TAYLOR - 20-Section, ...Manual Clamp Carrier• 8' Width cap., approx. (6) clamps per section (108 clamps total).• 32" Max. clamp opening, (120) clamps with 2-1/2" jaw height.Complete with:Pneumatic air drive carrier rotation. -- Manual tightening. -- No panel flattener.

TAYLOR 20-Section Clamp Carrier Specifications: -- 10.5' Width cap. -- 40" Max. clamp opening, 2-1/2" Jaw height. -- (6) clamps per sectionEquipped with: -- (120) Clamps total. -- Pneumatic tigthener -- Pneumatic panel flattenerComplete with: -- Air drive carrier rotation, -- I-Beam chain assembly.

TAYLOR 40 Section Clamp Carrier.Specifications: -- 40-Section, 8-1/2' width capacity -- Average 4/5 clamps per section (175 clamps total), all with 32" max. clamp opening. -- Equipped with (175) clamps plus a pallet of spares that require repair, 32" clamps with 2-1/2" high jaws .Complete with: -- Heavy Duty Drive for rotation,& clamp tightening. -- Foot pedal control. -- Includes a glue applicator.

TAYLOR - 40-Section, ...Clamp Carrier -- 10-1/2' Width cap. -- (240) Clamps total -- 32" Max. clamp opening with 3-1/2" high jaws. Complete with: -- Pneumatic panel flattener -- Pneumatic rotation -- 48" Plate spreader New in 2016Note: Tear down not included.

---In Auction---Complete w/ 71 Clamps!--- TAYLOR 800036 7' W 12-Section Semi-Automatic Pneumatic Clamp Carrier, with Flattener & Tightener Equipped with: - (71) 32” Cap. Clamps, with 4-5/8” W x 3-1/2” H Jaws. - Air motor drive. - Dual foot pedal control. Complete with: - Pneumatic Panel Flattener. - Pneumatic Clamp Tightener. Details, Photos, Videos, Bidding: https://exfactoryauctions.com/Detail/CR-230064/event/A051324$1

TECNOMA - XT10.3 RS, ...Single Sided Edgebander.5/16" (5 mm) Max. edge cap., 1-1/2" (40 mm) max. banding height, 2-3/8" (60 mm) min. panel width, and 5-1/2" (140 mm) min. length. Equipped with: -- Automatic coil feed magazine with semiautomatic feed for strips, -- Teflon® coated glue pot (Heat up time 8 Min), -- Heavy-Duty 3 mm PVC capacity guillotine, 2-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning; 2nd roller idler roller. Workstations: -- Double motor front & rear end trim (0.41 HP - 12,000 RPM motor ea.), tilts 0° - 15°; end trimmer mounted on 45° THK guides. -- Top & Bottom flush trims (0.46 HP - 12,000 RPM motor ea.), equipped with "Quick Release" electric connectors for easy swap out of trim motors/tooling. -- Last Station: Top & Bottom buffing unit (0.2 HP - 2,750 RPM motor ea.), both adjustable. -- Single 26 FPM fixed feed speed, 0.8 HP feed drive. Complete with: -- Sound-proof enclosure, "Special" 70 mm wide chain pads, (2) rows of upper pressure wheels (60 mm dia. ea.) with "ball bearings" (vs. bushings) for long production life.

TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

TIGER-TEC Rotary Vane Vacuum Pump:7 HP Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 82 CFM with max. 23.6"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve with canister filter, motor speed of 1,440 RPM, 220V, 3phase, weight 133kg (293lbs)dimensions: 39"L x 18"W x 24"H

TIMESAVERS 137-1 SINGLE HEAD WIDE BELT SANDERSpecifications: -- 36" Width capacity, combination sanding head with 6" dia. spiral grooved rubber contact roll. -- 1-1/2" Wide adjustable height polishing platen on slide out assembly. -- 37" x 60" Abrasive belt size.Equipped with: -- 20 HP Main motor, -- Electric eye abrasive belt tracking, and limit switch monitoring. -- 1 HP feed motor with a fixed speed of 30FPM. -- 0" - 8" manual part thickness opening of conveyor bed. -- Double infeed & outfeed rubber covered holddown rollers. Complete with: -- 18" Infeed conveyor extension, motor load meter, and safety stop bar.

