• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
3 Results Found for Router Viewing 1 - 3 of 3 results
RECENTLY ADDED
STANDARD LISTINGS
MULTICAM 3000 SERIES 3-204R 5 X 10 with Multi spindles:60" x 120" Fixed table, moving gantry machine in a front-to-back configuration with a 4 zone vacuum table supported by a (1) 17 HP vacuum system . -- Equipped with:(2) "PERSKE" 4 HP wench type spindles using ER35 collets up to 5/8" with variable speed by inverter from 4,000 up to 24,000 RPM. -- Full table coverage:On X- & Y-axis, rack & pinion gantry drive with brushless Servo motors using integrated 25 mm linear roller bearing rack system, 12" Z-axis travel via lead screw drive with 6" of clearance; 1,000 IPM max. cutting feed, 1,700 IPM max. rapid traverse rate on X- & Y-axis. -- The MULTICAM CNC controller:Is a stand-alone RISC/DSP system. The controller includes a keypad interface with hot keys for repetitious functions and DNC access to host computer. Memory for instant job replay, 32-bit processor, 12 MB RAM & 2 MB flash memory, interprets HPGL and M & G codes, standard ethernet TCP/IP connection for PC communication. -- Includes:17 HP vacuum for hold down and documentation.
Equipment Location:MIDWEST
Norm Schust
800-374-5009 ext:445
MULTICAM 3000 SERIES 3-204R with Tool Changer; 5' X 10' Table: 60" x 120" Fixed table, moving gantry machine in a front-to-back configuration with a multi-zone vacuum table supported by a 35 HP vacuum blower system .Equipped with: -- (1) 10 HP "HSK" spindle with 6-position static tool changer, variable speed by inverter up to 24,000 RPM. -- Full table coverage onX- & Y-axis, rack & pinion gantry drive with brushless Servo motors using integrated 25 mm linear roller bearing rack system, 8" Z-axis travel via lead screw drive. -- 1,000 IPM Max. cutting feed, 1,700 IPM max. rapid traverse rate on X- & Y-axis. The MULTICAM CNC controller Is a stand-alone RISC/DSP system. -- The controller includes a keypad interface with hot keys for repetitious functions and DNC access to host computer. -- Memory for instant job replay, 32-bit processor, 12 MB RAM & 2 MB flash memory, interprets HPGL and M & G codes, RS-232 interface for PC communication. Includes: -- 26.8 kW (35 HP) vacuum blower for hold down, assorted collets and tool-holder will be included. --5 HP Dust collector two bag unit, assorted dust pipe and flex pipe, MultiCam and vacuum pump disconnects and (2) desk top PC's.
Equipment Location:NORTHWEST
Norm Schust
800-374-5009 ext:445
MULTICAM G-204 "Graph-X-Cutter" CNC Knife-Cutting Finishing System:5' X 10' Fixed table, moving gantry machine in a front-to-back configuration with a single zone vacuum table supported by a (1) Vacuum pump System.MultiCam Graph-X-Cutter Registers, Routes, and Cuts with Precision at High Speeds, -- Equipped with: (1) 0.4 HP 23,000 RPM spindle with a tool diameter of up to ¼” (6 mm). You can configure up to 2 tangential knife receivers. You can use just about any type of cutting technique you want (oscillating, ultrasonic, utility, kiss, 45 degree, and more. -- Full tableCoverage on X- & Y-axis, rack & pinion gantry drive with brushless Servo motors using integrated 25 mm linear roller bearing rack system; 5" Z-axis travel via lead screw. -- Feed Rate:1,000 IPM max. Cutting feed, 2,100 IPM max. Rapid traverse rate on X- & Y-axis. The high-torque, brushless AC servo motors used to drive the 3 axes accelerate the gantry. -- The MULTICAM CNCController is the EZ Control a stand-alone RISC/DSP system. -- Controller includes:Keypad interface, hot keys for repetitious functions, and DNC access to host computer. -- Memory for instant job replay32-bit processor, 12 MB RAM & 2 MB flash memory. Interprets HPGL and M & G codes, standard Ethernet TCP/IP connection for PC communication. -- Includes: Vacuum Pump for hold-down, and manuals.
Equipment Location:EASTERN CDN
Norm Schust
800-374-5009 ext:445