NELSON HARDWOOD LUMBER CO.
NELSON HARDWOOD LUMBER CO.
Wausau Sales Corp.
PRAIRIE du CHIEN, WI
REAL ESTATE TO BE OFFERED AT 9:00 AM
Parcel #1
Approx. 12+ acres w/ large log storage yard and good, graveled, truck, trailer, loading and driveway areas.
Mill Building
Approx. 21,500+ Sq Ft Steel-clad pole building with fire suppression sprinkler system throughout. This houses sawmill, debarking, chipping, and grading areas.
File Room/Shop
Approx. 5600 +/- Sq Ft, 2 story insulated building. File room on top floor w/ shop & breakroom area on main floor.
Office
Approx. 1200 +/- Sq Ft wood construction office building.
Parcel #2
Approx. 7350 +/- Sq Ft Steel Insulated Building w/ 18 +/- side walls, in floor heat, N.G. Boiler & Taylor Wood-fired boiler, overhead insulated doors, currently used as truck repair shop, situated on approx. 3 ½ acres.
Closing on parcels #1 and #2 to be on or before July 15, 2022.
Parcel #3
Complete Dry Kiln Operation; Located at 27133 Sawmill Rd. Richland Center WI, From Richland Center, take US Hwy 14 east 2 miles to Sawmill Rd then right ¼ mile.
5 – Irvington Moore USNR 50,000 BF Each Dry Kilns. Repaneled & Repaired in 2015 w/ 2006 USNR VFD Controls (In Very Good Condition)
2006 Hurst 300 HP waste wood boiler w/ water conditioner reclaim tank & controls. Feeder system consists of walking floor storage, vibratory conveyor & stoker – housed in 40” x 80” steel/concrete building.
Kewanee 200 HP natural gas back up boiler w/water conditioner & reclaimer.
3 – Steel Air Drying Buildings; 2 – 36' x 115’; 1 – 36' x 96’ w/ concrete floors & enclosed ends.
2 – Lumber Storage Buildings: Steel Clad, wood frame w/ roll-up doors: 1 – 60' x 290’ & 1 – 60' x 100’.
60’ x 40’ Drying Stick stacking shed
Planer & Stacking Building
100’ x 120’ Steel Frame Insulated Building w/ concrete floor, fully insulated.
Situated on 30.47 +/- Acres w/ very nice graveled & fenced yard. There is plenty of room for expansion of buildings.
14 Unit Sawdust/Chip Bin.
EQUIPMENT TO BE OFFERED WITH DRY KILN OPERATION
Newman EPR – 24 Quiet Cut Helical head double sided roughing planer; 6” x 24” capacity, 60hp on top head; 50 hp on bottom head w/ Pinch Roll; s/n 15279.
2’ x 38’ rubber belt infeed conveyor w/ electric drive (Into Newman).
106” x 42’ 4 strand transfer deck w/ C 55B chain, electric drive w/ wood decking.
Mattison 202 straight-line rip saw, Nice; s/n 2367207004.
40” x 10’ outfeed roll table.
Froedge Breakdown & Lumber Stacker
4 strand infeed deck into 3 arm tilt hoist to 5 strand transfer deck into 5 strand unscrambler, into 5 strand H78B rooftop chain deck, into lumber stacker w/ hydraulic package deck w/ power off-feed rolls w/ stick-removing conveyor.
Closing on parcel #3 will not be before October 1, 2022.
REAL ESTATE TERMS: 10% Buyers Premium. 10% down day of auction in the form of Cash, Cashier’s Check or Certified Funds, Personal & Company Checks must have current bank letter of guarantee. Balance is due at closing. Buyer will be provided a Warranty Deed free and clear of all encumbrances and liens subject to all restrictions & reservations of record or by use. Property is being offered subject to Owner’s confirmation.
Chad Glaze – Broker – 715-340-6162.
2 – McDonough 6’ Band Mills w/2 Cleereman LP Carriages & Scanners
LEFT HAND MILL
1995 Cleereman LP 42 linear position 16’ carriage, 14” wheels; 6'3" & 4’4” block spacings, 50’ of 60# rail, s/n LP42-533.
Cleereman 30 hp electric/hydraulic power unit w/oil cooler & oil reservoir tank.
2019 Cleereman Linear Carriage controls w/3D 8 head scanning optimizer w/ cameras.
Mc Donough Mod 6-7A. LH band mill; air strain w/slat bed off bearer; s/n 72MA-438.
Approx. 14 New & Used 6’ LH saw blades.
WEG 200 hp electric motor.
