You Have Selected

 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
986 Results Found for Woodworking Viewing 1 - 20 of 986 results
RECENTLY ADDED
PREMIUM LISTINGS
DeWalt/Black & Decker 3553 7.5 hp 3-phase radial arm saw. Purchased after overhaul from factory in Britt, IA. Has plastic all-weather cutting deck. Have particle board cutting deck. Comes with accessory rollers for long pieces of wood. Stored inside and ready to go.
Equipment Location:Anselmo, NB
308-289-5466
STANDARD LISTINGS
CASADEI F-114 Shaper with 5 HP Spindle motor and Power Feeder. -- 1-1/4" dia. spindle, 7" spindle length, 8-1/2" vertical travel, manual raise/lower of spindle, numerical readout display for spindle setting. -- (4) speeds at 2,900 - 4,400 - 6,000 & 8,000 RPM, electro-magnetic spindle brake. -- 43" x 28" table size, adjustable fence (360ø rotatable) with (3) micro-metric fine adjustments. -- Complete with: Overload protection, electric spindle lock, and Power Feeder
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
CASATI TOP 4000 Heavy Duty Veneer Guillotine, Single Knife. -- Capacity: 157" (4,000 mm) Cutting length, 3.94" (100 mm) cutting height, 39.3" (1,000 mm) max. cap. 1" (25.4 mm) min. rear feed. Motorized rear fence with digital readout and hand wheel fine adjustment. -- Motors: Separate hydraulic power packs (1) for knife and (1) hydraulic power pack for overhead presser beam. 12 HP knife gearmotor drive. 4 HP hydraulic power pack for overhead pressure beam. 1 HP rear fence gearmotor. Knife mechanically operated. Hydraulically operated brake. --Features: Torsion bar keeping pressure beam parallel. -- Complete with: 24" x 84" Rear support table area Double palm push buttons, photo cell safety lights and pressure gauge. Separate hydraulic controls for knife and for pressure beam. Manual/Auto work cycles. Total installed power 18 HP (13.5 KW). Weight 16,500Lbs.
Equipment Location:SOUTHWEST
Tony Cornacchione
800-374-5009 ext:432
126" (3,200 mm) Cutting length, 3.94" (100 mm) cutting height, motorized back fence from 1" - 31-1/2" cap. fence travels on hardened ways, 0.5 HP motor, LED readout for fence positioning & fine adjustment by front mounted hand wheel. -- Equipped with: Hydraulic pressure beam-and-knife powered by 10 HP hydraulic pump motor, 6" wide pressure beam with cutting force adjustment for beam-and-knife, beam assembly with self-lubricated slide ways. -- Complete with: Cutting line with 4-side plastic cutter counter gib, cutting edge light for material positioning, 2-hand push button operation for safety; features operation selection for manual & automatic working cycles.
Equipment Location:EASTERN CDN
Tony Cornacchione
800-374-5009 ext:432
CEHISA PRO 12 ... Edgebander with Pre-Milling & Corner Rounding.Features & Working Capacity: -- Specifications: 0.4 - 5 mm (3/16") max. edge thickness cap., min. panel width 75 mm (3"), panel thickness min/max. 8 - 40 mm (5/16 - 1-5/8"). -- Pre-Milling Station with: 2 x 1.5 Kw (2.0 HP) 12,000 RPM motors, standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System, MR-5: 10 - 15 min. heat-up time, auto temperature drop. Glue Tank is coated with nonstick material, quick-change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital read-out and pneumatic positioning selectable from controller touch screen.Edgebanding Workstations: -- End Trimming Station, V-4: Double motor front & rear, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM. -- Edge Trimming Station, JC-5: Top & bottom flush/bevel/radius trimming, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM, tiltable 0ø - 20ø, pneumatic exclusion from operator panel. -- Corner Rounding Unit, CR-1: To process overhanging edges and trimming around the leading & trailing edge, 1 x 0.27 Kw (0.36 HP). -- Profile Scraping Unit, RB-8: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper, RR-7: To remove potential glue squeeze-out. -- Buffing Unit, PC-9: Top/Bottom, 2 x 0.12 Kw (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically.Controller: -- PLC Microprocessor control with color touch screen, memory up to 20 programs.Equipped With: -- Feed Speed, 10 & 16 MPM (35 & 55 FPM), -- Power hold-down beam, work-piece support outrigger, safety & sound enclosure.Included Options: -- Riepe, non-stick spray system -- Nesting Tracer Shoes for top/bottom trimmers
Equipment Location:MIDWEST
Karl Balg
800-374-5009 ext:355
CEHISA EP-8 Single sided Edgebander3/16" Cap., Min. panel size: Length 4-3/4", width 3" and thickness 3/8" up to 2", unlimited max. length & width. -- Equipped with: -- Automatic strip feed & coil feed magazine, -- Compact Hot Melt glue system, heats up in (7 - 10) Min, -- 2.5 mm PVC guillotine, 3-roll pressure section with (1) drive & (2) idle rollers. -- Workstations: -- Single motor (0.33 HP - 12,000 RPM motor) end trim with (2) blades; -- Top & bottom flush & bevel trim unit (0.75 HP ea. motor), tilts 0ø - 20ø; -- Top & bottom buffing unit (0.75 HP motors). -- 2 HP Feed drive for feed speed of 33 FPM. - Complete with: Digital counters, sound enclosure, outboard panel support, frequency converter, and used tooling.Seller says he heating elements require repair and all else works fine.
