• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
97 Results Found for Hogs and Wood Grinders Viewing 1 - 25 of 97 results

Chipper-Parts

Wear-Parts

Chainsaw

Mechanical-Harvesters

Chipper-Parts

Marking-and-Tally

Tools

Bits-and-Shanks

Chainsaw

Saw-Grinders
Find More Supplies
STANDARD LISTINGS
Grinder. This machine is an Arasmith 48 x 50 horizonal grinder with 400 hp motor. Item XC498
Equipment Location:Sturgeon Lake,MN
L & L Sales
218-372-4232
ARASMITH Bark Grinder - 45 x 63-1/2 inch top feed opening drum style bark hog. Features 50 inch diameter drum with fixed teeth. Serial HH-1368-692. Top feed, bottom discharge. 20 tons per hour or more capacity. 200-300 HP recommended. see our entire inventory at www.benjones.com
Equipment Location:Columbus,GA
Ben Jones Machinery
706-324-2604
Better Built Bliss Industries Eliminator Swing Hammer Hog 19" x 24" Throat & 2" Screen Holes
Equipment Location:Yuma,TN
LPS Equipment & Acquisition Co.
731-986-4351
Equipment Location:Birmingham,AL
Ellison Sales, Inc.
503-244-0161
Grinder. This machine is a Challenger low speed grinder. Item #C551
Equipment Location:Sturgeon Lake,MN
L & L Sales
218-372-4232
Equipment Location: ,OR
Ellison Sales, Inc.
503-244-0161
Champion Hammer Mill 18"x30" opening, 300 HP Electric Motor, 1/8" Screen Holes, Approx 10 to 12 ton and Hour, Came out of Pellet Mill, 44" Diameter rotor tip to tip Serial # 63065. Parts available through Champion.
Equipment Location:Clarksburg,TN
LPS Equipment & Acquisition Co.
731-986-4351
Cornell Hog, Fair Condition $5000 570-640-7628
Equipment Location:Schuylkill Haven,PA
Reyn Mill Inc.
570-754-7628
Cresswood 2420, 20HP, with infeed conveyor and discharge auger
Equipment Location: ,TX
Ellison Sales, Inc.
503-244-0161
CRESSWOOD Horizontal Grinder - 2007 30 HP low rpm, horizontal grinder with power feed. Features load sensing controls and 15' vibrating infeed conveyor. Located in Florida panhandle. Visit www.benjones.com for our complete inventory.
Equipment Location:Columbus,GA
Ben Jones Machinery
706-324-2604
Cresswood Slow Speed Grinder, 75HP Motor, 1 1/2" Screen Hole Size, Serial # 1050798
Equipment Location:Clarksburg,TN
LPS Equipment & Acquisition Co.
731-986-4351
Equipment Location: ,AR
Ellison Sales, Inc.
503-244-0161
100 HP
Equipment Location:Portland,OR
Ellison Sales, Inc.
503-244-0161
Gruendler Wood Hog •Model 24-3 •Horizontal feed •Serial# 21444, •GE 75HP 220/440 volt 1775 RPM main motor, •Direct drive, 3/4HP infeed motor for feed wheel, •Bottom discharge is 10 inch diameter . •Hammers are 1 1/2 in width. •Rotor width is approx. 24 inches. • Infeed opening is 3 inches tall, infeed opening width 17 1/2 inches. •We can quote you a delivered price to your location. stored inside. motor test available
Equipment Location:Toledo,WA
Machinery Scene
360-864-2800
GRUENDLER MDL 2XB GRINDER W/30HP MOTOR S/N 20847 LPS# 00307
Equipment Location:Yuma,TN
LPS Equipment & Acquisition Co.
731-986-4351
•Jacobson / Carter Day XLT Full Circle Hammermill, •125HP •Reliance XE Energy Efficient Extra Tough direct drive motor •460 volts •1785 RPM •Model # 42315 XLT •Serial# 39960 •1/4 inch thick hammers •Inside width approx. 14 inches •Top Gravity feed • Left side and or right side discharge •Large side access rolling panels for easy rotor and hammer access •Motor starter •Prior use was grinding straw • Stored inside •Motor test available Have a starter that came with Hammermill, but don't know if if works or is the correct size. •Can quote you a delivered price to your location
Equipment Location:Toledo,WA
Machinery Scene
360-864-2800
JACOBSON QUALITY MACHINERY,HAMMER TYPE,125 HP MOTOR, BARN SWEEP UNDERNEATH GOES WITH IT,1 1/2' SCREEN HOLES.
Equipment Location:Yuma,TN
LPS Equipment & Acquisition Co.
731-986-4351
Jeffrey RADER 20 x 25 ESW Chip Feeder
Equipment Location:Yuma,TN
LPS Equipment & Acquisition Co.
731-986-4351
RADER 20 x 25 ESW Chip Feeder with Motor and Drive
Equipment Location:Yuma,TN
LPS Equipment & Acquisition Co.
731-986-4351
Jeffrey 56WB, 400HP, super rotor with 160 pound hammers
Equipment Location: ,OR
Ellison Sales, Inc.
503-244-0161
Jeffrey Oregon Industrial Model 34WBSS, 200HP Motor, 22" x 34", S/N 071808
Equipment Location:Clarksburg,TN
LPS Equipment & Acquisition Co.
731-986-4351
JEFFREY 30 WB Wood and Bark Hog - top feed, bottom discharge wood hog. Includes 60 HP motor and feed chute. Mississippi. see our entire inventory at www.benjones.com
Equipment Location:TYLERTOWN,MS
Ben Jones Machinery
706-324-2604
Jeffery 34 WB Hammer Hog w/ infeed Chute & Base (no grates)
Equipment Location:Clarksburg,TN
LPS Equipment & Acquisition Co.
731-986-4351
Hog. This machine is a Jeffrey Hog with 125hp motor with top shroud and extra hammer. Item #00550
Equipment Location:Sturgeon Lake,MN
L & L Sales
218-372-4232
Jeffrey Size 45 Hammer Mill Serial# 11142, Slotted Screen.
Equipment Location:Clarksburg,TN
LPS Equipment & Acquisition Co.
731-986-4351