Toshiba Mod TE-361 BP 200 hp starter.
Tyrone Berry Mod SMA 250 C-40' shot gun feed works w/100hp electric/hydraulic power unit & oil reservoir.
50 hp electric/hydraulic power unit w/oil reservoir (under cab).
2019 Cleereman 5’ x 8’ cornerless insulated control booth w/ heat & A.C.
Custom Built heavy duty bar type log turner.
10 hp electric/hydraulic power unit w/oil reservoir tank (under steps).
Mellott 24” x 15’ pneumatic slab drop belt w/electric drive.
Mellott 10” x 20’ 3 strand log infeed deck w/ Tulsa Winch; electric drive; hydraulic stop & load (into mill).
Mellot 30”x 45’ x8” power roll case w/ electric drive & 6 arm pneumatic kicker.
Mellott 117” x 27’ 4-strand transfer deck, C118 chain; stops w/ Tulsa Winch, electric drive.
Mellott 80” x 8” 3 strand transfer deck w/ H78B chain w/ Tulsa Winch, electric drive.
RIGHT HAND MILL
1995 Cleereman LP42 linear position 16’ carriage; 14” wheels 6’3” & 4’4” block spacings, 50’ of 60# rail, s/n 42-507.
Cleereman 30 hp electric/hydraulic power unit w/oil reservoir & oil cooler.
2018 Paw-Taw John All Knee Linear Scan Carriage set works w/scanner.
Mc Donough 6-7A R.H. band mill; air strain w/slat bed off bearer; s/n 72MA-275.
Approx. 14 New & Used 6’ bandsaw blades.
WEG 200 hp electric motor.
Toshiba Mod TE – 361 BP 200 hp Starter.
Tyrone Berry Mod SMA 250C – 40’ shot gun feed works w/ 100 HP electric/hydraulic power unit w/ oil reservoir.
40 hp electric/hydraulic power unit w/ oil reservoir (under cab) (Band Mill).
Cleereman 5’ x 8’ cornerless insulated control booth w/ heat & A.C.
Custom Built heavy duty bar type log turner.
10 HP electric/hydraulic power unit w/ oil reservoir (under steps) Runs log turner.
Mellott 24” x 12’ pneumatic slab drop belt w/ electric drive.
Mellott 10’ x 20’ 3 strand log infeed deck w/ Tulsa Winch; electric drive & hydraulic stop & load (into mill).
Mellott 117” x 13’ 4 strand transfer deck, C118 chain; stops; Tulsa Winch; electric drive.
Mellott 30” x 48’ x 8” power roll case w/ electric drive & 5 arm pneumatic kicker.
PRECISION DEBARKER
Precision P636 slant track Rosserhead debarker, 16” capacity; 50hp on head; s/n D 232.
11’ x 48’ 3 strand log infeed deck w/ 4 arm hydraulic stop & load; electric drive.
Patz 17” x 128’ barn sweep bark conveyor w/ 32’ steel chute & electric drive (Clockwise).
55’ WD110 chain log trough outfeed conveyer w/ 2 way 4 arm pneumatic log kickers & 1 way 3 arm pneumatic log kicker w/ Tulsa Winch; hydraulic drive.
15 HP & 10 hp electric/hydraulic power unit w/ oil reservoir & oil cooler.
CROSBY EDGERS & REMAN EQUIPMENT
Crosby 36” board edger w/ 40 hp electric motor; s/n 05307T
Crosby 20’ tailing belt.
Lazer Light & Assembly.
Crosby Size 32 Reman edger w/ 30 hp motor; s/n 12312U.
Baker A single head horizontal band resaw w/ 32’ feed thru belt conveyor.
Alden Multi Rip Saw w/ 60 hp motor & blower.
2 Arm Breakdown hoist (Not Installed).
SAW TRIMMER; GRADING DECK; GREEN CHAIN; TRANSFER DECK; TIE SORTER
Newman Whitney KNO-24 Automatic Selection Overhead Trimmer; 4’ - 16’; 8 saw; s/n 24-040898.
Mellott 117” x 87’ 3 strand green chain w/ Tulsa Winch; electric drive.
Mellott 10’ x 32’ 4 strand grading deck w/ 30” pop up roller (to feed tie sorter) w/ Tulsa Winch; electric drive.
Mellott 24” x 52’ 2 sort tie sorter w/ electric drive.
Mellott 10’ x 21’ 4 strand transfer deck w/ electric drive.
Mellott 10’ x 60’ 4 strand transfer deck; H78A rooftop chain w/ 11’ 4 strand drop transfer deck; electric drive.
