You Have Selected

 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
960 Results Found for Woodworking Viewing 1 - 20 of 960 results
RECENTLY ADDED
STANDARD LISTINGS
CEMCO 4352 Wide Belt Sander (3) Heads; -- 52" Width cap. Drum, Drum, Finishing Platen, 3-Head.Head Configuration: -- 1st Head: Steel contact roll, 50 HP motor. -- 2nd Head: Rubber contact drum, 40 HP motor. -- 3rd Head: Finishing Platen, 40 HP motor.Specifications: -- 52" x 103" Abrasive belt. -- Electric eye tracking & air tensioning. -- Variable speed conveyor feed. -- Motorized thickness adjustment from 0" - 6", combination of infeed & outfeed spring shoes & pinch rollers.Equipped with & Features: -- Auto emergency stop, motor load meters, bad belt compensating device, dust tight electrical enclosures, and recent replacement of conveyor belt.
Equipment Location:WEST COAST
Joe Retzlaff
800-374-5009 ext:348
CEMCO URF-2243 Wide Belt Sander (2) Heads43" Capacity Drum, Combination Head. Head Configuration: -- 1st Head: Rubber covered contact roll, 10" dia., 25 HP motor. -- 2nd Head: Combination head with roll and finishing platen, 20 HP motor. Specifications: -- Belt size for 1st and 2nd head: 76" x 43". -- Electronic abrasive belt tracking & pneumatic belt tensioning. -- 2 HP Variable feed speed conveyor motor from 15 - 60 FPM, 0" - 6" motorized thickness cap., infeed & outfeed rubber covered pinch rollers on both heads. Equipped with & Features -- Motor load meters and infeed conveyor extension. -- Air disc brakes on sanding heads. -- Infeed emergency operator stop bar, and (4) dust outlets all 8" diameter.
Equipment Location:WEST COAST
Joe Retzlaff
800-374-5009 ext:348
CEMCO MVB 84 Vertical Boring Machine -- 84" x 24" table with 84" X 24" boring area, 71" between columnEquipped with: -- (6) 1.5 HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- (2) Spring loaded Hold Down -- Moving table with 6" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire mesh
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
Cemco Multi Head Drill, 6 Drill Motors
Equipment Location:South
Mitch Stevens
828-773-6986
78" (2000 mm) Max. between centers, 9.8" round or 7" square (250 mm round or 178 mm square) max. part dia. with revolving steady rest, 6.5 HP main motor, 0 - 4,500 RPM spindle speeds; 0.5 HP hydraulic motor. -- Automatic controlled variable speed carriage with tool post and revolving steady rest, 0 - 32 FPM max. working speed, carriage return speed 33 FPM. -- Special cutting system with: (1) Roughing & (1) finish gouge for simultaneous roughing & finishing, (1) dowel cutting turret knife. Approx (10) follower rings for travelling steady rest. -- Separate control console with: "TRIA 4000" PLC, 720 KB memory, and 3-1/2" floppy disk. Programs for each profile are stored on a disk so there is not need for a template/copy unit. Can control speeds, pauses, up to 10 passes for machining. -- Comes with a Labtop computer with WINDOWS '98 and uses "CT CAD" to generate programs for the profiles. -- Includes: Revolving steady rest, bushes, ball bearing centers; quantities & sizes to be provided. Knife sharpener and a selection of tooling. -- Equipped with: Pneumatic hopper feed and unloading device of finished pieces.