TIMESAVER - 113, ...12" Width Single-Head Wide Belt Sander12" Width cap., single drum.Specifications: -- 12" Width capacity. -- 7.5 HP Main motor. -- 6" Dia. drum. -- 0 - 8" Opening capacity. -- 0.5 HP Feed motor. -- Complete with: Posi-Trac electronic tracking and a 12" conveyor extension.

TIMESAVERS 150-1v Wide Belt Sander;1-Head, 50" width cap.; contact roll head with 40 HP motor; 50" x 103" abrasive belt size, air tracking, 2-1/2" max. thickness cap., adjusted by scale; variable feed speed 40 to 100 FPM; incl. in- & outfeed extension. -- Used to have a checkrail edge sanding attachment for sanding sash (no longer available), but includes (1) extra set of new conveyor belts.

TIMESAVERS 137-2HD Double Head, 36" Wide Belt Sander. 2-Head, 36" width cap.Specifications: -- 1st Head: 6" Dia. rubber-covered contact roll, 25 HP motor; -- 2nd Head: 2-1/2" Wide finishing platen, 15 HP motor. -- 37" x 60" Abrasive belts, "Posi-Trak" electronic tracking & pneumatic tensioning, 15 - 45 FPM variable feed speed. Equipped with: -- Double infeed & outfeed spring loaded holddown rolls, 0" - 8" max. manual part thickness opening with mechanical digital readout, air-operated disc brakes, motor load meters. -- 21" Infeed conveyor extension, and infeed emergency stop. -- Includes: (1) Extra rubber covered roll, (1) pipe, (1) Elec. disconnect.

TIMESAVERS - 237-2, ...2-Head Wide Belt Sander36" Width capacity; Drum, Drum.Head Configuration:1st Head: Steel contact roll, 9-1/2" dia., 25 HP motor.2nd Head: Rubber covered roll, 9-1/2" dia., 20 HP motor.Specifications: -- 37" x 75" Abrasive belts. -- Motorized part thickness adjustment with mechanical digital readout, 0" - 6" opening. -- Infeed & outfeed spring-loaded holddown rolls and shoes. -- 15 - 45 FPM Variable feed speed. Equipped with & Features: -- Motor load meters. -- Infeed emergency stop bar. -- Disc brakes on sanding head motors. -- 24" Infeed load area.

WEINIG Powermat 1000 7-Head Feed Trough Moulder(B-R-L-T-T- B-U); working cap. 9-1/16" x 4-3/4". Head sequence: -- Bottom 15 HP, Right 15 HP, Left 15 HP, Top 30 HP, Top 40 HP , bottom 30 HP and universal 15 HP motor. All motors with electronic brakes. WEINIG Touch-Screen "Power Com" -- PowerCom Plus software system features: Profile drawing storage, profile dimensions, tool changes and production optimization. -- Electronic LED readouts for all tool holder settings, including chip breakers & pressure elements. -- Spindle #1: 1-13/16" w/Cutterhead speed of 8,000 RPM; -- PowerLock tool holders on #2 - #5 with 12,000 RPM and universal tool holder variable from 4,000 to 12,000 RPM and with high precision bearings; adjustment of vertical tools 2-3/16" axially. -- Motorized tool positioning; radial & axial on tool holders #2 - #5; motorized feed beam adjustment with independent adjustment top head; top head with independent adjustment of chip breaker & pressure element. -- Universal spindle with 270° of movement. -- Variable feed speed from 20 - 118 FPM, 7.5 HP inverter controlled Cardan feed drive, overhead feed wheels with pneumatic pressure. -- Vertical tools with adjustable table plates to cutting circles, hardened infeed bed plates before & after 1st bottom head. -- Chromed tables and fences, (2) powered table rollers in bed and (1) between left and top spindles and (1) at outfeed. -- Infeed straightening table 2 M (6-1/2').Equipped with: Pedestal for machine controls separate from the electrical cabinet, central location of lubrication points. -- Electromagnetic interlocking of safety hood, automatic table lubrication pump and (2) lights inside reinforced sound enclosure; phone modem..

