800-459-2148
713-729-6455
Sawmill Exchange specializes in brokerage of small mills. Thin kerf, circle, scragg and more - when you need a small mill call Sawmill Exchange FIRST!
306 Results Found
800-459-2148
713-729-6455
JACKSON LUMBER HARVESTER - Refurbished Jackson Lumber Harvester - Cab with hand and foot controls - Hooked up to a PTO to run blade - All hydraulics and electrics redone - Currently being wrapped up and tested - All motors included, hydraulic tank w/ pump - Attractive Financing available with 50% down
$5,500
Keener Built Hydraulic Band Sawmill. COMPLETELY REBUILT and engineered with new gas powered deck. 25 HP Kohler gas engine. Cap 28" throat, 36" x 16'. Mill is operational and can be demonstrated. Original mill built between 1997 and 2003.
$150,000
$2,500
2 Auger Converyors. Conveyor 1: Photos: P1080771 ""772 ""793 ""790 ""794 24' length 16" wide trough Heavy Duty Auger: 1/4" thick x 14" diameter Gear reduction : 20/1 $2500 Conveyor 2: Photos: P1080773 "774 20' length 16" wide trough Heavy Duty Auger: 1/4" thick x 14" diameter $2000 Both conveyors need new electric motors Both conveyors are heavy duty and used in bark and sod. Can also be used for top soil. Electric motors with gear drive 20/1 gear ratio but motors were burned in fire. Ability to load- available.
$2,000
Lenox Friction Bandsaw Blades: Pallet dismantling blades. 47 per pallet. 2 pallets available. 21'-6" Bimetal 1". .035 10 TPI. $2250.00 per pallet. Shipping weight 175# per pallet. Buyer responsible for cost of shipping. No rust, clean, new, in boxes. Dock side pick up. Asking Price: 2250.00
$3,000
REDUCED TO SELL! $8000. Little Chipper 27-5. 7" wide x 2 1/2" H in feed opening. 10' in feed conveyor belt. Designed to chip scraps from table or rip saws into sawdust. Has hydraulic motor. Like new condition.
2008 Logmaster LM2 - Custom Built with one owner - 30 HP Kohler Gasoline Engine - Fully Hydraulic - Cap 12' x 28" - 19’1” (229-inch) Band saw Blade –One inch width - Ten gallon fuel tank - Always received regular maintenance
$16,000
Lucas 6-18 Sawmill - Just like new with only about 2 hours - 18 HP Vanguard V-twin engine, with electric & manual start - Cap 20' x 6" on a single cut and 12” on a second cut. - Easy to assemble and transport. - Cuts true and fast - Comes three extra blades, tool kit, and all documentation and introduction DVD
2017 Lucas 8-30 - Kohler 30 HP gas engine with 60 hours - Slabbing attachment - Planing attachment
$3,250
Location: Wisconsin Marathon Electric Frame 44ST Electric Motor. 100 HP, 890 RPM, 460 volt AC, high efficiency, new surplus motor. Call 800-459-2148 for more info
$6,500
2 Mattison Lathes and Tooling Mattison 55F Manual - 15HP, 220/440v Mattison 69-42” Hopper Auto Lathe - 15HP, 220/440v Includes: 21 boxes of T-slot cutter heads with blades mounted and Tall End sander.
1983 Mattison Straight Line Rip Saw - single blade, model 404. 3 ph electric with 15 HP motor. 2 HP feed motor with 2 feed speeds of 50 and 100 FPM. Cap 4" thickness.
$3,800
1949 McDonough Manufacturing McDonough 54" Vertical Bandsaw. Model McDonough 54" Vertical Bandsaw.