• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
3 Results Found for Jointer and Finger Jointer Viewing 1 - 3 of 3 results
STANDARD LISTINGS
CAM-WOOD SFJ-530 Finger Joint ShaperSingle Fingerjoint Shaper with 8" min. and unlimited max. block length; 6" max. block thickness; 12" max. block width (horizontal joint only); 16" table working width.Equipped with: -- Shaper spindle powered by 15 HP belt drive motor with 50 mm dia. spindle turning at 9,000 RPM; swings 6" max. dia. cutter. -- Trimsaw powered by 3 HP direct drive motor at 3,500 RPM and a 1" dia. saw spindle; swings 10" max. blade dia. -- Table cycles 2-1/2 times per min. via hydraulic system with 2 HP hydraulic power unit. Includes 5" dia. dust outlet.Features: -- Manual Fingerjointer performs end trimming and shaping functions on right and left end of blocks. Air-operated clamp holding blocks firmly in place. After work piece is clamped, table feeds past the saw and shaper spindles to perform trimming and fingerjoint operations; trim saw cuts blocks exact 90 degree ends. -- Shaper spindle is precision-constructed for cutting fingers accurately; swings up to 6" dia. tooling. -- Spindle height adjustment displayed on dial readout for easy adjustment. -- Table travels on a precision linear guide for stability; table traverse driven by hydraulic power system smooth and accurate block feeding. -- Variable feed speed permits proper feed for hard or soft wood. -- Cast iron frame and table for durability.Also available at extra cost: -- Fingerjoint glue applicator, add $2,590 -- Fingerjoint assembly press, add $26,990
Equipment Location:WEST COAST, AL
EX-FACTORY INC.
704-841-2001
CAM-WOOD SFJ-AUTOSET Automatic Finger Joint MachineCOMPLETE WITH RIGHT & LEFT SHAPERS, GLUE APPLICATOR, CUTOFF SAW, AND ASSEMBLY PRESS. Cuts vertical and horizontal joints dependent on how blocks are loaded. -- Fully automatic finger joint production line to produce finger jointed boards from short blocks.Shaper Features: -- Right Hand Shaper end trims incoming blocks and shapes fingers on the right end of blocks. -- Left Hand Shaper end trims and machines opposite fingers. -- Shapers are equipped with (2) trim saws; (1) saw blade for cutting even end of blocks and (1) blade for scoring to ensure a clean joint. -- Air-operated holddown clamp holds blocks firmly in place. After blocks are clamped, table feeds past the trimming and shaping operations. -- Shaper spindles are precision constructed to cut accurate finger profiles; spindles accommodate up to 6” dia. cutter heads. -- Spindle height adjustment is displayed on a digital readout for easy adjustment. -- Table travels on precision linear guides. -- Table traverse is powered by a hydraulic feed system which ensures a constant and smooth feed of the blocks and results in an accurate and precise cut. -- When the Right Hand Shaper completes its cutting process, the conveyor table automatically transfers blocks to Left Hand Shaper and returns to the starting position to accept new blocks. -- When the Left Hand Shaper is finished, blocks with adhesive on one end are automatically transferred to an inspection station and sent to the Assembly Press.Press Features: -- The Press is automatic and performs (3) functions: preliminary assembly of finger jointed blocks, cutting the pre-assembled blocks to predetermined length, and final assembly or “squeeze”, powered by a heavy duty hydraulic system. When pressing is complete, assembled boards are feed out of the Press. -- Includes a power feed for fast feeding of blocks and auto stops which are set according to the finished board length. The saw cuts as the stop is contacted. -- Furnished with cut off saws as standard equipment for cutting workpieces to the length desired. -- The maximum length of assembled boards is 16'. Longer Presses are available. -- System employs an advanced programmable logic controller for ease of operation and maintenance. -- The machine's motion sequences are displayed by the signal lamps for easy checking in the event of a malfunction.Shaper Specifications: -- Thickness capacity: 3/4” - 6”; Incoming block length: 8” - 31”; Assembly Press width capacity: 3/4” - 6”; Assembly Press thickness capacity: 3/4” - 3”. Maximum finish press length: 181” (longer available) -- Block Transfer Conveyor Unit: Conveyor receives and transfers blocks to the Right Hand Shaper. Table Width: 24”; Table Depth: 30”; powered by a 1/2 HP Motor. -- Right Hand Shaper scores, trims and shapes the finger at right end of material. Table width: 24&rdq
Equipment Location:WEST COAST, AL
EX-FACTORY INC.
704-841-2001
CAM-WOOD MODEL SFJ-6-195-AUTO 6” X 195” Automatic Finger Joint Line: -- Features: -- Automatic finger joint production line complete with Right Hand Shaper, Left Hand Shaper with Glue Applicator, and Assembly Press and Cutoff Saw to produce finger joint boards up to 16’ long. -- Left Hand Shaper Section performs scoring, end trimming, shaping & gluing functions on left end of blocks. -- Motors are fitted to the Shaper Sections where saw blades are mounted to for score to ensure clean joints as well as truing the ends of blocks. -- Blocks are clamped to Shaper tables from the side and top; tables feed blocks thru the Shaper Sections while performing scoring, trimming, and shaping operations. Glue is applied at the second Shaper Section. -- Shaper spindles are precision constructed for cutting finger profiles accurately; accommodates 6” maximum cutter diameter. -- Spindle adjustments are displayed on a dial readout for quick, easy, and accurate adjustments. -- Shaper tables travel on a precision linear guides. -- Table stroke is driven by a hydraulic power system to ensure stable, smooth feeding. Accurate cuts are guaranteed -- At the end of the first Shaper’s table travel, a conveyor table automatically transfers blocks to second Shaper while the first Shaper table returns to its starting position and immediately accepts blocks for succeeding work. -- When the second Shaper has completed its cycle, including glue application, blocks are transferred for inspection and sent to the Press Section for assembly -- The Assembly and Press Section performs three functions; preliminary assembly of blocks, cut assembled blocks to length, and final pressing with a heavy duty hydraulic system. After final pressing, boards are automatically fed out of the Assembly Section for stacking. -- Press Section includes a feed system for fast feeding and alignment of blocks. Includes an adjustable length stops that triggers the automatic cut-to-length saw. -- Press Section accommodates up to 16’ maximum length. Other lengths available. -- System employs advanced programmable logic controller for easy operation and maintenance. -- The machine's motion sequences are displayed by signal lamps for easy troubleshooting. -- INCLUDED EQUIPMENT: -- Machine configured for scoring and precision end trimming of blocks, machining fingers, applying adhesive, preliminary assembly, cut-to-length, and final pressing of joints for manufacturing boards up to 16’ long from short blocks. Following are specifications for a feed through machine that includes a right side Shaper, left side Shaper & Glue Applicator, Assembler & Cut-To-Length Saw and Press sections. -- SYSTEM CAPACITY: -- Incoming blocks: Up to 6” wide x 3/4” to 6” thick x 6” to 31” long -- Press: 3/4” to 6” width x 3/4” to 3” thick x up to 16’ long (up to 20’ optional) -- MACHINE SPECIFICATIONS: -- Block Infeed Transf
Equipment Location:WEST COAST
Jeff Terrill
800-374-5009 ext:349