BRANDT AMBITION 1870 (aka KDF 870) EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING); -- Specifications: Edge & Workpiece Capacity, 0.4 - 20 mm Edge thickness cap., incl. 3 mm PVC banding, min. workpiece width 65 mm (2.5") and min. length 160 mm (6.375"), panel thickness 8 - 60 mm (0.314" - 2.187".3 HP (2.2 KW) feed drive for variable feed speed 36 - 65 FPM (11 - 20 MPM), with CR engaged or applying solid wood up to 52 FPM (16 MPM) max feed speed.infeed panel support w/roller guide extends out to 1,000 mm (39").Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, motorized raise/lower upper pressure beam.Automatic chain track lubrication; top pressure section with non-marking neoprene pressure wheelsAll cutting & trimming workstations are HF (High Frequency Motors); Line control (no limit switches) for workstation functions. Equipped with: -- Pre-Milling Station: (2) 3 HP (2.2 kW) - 12,000 RPM "HOMAG" Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments. -- "Quick-Melt" Hot Melt glue system w/pre-melting hopper feed, "quick change" hopper & tank for color changes, reversible glue applicator roller rotation; approx. (12) Min heat-up time. -- Extended Magazine for application of solid edges from 0.4 - 20 mm (3/4") thickness and coil material from 0.4 - 3 mm thickness; Infrared heating unit positioned between glue roller and pressure zone to improved edge quality. -- Program controlled motorized pressure zone: Pressure section with (1) large driven and (4) pneumatically controlled idle rollers, SIKO digitals for setting. Reinforced guillotine for coiled edgebanding material 0.4 - 3.5 mm thickness and 8 - 55 mm height; -- Brandt "Power Control PC 20+" with 12' TFT flat screen monitor; front side USB port, 1 GB Flash Card, 600 MHZ Hard Drive, 256 MB RAM; Internal modem for remote diagnostic link.Edgebander Workstations: -- Front & Rear End Trim: (high speed version, 1 HP - 12,000 RPM ea.), pneumatic control for straight or chamfer-trimming. -- Servo controlled Top & Bottom Rough Trims: (2 HP - 12,000 RPM motor ea.) w/vertical & horizontal tracing, pneumatic (in/out position) control from control panel, tilts 0 - 25°. -- Top & Bottom Fine Trimmers: (1 HP - 12,000 RPM motor ea.), Servo control bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, Servo Control (in/out position) from control panel; contour profile trimming units (two 0.5 HP - 12,000 RPM motors), Servo Control (in/out position) from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). -- Corner Rounding Unit: (2) Motors (0.5 HP / 0.4 kW) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed. -- Quick Change Top & Bottom Profile Scraping Unit: With digital "quick-set" system for 2 - 6 mm radius (0.078" to 0.47"), Servo Control in/out from operator panel and pneumatically controlled blow-off nozzles. -- Top & Bottom Buffing u

0.4 - 3 mm (1/8") Edge thickness cap., automatic coil & strip feed magazine, guillotine for 3 mm PVC banding, fast startup (10 Min heat up) glue system. -- Workstations: Vertical travel double motor front & rear end trim, 0.25 HP - 12,000 RPM motors; top & bottom flush/bevel trimmers, bevel 0ø to 15ø, 0.35 HP - 12,000 RPM motors; top & bottom PVC scraping unit for up to 3 mm radius; top & bottom buffing unit, 0.15 HP - 2,750 RPM ea. motor; feed speed 30 FPM.

BRANDT "KD-68" EDGEBANDER1/4" (6 mm) Edge thickness cap. (will even do 8 mm max.), max. edgebanding height 60 mm (2-3/8"), workpiece length min. 160 mm and width 70 mm (2-3/4").Equipped with: -- Quick Melt glue system with 10 Min heat up time and reversible glue roller. -- Automatic magazine for strip & coil stock, 3 mm PVC guillotine, 3-roller pressure section.Workstations: -- Double motor end trim on uni-slide (0.33 HP - 14,400 RPM), chamfers 0° - 15° -- Top & bottom flush/bevel & radius trim, bevels 0° - 15° (0.5 HP - 14,400 RPM motor ea.), w/SIKO digital readouts. -- Top & bottom scraping for standard or 3 mm PVC edging, w/air jet blowoff and SIKO digital readouts. -- Top & bottom buffing (0.25 HP - 1,650 RPM), adjusts 0° - 40°. -- Feed chain feed speed 36 FPM.Complete with: Electronic motor brakes on both trimmers, padded sound enclosure, eye-level height swivel control panel w/fault sensor control, adjustable outboard panel support track, frequency converter & used tooling.