36 – steel lumber stacking carts.
CHIPPER & WASTE WOOD HANDLING
Precision 66” chipper; s/n 3010.
250 hp electric motor.
Toshiba TE2 series solid state 250 hp, 450 amp starter.
Precision PCS-77 7’ x7’ chip screen; s/n 2168.
Precision cyclone.
Phelps 48” van loading blower w/ 25 hp motor; 2 Y pipes & diverters; many feet of new pipe.
Approx. 24” x 100’ elevated belt conveyer w/ hopper (for van loading).
Precision 22” x 26’ vibratory conveyor (into chipper).
MDI CR 85 metal detector w/ 4’ fiberglass vibratory section; s/n M4-0416.
Mellott 20” x 65’ belt conveyor w/ electric drive.
2 – Mellott 20” x 45’ belt conveyors w/ electric drive.
Mellott 20” x 42’ belt conveyor w/ electric drive.
Mellott 20” x 29’ belt conveyor w/ electric drive
Mellott 18” x 40’ belt conveyor w/ electric drive.
Patz 16” barn sweep conveyor w/ approx. 360’ of chain; 40' steel chute; electric drive; (counter clockwise).
AIR COMPRESSORS
2015 Gardner Denver Mod EBE 99006F Electra Saver II 30 hp rotary screw air compressor w/ air reservoir tank; 6,276 hours; s/n S467231.
Gardner Denver Mod EBERGH Electra Screw 30hp rotary screw air compressor w/ air reservoir tank, 81,157 hours; s/n U69458.
Gardner Denver Mod EBE99K22 Electra Screw rotary screw air compressor w/ air reservoir tank; 63,100 hours; s/n S054218.
Pneumatech Mod EH-250 regenerative air dryer; s/n 0310-S139606-041892.
ELECTRICAL
Westinghouse Motor Control Center w/ 34 buckets.
Westinghouse 1000 amp 480 volt Switchboard w/ 3 - 250 amp, 1 - 150 am; 1 – 125 amp; 2 – 70 amp; 1 – 60 amp breakers.
Square D 600 VAC 400 amp. 350 hp disconnect.
Plus large amount of assorted disconnects, starters, wire & conduit.
FILE ROOM & SHOP EQUIPMENT
Armstrong automatic electronic leveler; s/n 20755.
Armstrong #4 LH band saw sharpener w/ stands & clamp; s/n 14895.
Armstrong #4 RH band saw sharpener w/ stands & clamp; s/n 14999.
Armstrong #5 stretcher roll; s/n 14938
Armstrong #12 welding clamp.
Armstrong bench w/ anvil.
Hanchett Size 136 circle saw grinder; s/n 815.
Michigan 48 chipper knife grinder; s/n 1078.
Precision 6K 40 tub knife grinder; s/n PAG675.
Miller Synchrowave 180 SD CC/AC/DC Square wave power source TIG welder; s/n LE219695
Miller CP 302 CV/DC welding power source; s/n KH480491 w/ Miller 60 24V constant speed wire feeder.
Mill Rite Mod MVN vertical milling machine; s/n 68539.
Walker Turner radial arm drill; s/n 7-642.
Jet Dia. M 150 horizontal bandsaw.
Clemco Classic 150 PSI sand blaster.
DCE Unimaster dust collector.
Assorted Shop &Mechanic Tools.
BOILER & WALNUT STEAMER
1999 Hurst “Cyclone” 40 hp vertical Natural Gas boiler; Approx. 10K was spent on the boiler in 2021; s/n V150-15-2.
2- kiln doors w/ truck; rack & frame.
Heat Exchangers.
PARTS AND ACCESSORIES
Sawmill; Debarker; Chipper; Loader; Truck & Trailer Parts.
Electrical; Hydraulics & Pneumatic Parts
Hardware: Nuts, Bolts, Fasteners.
Large Selection of Steel Cat Walk & Stairs.
WHEEL LOADERS, SKID LOADER, FORKLIFTS
2018 John Deere 624 K-II wheel loader; cab w/ A.C.; JRB Style Q.C.; 20.5R-25 tires; 6450 hours; s/n IDW624KTCJ686934.
2006 John Deere 544 J wheel loader; Cab w/ A.C.; JRB Style Q.C.; 20.5R-25 tires; 15,673 hours; s/n DW544JZ608552.
John Deere 3yd, 104” wide JRB style QC bucket; s/n 180197.
