush set to a speed fast enough to push back a wave of coating. The second brush set should be adjusted to a slower speed - just fast enough to even out inconsistencies in the coating. The side brush speed should be set just fast enough to effectively brush the sides.Drive roll speed or line speed should be set as fast as the brush settings will allow - still maintaining consistent coating coverage.Set the air regulator to 60 psi. Once this is set you will not need to change it. Use the gate valve to adjust the air flow to the pump to control the coating volume.Do not run the pump with the ball valves closed! Doing so will create a tremendous back pressure in the coating system and when a valve is opened will cause a high pressure blast of coating to exit the nozzle. Always adjust the ball valves to a partially open position – never wide open. You will control the amount of coating to each nozzle by the position of the ball valves. The partially opened valves help reduce any pulsation caused by the strokes of the pump. The coating will flow more smoothly with some back pressure against the pump. Note: The top valve is closed since it is only used for the cleanup hose.
C.R. ONSRUD 122C12 Twin-Table CNC Router with ATCSpecifications: -- Twin 61" x 61" Moving tables can function independently for unload/load on one table while the other is in process or in tandem as a single 122" x 61" table. -- Each Table with:Universal type single-zone vacuum plenum for use with spoil board or pods and includes pop-up pins for panel registration . -- Equipped with:(1) COLOMBO 12 HP 4-Pole HSK spindle, variable speed to 24,000 RPM, and 12-position tool carousel. -- Closed Loop:"Brushless" AC Servo Drive System with precision ground ball screws, 3,400 IPM max. machining speed. All axes ride on extra large THK precision contour linear guideways; cast iron fixed gantry bridge and vertical supports. -- INDUSTRIAL:"AMC" Machine control system is compatible with virtually all CAD/CAM packages that generate standard M & G codes. -- Options Include:A New X-Axis ball screw;NOTE: This machine in EX-FACTORY'S Zeeland, MI facility - Cleaned, Checked and Certified by EXF's Senior Tech! ...the "Triple CCC" Seal!
C.R. ONSRUD - 144G10, ...CNC Router, 5' x 12' with ATC:Moving gantry CNC Router with a 144" x 60" worktable in a front-to-back configuration; machined Phenolic vacuum plenum with: (3) Zones; cast iron moving gantry bridge & vertical supports. -- Equipped with: (1) 10 HP "ISO-30" Type ATC Spindle with side mounted 8-position carousel and infinitely programmable spindle speeds from 0 - 18,000 RPM. -- Drive system:Closed loop brushless AC Servo motors drive rack & pinion on both sides of the gantry and precision ball screws on the bridge & Z-axis; all axes ride on extra large THK precision contour linear guideways. -- Axis travel:X-axis 61", Y-axis 145" with the Z-axis at 11". --Upgraded Control by Power Automation:Industrial "Power Automation" PC Front-End" Machine control system is compatible with virtually all CAD/CAM packages that generate standard M & G codes; built into "Roll Around" Pedestal console. -- Featuring:Simultaneous 3-axis motion, 32-bit RISC processor w/115,000 baud rate download capability; RS-232 port, inch/metric operation, and feed rate & spindle speed override. -- Complete with:25 HP QUINCY Vacuum System, assorted tool holders with collet & cover nut, and documentation.
C.R. ONSRUD 122C16C CNC Router with Twin Tables, ATC & C-Axis:Twin 60" x 60" Moving tables can function independently for unload/load on one table while the other is in process, or in tandem as a single 120" x 60" table, each table has a universal type single zone vacuum plenum for use with spoil board or pods. -- Equipped with:(1) 16 HP HSK-63F type ATC spindle with C-Axis 360° rotation, variable speed from 6,000 to 18,000 RPM, ceramic bearings, and 12-position tool carousel. -- Closed loop "brushless" AC Servo drive system with precision ground ball screws, 1,500 IPM max. machining speed, all axes ride on extra large THK precision contour linear guideways; cast iron fixed gantry bridge and vertical supports. -- INDUSTRIAL"AMC 4" Machine control system is compatible with virtually all CAD/CAM packages that generate standard M & G codes; built into "swivel arm" mounted console. -- Featuring: Simultaneous 3-axis motion for "full 3D" capability, 32-bit "RISC" processor w/115,000 baud download capability; RS-232 port, hand held controller, inch/metric operation, and feed rate & spindle speed override while cutting. -- Includes:Assorted tool holder, manuals and documentation. approximate footprint 199”L x 138”W x 96" HNOTE: There is no vacuum pump included.