WENIG PROFIMAT 23E Feed Through Moulder5-Head (B-R-L-T-B), working cap. 9-1/16" x 4-11/16".Specifications: -- Spindle Sequence: Bottom 10 HP, Right & Left by 15 HP, Top 15 HP and Bottom 10 HP motor. -- Spindles: 1-1/2" diameter. with cutterhead speed of 6000 RPM. -- Digital Readouts: "DigiSet" digital readouts for chipbreaker and pressure element at top spindle -- FPM: Variable feed speed from 17 - 78 FPM, powered by a 4 HP motor -- Safety: Full enclosure sound proof booth -- Receding chipbreaker & pressure element at top spindle -- Rollers: Side pressure opposite right spindle, spring loaded with 2 rollers and driven outfeed roller in bed. -- Infeed straightening table 2 meter (6'6") -- Features central lubrication system via manual table lubrication pump. -- Machine is wired for 460 Voltage / 3 Phase Power using 79 Full Load Amps. -- Includes - All heads, rollers, setup tools shown are included, Owner's Manual, and 4-hose Dust manifold.This machine runs perfectly, is in Good Condition- with some dents to the outer sound enclosure. Overall Dimensions: 132"; x 64"; x 64";Approx. 8,000LBSRemoval is responsibility of buyer. Seller can build a crate, and put it on a truck for an additional $1,000.00

WEINIG UNIMAT 818 S Feed Through Moulder 6-Head (B-R-L-T-T-B), working dimension 12-3/16" x 6- 5/16".Capacity: -- Working width 3/4" - 12-3/16" -- Working thickness 5/16" - 6-5/16" -- feed speed-variable with 10 HP inverter 20 - 200 FPM Head sequence: -- Bottom 25 HP, right 15 HP, left 15 HP, top 30 HP, top 30 HP, and bottom 30 HP motor; all motors with electronic spindle brakes. -- Spindle dia. 1-13/16" with cutter head speed of 6,000 RPM; -- outboard bearings on spindles #1, #4, #5 & #6. Electronic LED digital readouts for all spindlesJointer: -- Head # 1 Bottom straight jointer manual, remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12 -1/16"; With outboard bearing 4 3/4"; For tool circle 6 1/16"- 7-1/16" -- Head # 2 Right spindle Profile jointer automatic; For working height 4-3/4"; Remotely controllable with closed safety hood; Automatic stone adjustment -- Head # 3 Left spindle Profile jointer automatic; For working height 4-3/4"; Remotely controllable with closed safety hood; Automatic stone adjustment -- Head # 4 Top spindle straight jointer manual; remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12 1/16"; With outboard bearing 4-3/4"; For tool circle 6-1/16"- 7-1/16"Profile Jointer automatic; Remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 9-1/16" without outboard bearing 4-3/4" -- Head # 5 Bottom spindle straight jointer manual; remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 12-1/16"; With outboard bearing 4-3/4"; For tool circle 6 1/16"- 7-1/16"Profile Jointer automatic; Remotely controllable with closed safety hood; Automatic stone adjustment; Maximum jointing width 9-1/16" without outboard bearing 4-3/4" -- (4) Jointer cassettes for profile jointer, length 6" -- (2) Jointer cassettes for profile jointer, length 9" -- (1) Set of jointing stoneReadouts: -- Digiset (double mechanical readouts) for left and top radial adjustments. One readout is for the tool size and the other for the finished wood dimension (with Imperial inch adjustment -- Mechanical readouts on all other axes. Side pressure roller: -- (10) Driven feed roller shaft from above -- (5) Driven steel rollers in the machine table -- Axial setting range of the feed rollers opposite left spindle, 1-3/8" -- Extension of the feed shaft opposite the left spindle to 8 -1/4 in. -- Axial setting range of vertical spindle 3-1/8 in. Axial setting range of horizontal spindle 1 -3/4 in. (1st bottom 3/8 in.) -- All spindles diameter 1 -13/16" -- (6) Additional set of spacing collars, clamping length 6-11/16", diameter 1-13/16" -- Pressure shoe in front of 1st left spindle receding from tool, incl. lateral roller pressure, pneumatic -- Receding chip breaker in front of 1st top spindle, pneumatic. -- Pressure shoe in front of and guide after top spindle with mechanical digital displays

WEINIG PROFIMAT 23 Feed Through Moulder;(6)-Heads (B-R-L-T-T-B), working cap. 9-1/16" x 4-11/16".Specifications: -- Spindles 1-1/2" dia. with cutterhead speed of 6,000 RPM. -- Feed System & Features: variable feed speed from 20 - 78 FPM, powered by a 5.5 HP motor. -- Receding chip breaker at top spindles. Side pressure opposite right spindle; spring-loaded with (2) rollers; driven outfeed roller in bed. -- In-feed straightening table 2 M (78"), side pressure roller mounted to in-feed table. Note: Bare Machine: No dust manifold or tooling.