BRANDT KD77/2 C EDGEBANDER WITH CORNER ROUNDING0.4 - 12 mm (1/2") Edge cap; 8 - 55 mm Panel thickness; 160 mm (6-3/8") min. panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function; 14 MPM Feed Speed (11 MPM automatically when corner rounding)Equipped with: Quick heat-up glue system w/overhead hopper feed, "quick change" glue tank for maintenance & glue color change. -- Automatic magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections.Workstations: Double motor end trim (0.5 HP - 12,000 RPM motors), automatic chamfer from control panel 0° - 15°. -- Top & bottom flush/Fine trim (0.75 HP - 12,000 RPM motor) bevels 0° - 25°, with insert knives for 3 mm PVC radius; (4) position turret stop for electro-pneumatic axial movement of flush trimmer. -- 2-Motor Corner Rounding unit for leading and trailing edges of panels; either radius or chamfer cutters can be mounted; (0.5 HP - 12,000 RPM motors); 3 mm Max. edge thickness. -- Top & bottom scraping for 2 - 3 mm radius, -- Top & bottom buffing (0.125 HP - 1,400 RPM motors). -- End trim & flush trim stations have HF motors w/electronic brakes.Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, padded sound enclosure, extended, and used tooling.0.4 - 12 mm (1/2") Edge cap; 8 -55 mm Panel thickness; 160 mm (6-3/8") min panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function; 14 MPM Feed Speed (11 MPM automatically when corner rounding).

BRANDT KDF-520 EDGEBANDER (W/PRE-MILLING) -- Specifications:Edge thickness cap. 0.4 - 8 mm (5/16"). Panel thickness of 8 mm - 50 mm (5/16" - 2"). Min. panel length 160 mm (6-3/8") & 65 mm (2-1/2") min. width.Equipped with: -- Quick heat-up glue system (approx. 12 Min) w/quick change glue tank for maintenance & glue color change.Glue temperature indicator for both the glue pot & glue roller with LED thermostat, automatic temperature setback if the machine is idle for (15) Min or more.The glue applicator roller is reversible & retractable from the fence line. (1) drive plus (2) idle rollers "pneumatically controlled" pressure section. -- Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. WorkStations: -- (2) Motor Pre-milling Unit with: (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End trim (0.25 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system. -- Top & bottom glue scraping. -- Top & bottom buffing (0.25 HP - 2,800 motors). -- Trim Stations have HF motors w/electronic brakes. -- Operator & Machine Control:"POWER CONTROL PC 20+" Control. -- Complete with: Feed chain track speed 11 MPM (36 FPM), 3 HP feed drive. &#9679 Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. &#9679 Line control (NO limit switches) for workstation function. &#9679 Signal infeed light to insure proper spacing between panels. &#9679 Height adjustment with top pressure beam for all workstations. &#9679 Equipped with digital height indicator. &#9679 Safety hoods/doors. &#9679 Used tooling. -- Actual Model is BRANDT KDF 520