Equipment Location:Midwest
Tony Cornacchione
800-374-5009 ext:432
CENTAURO TA-F-EC Automatic Copy Lathe with (2) Copiers and Hopper Feed.Electronic control of the machine makes it possible to program the complete turning cycle with (1 or 2) passes for fluting & spiral twist in both clockwise/anti-clockwise and cross-milling using the required indexing & pitches.General Specifications: -- 78.7" (2,000 mm) Max. between centers, 10 HP (15 kW) main motor, variable 0 - 4,500 RPM spindle speed; -- 1.5 HP (1.1 kW) Hydraulic power pack for programmable variable speed carriage with an advance rate of 0 - 98 FPM, carriage return speed of 98 FPM. -- Automatic work cycle turning, milling & fluting/spiral twisting for clockwise/counterclockwise and cross-milling with the required depth of pitches and programmable depth of cut. -- Up to (10) pass-depths; can program the complete turning cycle with (1 or 2) passes.Turning Specifications: -- 9-7/8" (250 mm) Max. copying/ milling with round billets and 6.9" (176 mm) with square billets. -- 5-1/2" (140 mm) Max. copying/milling with large steady rest & round billets and 4" (100 mm) with use of square billets. -- 3-1/2" (90 mm) Max. copying/ milling with small steady rest & round billets and 2-1/2" (65 mm) with small steady& square billets.Equipped with: -- Hopper feed, (2) Highly sensitive copying units which can machine simultaneously, with a max. stroke of 6" (150 mm) and (2) revolving steady rests (large or small). -- Hydraulic tailstock with controllable pressure, automatic workpiece centering system inter-linked to tailstock. -- Tailstock sleeve is 60 mm (2-3/8") with 100 mm (4") travel and 3/4" morse taper on tailstock center; hydraulic controlled spindle brake.Milling (Router) Unit consisting of: -- Electric spindle motor, 2.2 kW (3 HP) at 24,000 RPM controlled by "EM22" Electronic Control Unit which can be programed to run at 6,000/12,000/18,000 and 24,000 RPM according to cuttersize. -- The electric spindle has automatic feed and can be programmed up to (10) pass depths. -- Electronic control of the machine makes it possible to program the complete turning cycle with (1 or 2) passes for fluting & spiral twist in both clockwise/anti-clockwise and cross-milling using the required indexing & pitches; milling unit may be removed when not required.Complete with optional: Programmable 2nd automatic pass with a max. depth of 30 mm (1-3/16").
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432

Challoner 71528 Tennoner

Call for Price
Challoner 527 TS Dbl End Tennor w/Controls Serial Number: 403150 Doerr Electric Corp Motor Model: 71528 128/6.4 Amps 3 Phase 220/440 Volts 5 hp 3500 rpm Comes With Transformer and Control Panel Type: 12_4 480 3 Phase Overall Measures 146" Wide X 149" Long X 80" Tall
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
(1) 120" (3,050 mm) x 61" (1,560 mm) Moving "Lignostone" table surface, table is machined with a 30 mm x 30 mm grid with threaded bushings in a 150 mm grid. -- Extra Heavy Duty fixed gantry bridge, X-axis travel is 141.7" (3,600 mm), Y-axis is 62.9" (1,600 mm), and Z-axis is 10" (250 mm). -- Equipped with: (6) 10 HP (7.4 kW) Electro spindle routers with RH/LH programmable rotation, spindle speed of 1,000 - 18,000 RPM, with (6) "piggyback" 4 HP (2.9 kW) spindles powered by (4) 11 KVA frequency inverters. -- Closed loop AC Servo drive system with precision ground ball screws for positioning, very fast 2,125 IPM (54,000 mm) positioning feed rate on X-axis; 1,771 IPM (45,000 mm) on Y-axis, all axes ride on extra large REXROTH (star) precision contour linear guideways. -- "OSAI 10/310" CNC control system with: 420 MB Hard drive, 9" high resolution CRT, RS-232 port built into free-standing control cabinet. -- Featuring: (3) Axes simultaneous control, inch/metric operation, and feed rate & spindle speed override (monitor & controls built into movable pedestal). -- (1) 40 HP TRAVAINI "TRO500S-1A" Vacuum Pump. -- Load & unload system is equipped with: (2) Motorized roller conveyors, (1) motorized belt conveyor. (1) Load & unload device with (2) carriages with vacuum pods; axis strokes are CNC controlled; (1) finished parts unload belt conveyor. -- Min. size of parts 6" (150 mm) x 8" (200 mm); max. size of parts 12" (300 mm) x 30" (760 mm) when manufacturing (6) parts at a time.
Equipment Location:MIDWEST
Norm Schust
800-374-5009 ext:445
CMS PF 111 4 ATC (1) 120" (3,050 mm) x 61.4" (1,560 mm) moving table. -- Lignostone" table surface with (1) vacuum zones table are machined with threaded bushings for use with clamps and fixtures . -- Extra Heavy Duty fixed gantry bridge, X-axis travel = 141.7" (3,600 mm) (head along bridge), Y-axis = 63" (1,600 mm) (table front to back), Z-axis = 9.84" (250 mm). -- Equipped with: (4) 8KW 11 HP Electrospindle with RH/LH programmable rotation, spindle speed of 1,000 - 18,000 RPM, powered by a (2) 22 KVA static frequency converters; routers has a 8-position carousel type ATC allowing "on-the-fly" tool changes (bi-directional). -- Closed loop AC Servo Drive System with precision ground ball screws for positioning, fast 2,125 IPM (54 MPM) positioning feed rate on X-axis; 1,771 IPM (45 MPM) on Y-axis, 393" IPM (10 MPM) all axes ride on extra large Star precision contour linear guide-ways. -- OSAI "10 " Series control system, featuring: (6) Axes simultaneous control, 9" color high resolution TFT, RS-232 port, inch/metric operation, and feed rate & spindle speed override (monitor and controls). -- Complete with: Automatic Centralized Lubrication System with forced grease injection, (2) vacuum pumps. -- Note: Includes extra rebuilt spindle and 35 tool holders. -- Reason for selling this CMS owner is changing to full sheet panel processing.