C.R. ONSRUD "MATE" 97M12 Series Moving Gantry 4 X 8 CNC Router with ATC:97" x 49" Axes travel in a front-to-back configuration; Phenolic surface, machined universal grid vacuum table (1) vacuum zone with (3) pop-up positioning pins. -- Thermal heat treated:Stress relieved & normalized steel frame base & moving gantry bridge, vertical supports & Dual Drive. Full 3-D capability, 1,400 IPM machining speed, 10" under bridge clearance and 9" Z-stroke. -- Equipped with:(1) 12 HP "HSK-63" spindle taper ATC quick change spindle with rear mounted 10-position wine rack type tool-changer; spindle speed fully programmable & reversible, infinitely variable speed from 1,000 - 24,000 RPM. -- Drives:High Accuracy Digital Brushless closed loop AC Servo motors drive rack-n-pinion on both sides of the gantry and precision ball-screws on the bridge and Z-axis; all axes ride on extra large THK precision contour linear guide-ways. -- Control:Onsrud B&R handheld with VNC PC front link. Automatic handheld machine control system (4) USB and serial connectivity; integrated VNC-PC front software & interface board are included to allow a user provided PC to be easily connected with reliability, functionality, and safety; -- Featuring:Simultaneous 3-axis motion, 32-bit RISC processor w/115,000 baud rate download capability; hand held controller, inch/metric operation, and feed rate & spindle speed override. -- Includes:Assorted tool-holders, manuals, and 18 HP BECKER vacuum pump.
CADORET Manual Finger Joint System: Shaper Section includes right and left hand Shaper Units, each with AC variable speed drives from 30 to 60 FPM.Features: Shapers with hand-wheels and digital readout scales; on on the horizontal saw adjustment and one each on vertical and horizontal spindle adjustments, -- Retractable guide knives for running flooring; quick change chain lug back up blocks for end matching. -- Extended arm for running up to 16' long material; roller track for material longer than 48". -- APQUIP Glue Applicator on second Shaper. -- 20' Manual Press Section with 5/8" to 3" thickness cap; 3/4" to 8" width cap.; 36" to 240" assembled length capacity. Hydraulically driven rubber rolls and adjustable length stops. -- High efficiency motors used throughout.
Call for Price
CALPE L6-1600 Spindle Sander with Hopper Feed. -- (6) Spindles, semi-automatic sanding machine; distance between centers 63", 6-3/16" max sanding diameter, capable of sanding 1800 spindles per hour. -- 4 HP - 1,800 RPM head motor, (5) sandpaper holders, each for different grits, 4000-3200-2200-850 RPM head spindle speeds. Copier unit that follows all contours. -- Oscillating sanding units & stationary pick up of part. -- NOTE: This sander was running with lathe on our record number LC-01811 and owner prefers to sell at the same time.
CALPE TH5-1600 Heavy-Duty High-Production, Fully Automatic CNC Lathe: General Description: -- Multi-Spindle cutting simultaneously, (5) spindles using V-type gouge knives. -- 63" (1,600 mm) Max. distance between centers; 5-1/2" (140 mm) max. swing diameter between spindles. -- CNC Controlled with 3.35" (85 mm) travel for depth of cut. Motors/Speeds: -- (2) Head stock motors, each 12.5 HP - 1,750 RPM; -- CNC controlled electronic variable speed of main head from 100 - 6,000 RPM. 2 HP approx hydraulic drive. -- Fast return travel of up to 590 IPM (15,000 mm/Min). -- CNC controlled feed speed carriage, variable up to 50 FPM (15 MPM). -- Loading device & tail stock powered by hydraulic pump with 2 HP - 1,750 RPM motor; No. 5 Morse taper on main spindle shaft. Features: -- Automatic loading & unloading device; carriage mounted with linear guides providing high precision movement. -- Full CNC controller with on-screen CAD programming for all products.Matching CALPE L6-1600, record number LC-010996 spindle sander is available at additional cost at same facility.
CAM-WOOD - KT2, ...Edgebander. Compact - Single Sided (mfg. in Italy);0.4 mm - 2 mm Max. edge thickness cap., 10 mm - 45 mm (1-3/4") panel thickness cap. (when edgebanding 2 mm PVC, max thickness is 22 mm or (3/4"). -- Equippped with: Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 2 mm max.) with 2 mm PVC cap. guillotine. -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time. -- Guillotine unit to cut edgebanding in coils up to 2 mm thick. -- Workstations: Single end trimming unit with pneumatic power knife to cut at 90° flush to the leading & trailing edges of the panel. -- Top & bottom High Frequency flush trims (0.46 HP - 12,000 RPM HF motors). -- Includes (2) 2 mm radius cutters. -- Feed Track & Speed: 0.35 HP Feed drive for a feed rate of 15 FPM; feed chain with rubberized surface of pads. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Sound enclosure protects the operator from noise and debris.Engineered & Manufactured by TECNOMA S.r.l., Italy.
126" (3,200 mm) Cutting length, 3.94" (100 mm) cutting height, motorized back fence from 1" - 31-1/2" cap. fence travels on hardened ways, 0.5 HP motor, LED readout for fence positioning & fine adjustment by front mounted hand wheel. -- Equipped with: Hydraulic pressure beam-and-knife powered by 10 HP hydraulic pump motor, 6" wide pressure beam with cutting force adjustment for beam-and-knife, beam assembly with self-lubricated slide ways. -- Complete with: Cutting line with 4-side plastic cutter counter gib, cutting edge light for material positioning, 2-hand push button operation for safety; features operation selection for manual & automatic working cycles.