2006 Polymac LATO 38 Edgebander$15,900

Contact Information

 
  

EX-FACTORY INC.

1805 Sardis Road N
Charlotte, NC 28270
Map ItPrint It

  

Ed Webb

800-374-5009 ext:377

  

View Seller's Entire Inventory and Information

Contact Seller

  
 
 
 
 
   
 
By using this service, you accept the terms of LumbermenOnline.com Visitor Agreement.

Captcha
Click refresh if text is not readable.  
 
Enter the text exactly as it is shown above. 
 
  
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139251.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139252.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139253.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139254.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139255.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139256.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139257.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139258.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=54720&FILE=THMB_EU-0139259.jpg" />


EQUIPMENT DETAILS


  • Year:2006
  • Make:Polymac
  • Model:LATO 38
  • Location:SOUTHEAST,
  • Stock Number:EU-013925

 

EQUIPMENT DESCRIPTION

 

POLYMAC LATO 38 SINGLE SIDED EDGEBANDER8 mm (5/16") Cap. edgebanding thickness, min. panel width 85 mm (w/150 mm panel length) or 50 mm (w/250 mm panel length) & min. length 140 mm, max. panel thickness 45 mm. Automatic strip & coil feed magazine with 3 mm PVC Guillotine (6" pack cap. for strips). Equipped with: Underneath infeed magazine mounted Teflon coated Hot Melt glue pot, Dual digital thermostats, 1" dia. glue applicator roller; Pressure section with (1) large dia. "non-stick" coated drive roller and (2) Pneumatic pressure controlled idle rollers, Horiz. adj. w/ digital indicator. Workstations: Front & Rear end trims (0.5 HP - 12,000 RPM motors), Motors travel on 45° slides and tilt 0° - 12° on horiz. plane. -- Top & Bottom "fine/bevel/profile" multi-function trims (0.73 HP - 12,000 RPM motors), Motors tilt 0° - 30°, Cutters for 10° bevel and 3 mm PVC radius round, digital readouts for easy setup (both T & B trimmes w/Quick Change motors for easy tooling change). -- Top & bottom scrapers for 3 mm thick PVC banding, model "RBD-501" w/ Pneumatic pressure control for scraping knives, digitals for horiz. adjustments; Top & bottom hot air blowers to re-emblish scraper marks; Top & bottom buffing model "SP-500" (0.5 HP - 3,000 RPM motors), units tilt 0° - 30°. -- Feed chain with "anti-slip" 80 mm wide rubber pads, Self-lubrication chain pads, Feed speed 33 FPM, with 2 HP feed drive. Complete with: PLC microprocessor control w/LCD readout, Insulated sound enclosure over all trim stations, Extendable side panel support rail, 4 KVA - 240 Hz digital frequency inverter & complete set of used tooling.

SELLER'S RELATED INVENTORY

Seller Information

 
  


EX-FACTORY INC.

1805 Sardis Road N
Charlotte, NC 28270Map It

  

Ed Webb

800-374-5009 ext:377

View Seller's Entire Inventory and Information