BRANDT - KDF 660, ...Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

BRANDT KDF 660 2C EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications:Work-Capacity 0.4 - 8 mm Edge cap; 8 - 55 mm Panel thickness; 160 mm (6-3/8") min. panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Feed-Speed 14 MPM (11 MPM automatically when corner rounding). Equipped With: -- Pre-Milling Station, for cleaning edges of panel. -- Quick Change Gluing System, for maintenance & glue color change. -- Automatic Magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" & Servo controlled pressure sections for quick edge thickness changeover. Workstations -- End Trimming: Double motor (2 x 0.5 HP - 12,000 RPM motors), automatic chamfer from control panel 0ø - 15ø. -- Pre-Flush Trimming: Top & bottom (2 x 0.5 kW approx. or 0.67 HP - 12,000 RPM motor) with (4) pre-set position index settings. -- Fine/Bevel/Radius Trimming Station: Top & Bottom (2 x 0.35 kW approx. or 0.50 HP - 12,000 RPM) bevels 0ø - 25ø, with combination flush/radius/chamfer cutter heads; horizontal & vertical tracing wheels, comes with optional brushless Servo motors for quick thickness changeover. -- Corner Rounding Station: (2 x 0.35 kW motors or 0.5 HP - 12,000 RPM motors) for leading & trailing edges of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Profile Scraping Unit: Top & bottom PVC radius scraping with pneumatic control, PVC Scrape collection box. -- Flat Glue Scraping Unit: Top & bottom glue-joint scrape station. -- Buffing Unit: Top & bottom (2 x 0.125 HP - 1,400 RPM motors).Complete With:&#9679 Operator Control Panel, Power Control PC 20+ with color LCD screen & soft keypad. &#9679 All trimming stations have HF motors w/electronic brakes. &#9679 Padded sound enclosure and used tooling. -- Options Include:220/480v, 3Ph, 60Hz transformer. -- Actual Model is BRANDT KDF 660 2C

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT KDN 330 COMPACT EDGEBANDERSpecifications: -- Edgebanding thickness 0.4 - 3 mm (0.02" - 0.12"), Max. edge banding height 45 mm (1.77"). -- Panel thickness 8 - 50 mm (0.31" - 1.97"), Min. panel width 60 mm (2.36"), Min. panel length 140 mm (5.51"). -- Feed chain height 35", Feed speed 11 MPM (36 FPM), Outboard support adjustment 13".Equipped with: -- 800 mm (31.50") Dia. Coil table. -- Hot melt granulate glue system, with 10 - 12 Min. Heat-up time, Reversible rotation glue applicator roller, & Automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min. to re-activate). -- 3 mm (0.12") PVC Pneumatic guillotine with Double-acting pneumatic cylinder, Automatic feed magazine, Roll & Fixed length. -- Pressure section, with (1) Large electronically-controlled & feed speed synchronized driven and (1) Small idler roll. -- 0.55 kW (3/4 HP) Feed belt motor, Touchpad control, with LCD Display, Sound enclosure.Workstations: -- Front & Rear End Trim Unit, with (2) 0.18 kW (1/4 HP) - 12,000 RPM - 200 Hz Motors with Electric brake, & 0° - 15° Chamfer. -- Top & Bottom Flush/Bevel Trim Unit, with (2) 0.27 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors with Electric brake, Combination insert knifes for flush & bevel trimming, Vertical & Horizontal tracing & 0° - 15° Chamfer. -- Top & Bottom Buffing Unit, with (2) 0.09 kW (0.12 HP) - 2,710 RPM Motors. -- Manual height adjustment of top pressure beam for all workstations, with Digital height gage.Complete with: -- Documentation.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Min or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. -- Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: -- PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Minutes or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. --Complete with:Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT KDN-530C Single-Sided Edgebander, with Corner RoundingNOTE: Seller purchased new in crate in 2010 & all workstations are adjusted by servo motors.Specifications: -- Edge thickness 0.4 - 6 mm (0.02" - 0.24"). -- Panel thickness 5/16" - 1-5/8", Min. panel length 160 mm (6.30"), Min. panel width 65 mm (2.56"). -- Feed speed 36 FPM.Equipped with: -- Line control (No limit switches) for workstation function. -- Automatic height adjustment, with Top pressure beam for all workstations & Digital height indicator for 8 mm - 40 mm (0.31" - 1.57") panel heights. -- "POWER CONTROL PC-20+" Control, with PLC (Programmable Logic Control), VGA Screen, Touchpad, & Internal modem for remote diagnostic link, Signal infeed light to insure proper spacing between panels. -- Quick heat-up glue system, Heat-up time approx. 12 Min., with Glue tank for maintenance & Glue color change, Glue temperature indicator for both glue pot & glue roller with LED thermostat, Automatic temperature setback if machine is idle for 15 Min., Glue applicator roller is reversible & retractable from fence line. -- Automatic magazine for strip & coil, 800mm Dia. (31.50") Coil table accommodates large coils of 3 mm (0.12") PVC stock, 3 mm (0.12") PVC Guillotine. -- (1) Drive plus (1) Split secondary roller pneumatically-controlled pressure sections. -- 3 HP Feed motor.Workstations: -- End trim unit, with 1/4 HP - 12,000 RPM High-frequency motors with Electronic brakes, Chamfers 0° - 15°. -- Top & bottom flush/radius trim unit, with 1/2 HP - 12,000 RPM High-frequency motors with Electronic brakes, Bevels 0° - 15°, with Insert knives for 3 mm (0.12") PVC radius & "Quickset" with Digital counters. -- Single-motor corner rounding unit, For "On-the-fly" corner rounding, with 1/2 HP - 12,000 RPM Motor. -- Top & bottom scraping unit, For 3 mm (0.12") Radius, with Pneumatically-controlled indexing system & Dust collection. -- Top & bottom buffing unit, with 1/4 HP - 2,800 RPM Motors.Complete with: -- Manual.NOTE: Seller estimates he has run 70,000 parts on machine.