Equipment Location:PACIFIC NORTHWEST
Norm Schust
800-374-5009 ext:445
CMS PF 102-4T-4M Twin (2) 59" (1,500 mm) x 59" (1,500 mm) Moving tables, "Lignostone" table surface with (2) vacuum zones, tables are machined with threaded bushings for use with clamps and fixtures, can be locked together to form a 59" (1,500 mm) x 120" (3,048 mm) single table. -- Extra Heavy Duty fixed gantry bridge, X-axis travel = 141.7" (3,600 mm) (spindles along bridge), Y-axis = 63" (1,600 mm) (tables front to back), Z-axis = 9.8" (250 mm) . -- Equipped with: (4) 7.5 kW (10 HP) Electrospindle with RH/LH programmable rotation, spindle speed of 1,000 - 18,000 RPM, (4) 4 HP piggyback Electrospindle with RH/LH programmable rotation, spindle speed of 1,000 - 18,000 RPM, All spindles powered by (2) 22 KVA static frequency converter; -- Closed loop AC Servo drive system with precision ground ball screws for positioning, fast 2,125 IPM (54 MPM) positioning feed rate on X-axis; 1,771 IPM (45 MPM) on Y-axis, 393" IPM (10 MPM) all axes ride on extra large Star precision contour linear guideways. -- OSAI "10 310" Series control system, featuring: (8) Axes simultaneous control, RS-232 port, inch/metric operation, and feed rate & spindle speed override (monitor and controls). -- Complete with: Automatic centralized lubrication system with forced grease injection, assortment ETS tool holders with collets, -- Note: Vacuum pumps not included, Y axis on second table has back lash issues.
Equipment Location:EASTERN CDN
Norm Schust
800-374-5009 ext:445
Specs (to be confirmed): Electric spindle 18.1 HP X-axis stroke 145.66î Y-axis stroke 82.67î Z-axis strke 13î Working area 145.66î x 68.90î Automatic tilting head Telescoping spindle extension for surface polishing (26) ISO 40 tool holders at rear Bar code reader for program interface This machine is in good working condition and can be inspected under power.
Equipment Location:CA
Carolina Machinery Sales, Inc
704-288-1904
CNC Auto-Motion XP26 Panel-Master MG 91220 XHDS CNC Router with (4) Axis & ATC: Large Format 9’ x 12’ 4-Axis Flat Table CNC Router, -- Specifications: Moving gantry, fixed table machine with Heavy gauge boxed tubular steel construction, Stress relieved and precision machined for mounting linear rails and rack.X-Axis: 108” (9’), rack & pinion drive, Y-Axis: 144” (12’), rack & pinion drive, Z-Axis: 20” stroke, ball screw drive, A-Axis rotatable 190° from the controller.Features: Thomson Precision 30 mm linear rails, Thomson Precision ball screws, Atlanta helical rack, quenched & tempered, Teco AC servo motors on all axes, 1” (25.4 mm) PVC Matrix vacuum table. -- Spindle:HSD ES919 7 kW (10 HP) ISO-30 router spindle with variable speed 6,000 - 24,000 RPM.Spindle manually rotatable 90° to horizontal; 8-position tool changer magazine rear of table. -- Controller:MachMotion CNC 4-axis closed loop control system X15-100 Computer CPU, Intel 2.0 GHz processor, 160 GB hard drive, 1 GB RAM, Microsoft Windows 7 OS.17” Color LCD flat panel touch screen monitor, retractable keyboard and track ball mouse, Mach3 CNC software, (4) USB ports, 5V and 12V DC power connectors,MachMotion switch panel with hand wheel, E-stop, cycle start/stop, feed rate override, and axis selector. -- Complete with:(2) Shoda/Nishimura "JB-560A" 2 m3/Min, 220V -3 Ph vacuum pumps, assorted tool-holder and documentation.