WENIG PROFIMAT 23E Feed Through Moulder5-Head (B-R-L-T-B), working cap. 9-1/16" x 4-11/16".Specifications: -- Spindle Sequence: Bottom 10 HP, Right & Left by 15 HP, Top 15 HP and Bottom 10 HP motor. -- Spindles: 1-1/2" diameter. with cutterhead speed of 6000 RPM. -- Digital Readouts: "DigiSet" digital readouts for chipbreaker and pressure element at top spindle -- FPM: Variable feed speed from 20 - 78 FPM, powered by a 5 HP motor -- Safety: Full enclosure sound proof booth -- Receding chipbreaker & pressure element at top spindle -- Rollers: Side pressure opposite right spindle, spring loaded with 2 rollers and driven outfeed roller in bed. -- Infeed straightening table 2 meter (6'6") -- Features central lubrication system via manual table lubrication pump. -- Machine is wired for 230 Voltage / 3 Phase Power using 146 Full Load Amps. -- Includes - All heads, rollers, and setup tools shown in photos are included.Overall Dimensions: 132";L x 78";W x 68";HApprox. 8,000LBS

Weinig Quattromat Q23V 4-Head Through Feed MoulderHead Configuration : (B-R-L-T) Profile or "S4S" Moulder,Specifications: -- 9-1/16" x 4-3/4" cap. -- Spindle sequence: Bottom 5.5 HP, right / left heads 7.5 HP , top 5.5 HP motor. -- Spindles 1-1/2" dia. at 6,000 RPM, mechanical digital readouts for setting accuracy. -- Feed speed of 26 FPM, 1 HP feed drive, direct drive.Equipped with & Features -- 6'- 6" Infeed straightening table with adjustable fence, table inserts for right and left heads. -- Sound insulated safety hood.Technical specifications: -- Machine dimensions 120" x 48" x 62", -- Electrical requirement (95 Amps) at 230 volts, 60cy. 3ph., -- Dust collection 4,500 CFM and Shipping weight 3,500 Lbs.

WEINIG PROFIMAT 22N Feed Through Moulder/Grinder Package Specifications: -- 5-Head (B-R-L-T-B), working width 8-5/8" x 4-3/4". -- Head sequence: Bottom 10 HP, right/ left 10 HP, top 15 HP, and bottom 10 HP motor. -- Spindle dia. of 1-1/2" with cutterhead speed of 6,000 RPM. -- Features: Mechanical digital readouts on all spindles; Digital readouts on left & top spindle. -- Feed speed variable from 18 - 78 FPM, 3 HP feed drive. (1) Powered table roller in machine bed at out feed. -- Complete with: Infeed straightening table 2 M (6'-6") and side pressure roller mounted to infeed table. -- Manual table lubrication pump, manuals sound & safety enclosure and dust collection manifold . -- Includes seventeen heads, extra feed wheels and neoprene feed wheels, as shown in Photos. -- Seller is also including the Owner's Manual.WEINIG RONDAMAT 934 Profile Grinder: -- 9" Arbor length, 11-1/2" max. tool dia., 1.5 HP motor, tilting head assembly for back relief grinding, clearance angle on peripheral of tools 10° - 30° and to each side 0° - 20°. -- Variable feed speed 1,800 - 3,000 rpm via a vari-speed gearbox, on-board wheel dressing, 9" max. wheel dia.; 0.16 HP coolant pump with built-in coolant tank. -- Includes: Operators manual, clamping nut, and pull-off bolt, 1-1/2" arbor, and an extra set of grinding wheels and toolingWEINIG OCMS measuring stand (not shown): -- With a working width of 300 mm. -- The allowable tool dimension of 3" to 11-3/4" head diameter. The measuring stand allows for electronic measuring and indicating of cutter head dimensions with electronic digital readouts; visually establishing the tool measurement, no setting errors, and no expensive CNC control. -- Magnifier screen viewer with 20:1 magnification; the cutterhead is placed in Powerlock tool post, all the operator does is view the scope and move the measuring carriage via precision dialing left to right. -- Measured values (radial) and (axial), tool dimensions both minimum and maximum are displayed. -- Includes: 1-1/2" arbor.These machines came out of a Mom and Pop shop and have been very well maintained. Both machines are in great working condition, and have no running issues.