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT F-13 Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL and veneer edgings, up to 3 mm max. thickness. -- Manually operated, 1/2" - 2-1/4" panel thickness, 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each); -- Built-in air jet blowoff device, 31" x 48" table size, and dual foot pedal controlNOTE: Intermittent fault in the control panel, which will require replacement.

BREWCO Model BBBH 6-Head Horizontal Resaw;Complete with the following Features & Specifications: -- Working dimensions: 6" Wide x 8" high capacity and length 21" to 72". -- Band: 13'-2" x 1-1/4" x 0.035 Blade provides thin kerf savings. Quick & easy blade height adjustments. -- Wheel diameter: 28" Dia., CNC machined, dynamically balanced, all steel. -- Belting: Rough top feed belt combines with opposing side feed rolls. -- Saw motors: 20 HP High Efficiency, 3-Phase electric motor on each head. -- Variable feed speed conveying: 5 HP Hydraulic drive from 20 to 120 FPM (6 to 36 MPM).

BREWER Single-head horizontal Re-saw;With the following features: -- 15 HP motor. -- 6-1/2" wide x 6-1/2" thick resaw cap. -- 2-belt drive, 36" working height from the floor. -- Variable speed hydraulic drive with top and bottom powered tire and belt, 30" dynamically balanced band wheels at 900 RPM for vibration free running. -- 1" or 1-1/4" wide bands.NOTE: No return conveyor system.

20" Width cap., 1/4" - 9" opening, 7.5 HP motor (3-phase) with 1.5 HP feed motor, both made in the USA, variable feed speed 20 - 32 FPM.Complete with: Segmented infeed roller, cast iron chipbreaker and adjustable bed feed rollers; 3-knife cutter with jack screw adjustment. - Includes (2) sets of knives.

BRIDGEWOOD BW-511MS Sliding Table Shaper Single Phase 4 HP Motor with forward & reverse.Specifications: -- 3/4″ Spindle with 4-1/2″ under the nut, and 3-1/2" of Spindle travel. -- (5) Spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. -- 52" Table Length, and 35 Sliding Table Length1-used BRIDGEWOOD BW-511MS SLIDING TABLE SHAPER. Table Length: 35″, Sliding Table Length: 52″, 3/4″ spindle with 4-1/2″ under the nut, Also , Spindle Travel: 3-1/2″, Motor: 4 HP, single phase, (5) spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. For operation on 220V, 1PHNote- the feeder in the photo is not included

BRYAN - CL 240-W-GI, ...Hot Water Tube BoilerThis Boiler was taken out of an Office Furniture Factory where it was used to heat drying tunnels to a temp of 120 F.Disconnected and in storage for 1-1/2 years.Details & Specifications:Model: CL240-W-GIInput MBH: 2,160/1,080Output MBH: 1,728BRYAN #: 971292Relief Valve Setting: 50 PSIGHeating Surface: 287 sq/ftMAWP Water: 60 PSIGNational Bond #: 41033Canadian Reg #: E6190.25Gas Data:Natural GasMax Input CFH: 2,160Min. Input CFH: 1,080Min. supply Pressure: 7 In. WCMax supply pressure: 14 In. WCManifold pressure in WC: 3.5Orifice size: DMS 29