Equipment Location:WEST COAST
Norm Schust
800-374-5009 ext:445

Coe 249D Veneer Equipment

Call for Price
COE 249D Veneer Lathe with the following: -- LYNDEN Step feeder. -- Small log offset x-y spindle chucks. -- 27" maximum log diameter, 110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling 35 cubic meters per hour. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in excellent condition.
Equipment Location:SOUTHWEST
Bill Christoffersen
800-374-5009 ext:365
COE Model M62, Veneer Roller Jet Dryer fully complete with the following major components and features: -- Veneer Feeder and Unloader, -- 4-Decks, -- 16-Sections, -- Steam heated, -- Half of the Jet Nozzle Boxes have been changed to the M72 style.
Equipment Location:SOUTH
Bill Christoffersen
800-374-5009 ext:365
COMAC C2R160 Top/Bottom Glue Spreader with Semi-Automatic Washing. -- General Specs: 63" width capacity (1600 mm); top & bottom opposed; max.. 2-3/4" opening; 7-1/4" dia. grooved rubber spreading rolls; glue film thickness adjustment via mechanical micro-control of doctor knives on each adhesive tray; galvanized collecting tank; bronze end seals and water tight bearings. --Feed drive: 65 FPM feed speed, 0.5 HP gearmotor feed drive. -- Equipped with: Semi-Automatic Washing System for washing & cleaning glue residue off the rollers; rotating brush travels across rollers washing off glue under rinsing water. Machine connects via hose to water supply, and the runoff to a drainage or container. -- Complete with: (2) Protection safety shields at roller infeed and outfeed; emergency shutoff button; complies with UL & CE safety standards. Machine is mounted on steel casters.
Equipment Location:MID ATLANTIC, AL
EX-FACTORY INC.
704-841-2001
The FAS is a dedicated milling machine with inclinable heads for machining the corner of chair seats. -- Specifications: -- (2) Heads with 5.5 HP motor and 40 mm spindle shaft. -- Maximum cutter size 150 mm (5.9"). -- Tilting of milling units -20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Maximum working height 200 mm (7.8").
Equipment Location:EASTERN CDN
Torry Hiddema
800-374-5009 ext:371
COMEVA MEX VI 13/26 (4-Axis) 4' X 8' with Dual Spindle (opposed) & Boring: The "Dual Spindle" 4th Axis CNC Router makes this one of the most versatile CNC Routers in its class and price range. -- (1,300 mm X 2,600 mm) 4’ X 8’ Phenolic vacuum table with (6) independent vacuum zones and material reference pop up pins. -- All axis run on HIWIN rails with SCHNEIDER servos and contactors -- Spindle: (1) 2.2 Kw (3 HP) with speeds of 6,000 to18,000 RPM (4-Axis) dual main spindle. It allows for (2) different size router bits and can work in any degree in the A-axis rotation meaning you can route vertical (like any standard CNC Router), plus horizontally on any angle you wish. Z-axis stroke 8” (200 mm). -- Boring unit:(1) 9-Spindle arrangement for vertical drilling, plus (3) horizontal for drilling along X-axis and (2) for drilling along Y-axis; l also includes (1) Grooving Saw. -- Control:C-400B- PLC DELTA CNC control is user friendly, works with G & M codes and is well supported. -- Includes:(1) 5.5 kW (7.5 HP) vacuum pump (150 cbm/Hr), UCANCAM V9 software with post processor, and tool touch probe.Covered by 12-months factory warranty.
Equipment Location:MIDWEST
Norm Schust
800-374-5009 ext:445
CONQUEST 2-46 DOUBLE ROW LINE BORER(2) Rows of (23) spindles, drilling depth up to 2-3/8", drills from bottom-up; (2) 2 HP BALDOR motors, 3,450 RPM spindle speed. - Adjustable opening between heads from 5-1/2" - 27" w/mechanical digital readouts. -- Equipped with: (2) Pneumatic holddowns, 132" back fence with (4) large flip stops, (2) air index pins for sequence boring long side panels; table height 37-1/2". -- Complete with: 10 mm Collets, position indicator, air/electrical controls, and foot pedal for clamping & boring cycle.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
2HP Just serviced and ready to work for you Came from small shop, low hours Nice Conquest Boring Machine, reported to be in good condition per the seller
Equipment Location:TN
Carolina Machinery Sales, Inc
704-288-1904
Cornell CLB with 50HP electric Motors running Cutting Mandrels.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351