• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
2 Results Found for Edgebander Viewing 1 - 2 of 2 results
RECENTLY ADDED
STANDARD LISTINGS
BIESSE STREAM B1 9.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge thickness cap. 0.01' - 0.8" (0.3 - 20 mm), min. panel width 2.5" (65 mm), panel thickness 0.4" - 2.4" (10 - 60 mm), min. panel length 6" (150 mm). Automatic (2) coil vertical feed magazine for coil material up to 3 mm thickness with automatic changeover. Patented glue system w/pre-melt, large separated granular hopper for easy filling & high gluing capacity,Reversible roller applicator with (1) large driven pressure roller & (6) pneumatic secondary pressure rollers. -- Operator & Machine Control: "NC 410" Controller with: Graphic interface on MS-Windows 2000 Professional, 32-bit operating system; high resolution LCD color screenUnlimited" number of working programs, each with functions for remote control of processing units; fault diagnostic, bar code reader adaptable; etc. Workstations: -- Pre-Milling Unit:With jump control & side copying unit for managing warped panels, 2-position infeed fence, digitals readouts. -- End Trimming:Double motor front & rear linear end trimming unit "IT 46" (0.4 HP/0.3 kW - 12,000 RPM motors ea.); pneumatic chamfer setting, 0° - 15° adjustable. -- Pre/Rough Trimming:Top & bottom "RS 10" (1.75 HP/1.3 kW - 12,000 RPM motor ea.), pneumatic exclusion & positioning from control panel. -- Radius/Bevel Trimming:Top & bottom (0.87 HP/0.65 kW - 12,000 RPM motor ea.), tiltable 0° - 30°, pneumatic exclusion from operator panel. -- Corner Rounding:4-Motor for leading & trailing edges. -- Profile Scraping Unit: Top & bottom with collection box. -- Flat Glue Scrapers:Top/bottom to remove potential glue squeeze-out. -- Buffing Unit:Top/bottom, ozcillating/tilting "SZ 30" w/pneumatic exclusion control from control panel & 0.67 HP/0.5 KW - 1,400 RPM motors; -- Hot Air Unit:Top/Bottom hot air blowers to reactivate/smooth heavy pvc radiused edges. -- Complete With:Motorized top pressure beam with powered V-belt holddown, 80 mm wide Heavy Duty feed chain w/rubber pads, 4 HP (3 kW) feed drive for feed variable speeds of 33 - 79 FPM (10 - 24 MPM). Electronic positioning by NC controller with Pneumatic Pre-set Stop System for most adjustments via the control panel on top & bottom trim, fine trim, and scraper station, electronic frequency inverter,Electronic DC brakes on all trim motors, sound cabins for all trim work stations, outboard panel support,
Equipment Location:NORTHWEST
Karl Balg
800-374-5009 ext:355
BIESSE STREAM B1 7.5 ... EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge thickness cap. 0.01" - 0.8" (0.3 - 20 mm), min. panel width 2.5" (65 mm), panel thickness 0.4" - 2.4" (10 - 60 mm), min. panel length 6" (150 mm). -- Front-End Configuration:Pre-Milling Unit. With jump control & side copying unit for managing warped panels, 2-position in-feed fence, digitals readouts.Pre-heating Section, infra-red, top & bottom lamps to pre-heat the panel edge.Edge Magazine, automatic (2) coil vertical for coil material up to 3 mm thickness with automatic changeover. Solid Wood Edge Kit for up to 20 mm (3/4") thick straight edge-strip processing.Glue System (SP20) EVA (Hot Melt) patented w/pre-melt, large separated granular hopper for easy filling & high gluing capacity,reversible glue roller applicator.Side Pressure Section, (1) large inverter driven roller and (6) idle pressure rollers. servo motor, programmable positioning.Operator & Machine Control: -- "NC 410" Controller With: Graphic interface on MS-Windows XP Professional , 32-bit operating system; high resolution LCD color screen unlimited" number of working programs, each with functions for remote control of processing units; fault diagnostic, bar code reader adaptable; etc. Workstations: -- End Trimming (IT90-S):Double motor front & rear linear end trimming unit (2 x 0.4 HP/0.3 kW - 12,000 RPM motors ea.); pneumatic chamfer setting, 0° - 25° adjustable. -- Pre/Rough Trimming (RS10):Top & bottom "RS 10" (1.75 HP/1.3 kW - 12,000 RPM motor ea.), pneumatic exclusion & positioning from control panel. -- Radius/Bevel Trimming (RF40):Top & bottom (0.87 HP/0.65 kW - 12,000 RPM motor ea.), servo motor positioning allowing multi profile use, pneumatic exclusion from operator panel. -- Corner Rounding / Multi Function Trimming Unit (AR34) :4-Motor for leading & trailing edges and or linear fine trimming. Automatic (2) position pre-sets, i.e. thin or 3 mm thick edge materials. Automatic pneumatic exclusion if not used. -- Profile Scraping Unit (RBK-503):Compact top & bottom with (2) programmable position and collection box. -- Flat Glue Scrapers (RC20):Top/bottom to remove potential glue squeeze-out. -- Buffing Unit (SZ30):Super imposed top/bottom, oscillating/tilting w/pneumatic exclusion control from control panel & 2 x 0.67 HP/0.5 KW - 1,400 RPM motors; -- Hot Air Unit (PG-700):Top/Bottom hot air blowers to reactivate/smooth heavy pvc radiused edges. -- Complete With:Motorized top pressure beam with powered V-belt holddown, 80 mm wide Heavy Duty feed chain w/rubber pads, 4 HP (3 kW) feed drive for feed variable speeds of 33 - 82 FPM (10 - 25 MPM). Electronic positioning by NC controller with Pneumatic Pre-set Stop System for most adjustments via the control panel on top & bottom trim, fine trim, and scraper station, electronic frequency inverter,Electronic DC brakes on all trim motors, sound cabins for all trim work stations, outboard panel support,Actual Machine Model: ... STREAM
Equipment Location:SOUTH
Karl Balg
800-374-5009 ext:355