• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
2 Results Found for Tennoner Viewing 1 - 2 of 2 results
STANDARD LISTINGS
FLETCHER FM-200S Single End Shape & Sand --60 in. infeed x 12 in. fixed opening,Equiped with: -- 12 in. wide feed-chains. Snap-in Dogs on 10" centers, at ¼ in. high on inside of chains. -- Stations 1-2: -- Top and bottom tilting tenon heads with 10 HP, 3,600 motors. -- Arbors 35mm diameter x 5-3/8 in. long with threaded lock nuts. -- Max. diameter of cutter-head 12". -- Tenon heads are mounted on dovetail slide affixed to a cast iron column with dovetailed slides that allow vertical and horizontal adjustments.with digital readouts -- This station includes off-set tilting. -- Station 3: -- High speed tilting shaper head driven by 10HP, 7,200 RPM. -- Max. diameter of cutter-head 10" -- Shaper is mounted on dovetail slide and provides both vertical and horizontal movement. with 2-axis electronic digital read-outs, electronic motor brake and tilt. -- Wall mounted 12 in. long polished anvil with height and tilt adjustments. -- Sound and dust enclosure for: Stations 1-3 -- Each tool station is guarded and provided with individual dust extraction.Stations 4-6: -- Composite tilting disc sanding stations driven by 2HP motors with AC variable speed from 300-2,400 RPM. -- 1-1/4". diameter spindle mounted on dovetailed castings for vertical and horizontal adjustments. equipped with (2)-axis digital read-outs and reversing. -- Auto indexing of sanding wheels controlled by lineal counter. -- Outboard stock supports and piece counter. MAlso included: -- Air table top assembly (vacuum top) drop to a 30in. -- Hytrol return conveyor (1HP)Note:ALL FRICTION PADS ON THE MACHINE WILL BE REPLACED UPON PURCHASE ORDER
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
FLETCHER FM 200S Single End Tenoner -- 60" infeed x 12" fixed opening, 12" wide feed chains with urethane pad tops -- Snap-in dogs on 10" centers, 1/4" high on inside of chains (dogs not included)Equipped with: -- Station 1: 10 HP 3600 RPM top and bottom tenon units. Arbors are 35 mm keyed diameter x 5-3/8" long with ends of arbors threaded for locking nuts, maximum diameter of cutterhead is 12" to fit inside of guard, includes offset tilting and 2-axis digital readouts -- Station 2: 10 HP 7200 RPM high speed shaper unit (gearbelt driven to 7200 RPM), Spindle is 35 mm keyed with maximum diameter of 10" to fit inside of guard, Includes 2-axis digital readout, electronic motor brake, and tilting -- Station 3: 2 HP abrasive sanding wheel with AC variable speed 600 to 1800 RPM, auto index, 2-axis digital readout, reversing, and 1-1/4" arbor -- Station 4: 2 HP abrasive sanding wheel with AC variable speed 600 to 1800 RPM, auto index, 2-axis digital readout, reversing, and 1-1/4" arbor -- Station 5: 2 HP abrasive sanding wheel with AC variable speed 600 to 1800 RPM, auto index, 2-axis digital readout, reversing, and 1-1/4" arbor -- 7.5 HP variable speed feed Automatic lubrication of feed chain -- Tenon machine link type holddown with double width rubber blocks -- Sound/safety enclosure around tenon and shaping units with internal lighting --Separate electrical panel -- Machining on the right side of infeed -- Outboard stock support- rollers on 2" centers -- Piece counter -- Return transfer conveyor (belt return section) Manual drop off at the machine exit -- (3) 4" dia. dust outlets and (3) 6" dia. dust outletsNote: no tooling or abrasives included
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329