• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
2 Results Found for End Matcher Viewing 1 - 2 of 2 results
STANDARD LISTINGS
CANTEK CFS-100/EM-12 Defector and EM-12 Endmatcher DEFECT AND END-MATCHING SYSTEM consisting of a Cantek model "CFS-100" Optimizing Cut-Off Saw followed by a Cantek "EM 12" Through-Feed End Matcher and with the following specifications and features:Specifications: -- Working dimensions: 4" x 11" or 3.2" x 12" cutting capacity with 18" x 30 mm bore sawblade driven by a 10 HP motor, 3,200 RPM arbor speed; 2.7 HP servo drive feed system drives the stock up to 260 FPM; -- 0.787" Min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. -- Machine is ideal for defect cutting finger joint blocks or cutting fixed lengths from a predetermined cutting list; -- Cuts fixed lengths, random blocks and optimization; provides 3 to 5 times higher production than manual cut-off saws, plus 5% + material recovery and 5% yield increase compared to manual cutting.Features: -- Compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls. It can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm /0.40"; control employs a touch screen for easy learning and operation. 48" Long infeed table standard - longer available option; 18" carbide blade included. (5) Cutting modes: -- Adjustable end cuts to a max. of 10 mm (0.4") -- Fixed length of cutting mode -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only) -- Cutting on fluorescent marks with double end trimming -- Reading fluorescent marks with double end trim, fixed length, finger joint block cutting. CANTEK model "EM-12" END MATCHER & FINGER JOINT SHAPER with continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity.Specifications: -- 295 FPM max. feed speed; 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor and 1/2 HP cutter stroke motor. -- Clamping from top and outside side; 40 mm spindle dia.; 6" dia. dust outlets; requires 85 PSI @ 12 CFM and a 12.5 total connected load. Standard features include: Heavy duty self supporting main frame; compact design
Equipment Location:NORTHEAST
Jeff Terrill
800-374-5009 ext:349
COMPUTERIZED DEFECT AND END-MATCHING SYSTEM consisting of a Cantek model CFS-100 Optimizing Cut-Off Saw followed by a Cantek Model EM-10 or EM 12 Through-Feed End Matcher and with the following specifications and features: -- 4" x 11" or 3.2" x 12" cutting capacity with 18" x 30mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP serve drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for defect cutting finger joint blocks or cutting fixed lengths against a predetermined cutting list; cuts fixed lengths, random blocks and optimization; provides 3 to 5 times greater production than manual cut-off saws.; 5% + material recovery )5% yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm /0.40"; control employs a touch screen for easy learning and operation; new machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included. -- (5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm(.4") -- Fixed length of cutting mode -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only) -- Cutting on fluorescent marks with double end trimming -- Reading fluorescent marks with double end trim, fixed length, finger joint block cutting. -- CANTEK model EM-10 / EM-12 END MATCHER & FINGER JOINT SHAPER with continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 10" or 12" width capacity; 295 FPM max. feed speed; 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; 5.5 HP shaper motors, 1 HP feed motor and 1/2 HP cutter stroke motor and 24-volt control system; clamping from top and outside side; 40mm spindle
Equipment Location:PACIFIC NORTHWEST
Jeff Terrill
800-374-5009 ext:349