2018 B&D Mod BD600 Silage 6 yd. JRB Style Q.C. bucket; s/n B98196.
Fleco JRB Style Q.C 54” loader forks.
B&D JRB Style Q.C. forks w/ log clamp.
GEM JRB Style Q.C. 4’ forks; s/n 0613-6115-1-1.
Set of 18,000 lb. JRB Style Q.C. forks.
2-11' Hydra Turn Snowplows w/ JRB Style Q.C.
1984 Caterpillar 930 wheel loader; cab w/ heat; 17.5 x 25 tires; pin on bucket & forks; s/n 41K12584
1994 Volvo L70B wheel loader; cab w/ A.C.; 17.5R 25 tires; Q.C.; 23,608 hours; s/n XL70B10444X.
Q.C. 3 yd. Bucket (for Volvo).
Q.C. Log forks w/ clamp; 5’forks (For Volvo).
Mustang 940 E skid loader w/ forks & bucket; 2982 hours, s/n 5478163.
Taylor TYB-180M “Big Red” forklift, cab; 14.00 x 24 front tires, 8' forks; side shift, 6448 hours showing; s/n S-P5-14458.
LOG SKIDDERS
2000 John Deere 540 G III cable skidder; cab; 23.1 x 26 tires, 10,050 hours showing; s/n DW540GX577684.
1991 John Deere 540E cable skidder; cab; 23.1 x 26 tires, 11,725 hours showing; s/n DW540EC534530.
2 - 1978 & 1979 Caterpillar 518 cable skidders; Gearmatic Winches; 23.1 x 26 tires; 141 & 2935 hours showing; s/n 50S2471 & 50S2674.
Caterpillar 508 cable skidder; 23.1 x 26 tires; 1031 hours showing; s/n 9NC003422.
Several Pair of 23.1 x 26 skidder chains.
DOZER
1997 Caterpillar D5M XL crawler dozer; Cab; Allied Winch; approx. 7500 hours; s/n D5BXLFTC6GN00393.
LOG LOADER TRUCKS & PUP TRAILERS
2 – 2017 Mack GU 813 tandem axle log trucks; Mack MP8 445 C 12.8 litre engines; Maxi Torque ES 10 speed transmissions; 425/65R 22.5 front float tires; 11R 22.5 drive tires; aluminum wheels; 20,000 front axle; 66,000 rears; air ride cabs; spring suspensions; 2016 Roto Bec Elite 910 knuckle boom loaders w/ sure grip grapples; s/n 050588300-5-1 & s/n 05058300-4-1; 22’ steel log racks w/ aluminum headache racks & aluminum stakes; 164 K & 235 Miles; s/n IM2AX16C0HM038254 & IM2AX16C2HM038255.
2002 Mack CL 713 Maxi Cruise tandem axle log truck; Mack E7 427HP engine; Eaton Fuller 8 LL transmission, 425165R 22.5 front float tires; 11R 22.5 drive tires; aluminum wheels, air ride cab; spring suspension; Roto Bec Elite MT 26 knuckle boom loader w/ Sure Grip grapple; s/n 124334-2-1; 22’ steel log rack w/ aluminum headache rack & aluminum stakes; 123 K miles; s/n IM2AD09C92M012077.
1997 IHC PayStar 5000 SFA 6x6 Pre Hauler truck; Cummins M-11 Plus engine; Eaton Fuller 10 speed transmission; 550/60 - 22.5 rear float tires; Roto Bec Elite Charge Use knuckle boom loader w/ Sure Grip Grapple; s/n 10800520 RO – 6416; 21’ steel log rack; approx. 200K miles; s/n 24TTWAHT9VC017799
2015 Shop Built 2 axle 18’ log pup trailer; 11R 22.5 tires; aluminum wheels, air ride; steel stakes; s/n 100000000013542 WI.
1999 Rosa 2 axle 18’ log pup trailer; 11R 22.5 tires, aluminum wheels, air ride; aluminum stakes; s/n 100237.
1981 Cedar 2 axle 16’ log pup trailer; 11R 22.5 tires, spring ride; steel stakes; s/n 810901.
TRUCK TRACTORS
2004 Mack CX 613 Vision tandem axle sleeper cab truck tractor, 65” sleeper, Mack 427 engine; Eaton Fuller 10 sp trans; 285/75R 24.5 front tires; 285/75R 24.5 drive tires; aluminum wheels; air ride; 489K miles; s/n IMIAE06YX4N020185.