Equipment Location:SOUTHEAST
Ed Webb
800-374-5009 ext:377
CEHISA EP-C Contour Edgebander;Designed for edgebanding & trimming straight, round, & free shaped panels.Specifications & features: 1/8" (3 mm) Max. edge cap., 3/8" to 2-1/4" panel thickness, min. edgebanding radius is 13/16", min. part length 11"; compact in table Hot Melt glue pot, automatic coil infeed. -- Variable feed drive to glue/pressure roller; manual feeding of panel governed by variable speed of 1-3/4" dia. silicone covered drive roller, dial-in counter end cutoff for coil material; foot pedal control to advance edgebanding. -- Equipped with: Panel support extension, table tilts 0° - 45° for bevel edging; digital thermo-control for glue temperature; operator control panel under the table at knee-level for easy access while running materials.
Equipment Location:SOUTHEAST
Ed Webb
800-374-5009 ext:377
CEHISA BRYKO, Single Sided Edgebander0.4 - 2 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 2 mm thick PVC.Features: -- Integrated Operator PLC controls for (10) programs, "short-cut" function keys and an LCD display.Workstations: -- Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Single feed speed of 20 FPM. -- "Anti-slip" rubberized surface chain pads.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support. -- Set of tooling and operator's and spare parts manual.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
CEHISA EP-9 Single Sided Edgebander0.4 - 6 mm Banding capacity, automatic strip feed & coil feed magazine, compact Hot Melt glue system, heats up in (12) Min.Specifications: 3 mm PVC Guillotine, 3-roll pressure section w/pneumatic positioning; min. panel length 5" (120 mm), min. panel width 3" (75 mm), max/min panel thickness .375" - 2" (8 - 45 mm).Workstations: -- Single-motor end trim with (2) blades. -- Top & Bottom flush & bevel trim unit with 0° to 20° tilt (0.75 HP ea. motor). -- Top & bottom PVC scraper for up to 3 mm radius. -- Last Station: Top & bottom buffing unit (0.75 HP motors).Features: Electronic braking on trim motors; digital readout on top/bottom trim; feed speed of 35 FPM and 2 HP feed drive.Complete with: SIEMENS "Simatic" touch screen control; Sound enclosure; outboard panel support; frequency converter; used tooling.
Equipment Location:SOUTHEAST
Ed Webb
800-374-5009 ext:377
CEHISA "EP-9" SINGLE SIDED EDGEBANDER0.4 - 6 mm Banding capacity, automatic strip feed & coil feed magazine, compact Hot Melt glue system, heats up in (12) Min.Equipped with: -- 3 mm PVC Guillotine, 3-roll pressure section w/pneumatic positioning; min. panel size: 4-3/4" Length x 3" width x 8 - 45 mm thickness.Work Stations: Single-motor end trim with (2) blades -- Top & Bottom flush & bevel trim unit with 0° to 20° tilt (0.75 HP ea. motor). -- Top & bottom PVC scraper for up to 3 mm radius. -- Top & bottom buffing unit (0.75 HP motors). -- Electronic braking on trim motors; digital readout on top/bottom trim; feed speed of 35 FPM and 2 HP feed drive. -- Sound enclosure, outboard panel support, frequency converter, and used tooling.
Equipment Location:NORTHEAST
Ed Webb
800-374-5009 ext:377
CEHISA "PRO 8" SINGLE SIDED EDGEBANDER0.4 - 3 mm Edge thickness cap., Teflon coated glue pot system, automatic magazine for strip & coil feed; Heavy Duty guillotine for up to 3 mm thick PVC. Specifications: (2) roll pressure zone with (1) motorized and (1) idle roller. -- Workstations: Single motor saw blade end trim (0.45 HP - 12,000 RPM motor); Top & bottom flush/bevel trim, bevels 0° - 20° (0.45 HP motor ea.) -- (2) Motor Top & Bottom Buffing station. -- Complete with: High Frequency converter, 1 HP main drive motor, digital readouts for trimmer adjustments, sound hood & tooling.