2003 IHC 9100 tandem axle day cab truck tractor; Cat C-12 425 hp engine; Eaton Fuller 10 sp trans; 11R 22.5 front & drive tires; aluminum wheels; air ride; 12,000 front axles; 40,000 rear axles; 365K miles; s/n 2HSCBAXR53C059907.
DUMP & WATER TRUCKS
1989 Mack Econodyne RD 690 S Quad axle dump truck, Mack EM6-300L 300 hp engine; Maxitorque T 2070 7 sp Ext. Range trans; 2 steerable lift axles; 425/65R 22.5 front float tires; 11R 22.5 drive tires; 18’ steel dump body; 446K miles s/n 1M2P198C8KW003979.
1986 International Mod F9370 Eagle tandem axle dump truck; Cat 3406 400 hp engine; Eaton Fuller 15 sp. deep reduction trans; 425/65R 22.5 front float tires; 285/75 R 24.5 drive tires, Northern 22’steel dump box w/ 6’ sides w/ hydraulic end gate; 732K miles; s/n 2HSFBT4R6GCA10317.
1986 Mack RD 685S tandem axle dump truck; Mack 300 HP engine; Maxitorque 7 sp trans; 425165R 22.5 front float tires, 11 R 22.5 drive tires; s/n 1MZP131CIGA011305.
TRAILERS
1999 Benson 48’ x 96” aluminum 10’ spread axle flatbed trailer, air ride; bunks and detchable stakes; s/n INUFT28Z7XMNA0032.
1996 Benson 48’ x 96” aluminum 10’ spread axle flatbed trailer, air ride; bunks and detatchable stakes; s/n INUFT28Z0TMNA0190.
1991 Reinke 48’ x 96” aluminum tandem axle flatbed trailer; s/n IRPFA4828L108.
6 PICKUP TRUCKS
2018 Chevrolet 1500 Silverado LT 4x4 Crew cab pickup truck; 5.3 L engine; 128K miles; s/n 1GCUKREC6JF190145.
2014 Chevrolet 1500 Silverado LT 4x4 Double cab pickup truck; 5.3 L engine; 228K miles; s/n 1GCVKREC7EZ118024.
2012 Chevrolet 1500 Silverado LT 4x4 Ext. cab pickup truck; 5.3 L engine; 138K miles; s/n 1GCRKSE71CZ303503.
2012 Chevrolet 1500 Silverado LT 4x4 Ext. Cab pickup truck; 5.3 L engine; 185K miles; s/n 1GERKSE75CZ181812.
2011 Chevrolet 1500 Silverado LT 4x4 Ext. Cab pickup truck; 5.3 L engine; 203K miles; s/n 1GCRKSE33BZ439935.
2009 Chevrolet 1500 Silverado WT 4x4 Reg. Cab pickup truck; 4.3 L engine; 218K miles; s/n 1GCEK14X59Z179772.
ATTACHMENTS
Rotobec ¼ yd clam dirt bucket.
Prentice log grapple bucket.
Western 7’ hydra turn plow.
4- 18.4 x 26 skidder tires & rims; 2 w/ chains.
4- 700/40-22.5 float tires w/ rims (fits Mack Truck).
Gear Matic Mod. 19 winch.
10,000 GALLON DOUBLE WALL FUEL TANK
B & H Flameshield FS001345 10,000 gallon double wall fuel tank w/ Petro Vend 100 OPW fuel control system, Gasboy Atlas pump; Cox hose reel & hose.
SPECIAL ITEMS
3 – 6' x 10’ single axle trailers ball hitch, equipped with 100 gallon fuel tanks w/ hand pumps; tool boxes.
Miller Big Blue 400 D welding/generator, Duetz diesel engine; mounted on single axle trailer; 1455 hours; s/n F3L912.
Ingersoll Rand 175 portable air compressor w/ Duetz diesel engine.
Briggs & Stratton 3500 watt gen set.
Wacker gen set w/ Honda 5 ½ gas engine.
Tahoe TI 7000 LXR diesel gen set.
Shorelander 2000 lb. aluminum boat lift w/ canopy frame.
4000# Scissor lift.
3 plastic banding carts w/ tools.
Several circle saw blades.
Band Wheel grinding apparatus.
INTERNET BIDDING: If you are unable to attend this auction in person, simultaneous internet bidding is available via Proxibid. A 13% Buyer’s Premium per lot will be added to internet purchases. ONSITE BUYERS: A 10% Buyers Premium per lot will be added to the purchase price.
800-432-1922
715-536-1955
To provide every seller with the service needed to insure their equipment brings top dollar. Specializing in all types of forestry equipment; logging, sawmill, pallet and woodworking plants and equipment.