Equipment Location:SOUTHWEST
Ed Webb
800-374-5009 ext:377
CEHISA 404 SINGLE SIDED EDGEBANDER0.4 - 20 mm (3/4") Edge thickness cap. and also 5 mm PVC banding,Edgebanding height 2.36" (60 mm) max: 5" min. panel length and 3" min. width.Equipped with: Quick Melt compact glue system, automatic strip & coil magazine, guillotine for up to 4 mm thick PVC; 4-roll pneumatically controlled pressure section, each roller individually controlled.Workstations: -- Double motor end-trim (0.75 HP HF motors), tilt 0° - 10°;. -- Top & bottom flush trim (2 HP - HF motors). -- Top & bottom radius scrapers for 3 mm PVC. Top & bottom buffing (0.75 HP motors ea.). -- Variable feed speed from 30 - 72 FPM, 2.5 HP feed drive.Complete with: Sound insulated enclosure w/windows, outboard panel support, and used tooling.
Equipment Location:WEST COAST
Ed Webb
800-374-5009 ext:377
Grecon Dimter Lateral Infeed on raised stand.
Equipment Location:NC
Carolina Machinery Sales, Inc
704-288-1904
CEHISA BRYKO PLUS, ..."Compact" Edgebander. 0.4 - 2 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length. -- Equipped with: Quick Melt Teflon coated glue pot for granular hot-melt adhesive; Heavy Duty guillotine for up to 2 mm thick PVC. -- Features integrated Operator PLC controls for (10) programs, "short-cut" function keys and a LCD display.Workstations: -- Double Blade End Trim with HF motor - 12,000 RPM; Top & bottom flush/bevel trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM ea.); -- Top & Bottom PVC Scraper for up to 5 mm radius. -- Single feed speed of 20 FPM and "anti-slip" rubberized surface chain pads. -- Complete with: Sound & Safety enclosure over trim stations and outrigger panel support. -- Includes set of tooling and operator's and spare parts manual.
Equipment Location:MID ATLANTIC
Ed Webb
800-374-5009 ext:377
CEMCO MVB 84 Vertical Boring Machine -- 84" x 20" table with 84" X 15" boring area, 71" between columnEquipped with: -- (6) 1. HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- Moving table with 8" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire meshNote: Picture of the machine are before it will be cleaned and checked
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
CEMCO MVB 84 Vertical Boring Machine -- 84" x 20" table with 84" X 15" boring area, 71" between columnEquipped with: -- (5) 2. HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- Moving table with 8" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire mesh
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
CEMCO URF-2243 Wide Belt Sander (2) Heads43" Capacity Drum, Combination Head. Head Configuration: -- 1st Head: Rubber covered contact roll, 10" dia., 25 HP motor. -- 2nd Head: Combination head with roll and finishing platen, 20 HP motor. Specifications: -- Belt size for 1st and 2nd head: 76" x 43". -- Electronic abrasive belt tracking & pneumatic belt tensioning. -- 2 HP Variable feed speed conveyor motor from 15 - 60 FPM, 0" - 6" motorized thickness cap., infeed & outfeed rubber covered pinch rollers on both heads. Equipped with & Features -- Motor load meters and infeed conveyor extension. -- Air disc brakes on sanding heads. -- Infeed emergency operator stop bar, and (4) dust outlets all 8" diameter.
Equipment Location:WEST COAST
Joe Retzlaff
800-374-5009 ext:348
CEMCO MVB 84 Vertical Boring Machine -- 84" x 24" table with 84" X 24" boring area, 71" between columnEquipped with: -- (6) 1.5 HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- (2) Spring loaded Hold Down -- Moving table with 6" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire mesh
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329

Cemco U002252 Sander

Call for Price
Cemco Orbital Sander Model U002252, S/N 05109, 675Hours
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
CEMCO 4352 Wide Belt Sander (3) Heads; -- 52" Width cap. Drum, Drum, Finishing Platen, 3-Head.Head Configuration: -- 1st Head: Steel contact roll, 50 HP motor. -- 2nd Head: Rubber contact drum, 40 HP motor. -- 3rd Head: Finishing Platen, 40 HP motor.Specifications: -- 52" x 103" Abrasive belt. -- Electric eye tracking & air tensioning. -- Variable speed conveyor feed. -- Motorized thickness adjustment from 0" - 6", combination of infeed & outfeed spring shoes & pinch rollers.Equipped with & Features: -- Auto emergency stop, motor load meters, bad belt compensating device, dust tight electrical enclosures, and recent replacement of conveyor belt.
Equipment Location:WEST COAST
Joe Retzlaff
800-374-5009 ext:348