BRANDT AMBITION 1650 FC HIGH FLEX EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): Specifications: -- Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units.Equipped with: -- 3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High-Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- QA 45 Quick-change glue tank with electronic switchable/emptying mode for easy maintenance & glue color change.Melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Adjustable glue amount with servomotorPressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") ma

BRANDT AMBITION 1650 FC High Flex EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Equipped with:3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- Quick-change glue tank for easy maintenance & glue color change, melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multistage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (2) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different radius profiles, pneumatic (2) position indexing for different edge thickness.

BRANDT AMBITION 1870 (aka KDF 870) EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING); -- Specifications: Edge & Workpiece Capacity, 0.4 - 20 mm Edge thickness cap., incl. 3 mm PVC banding, min. workpiece width 65 mm (2.5") and min. length 160 mm (6.375"), panel thickness 8 - 60 mm (0.314" - 2.187".3 HP (2.2 KW) feed drive for variable feed speed 36 - 65 FPM (11 - 20 MPM), with CR engaged or applying solid wood up to 52 FPM (16 MPM) max feed speed.infeed panel support w/roller guide extends out to 1,000 mm (39").Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, motorized raise/lower upper pressure beam.Automatic chain track lubrication; top pressure section with non-marking neoprene pressure wheelsAll cutting & trimming workstations are HF (High Frequency Motors); Line control (no limit switches) for workstation functions. Equipped with: -- Pre-Milling Station: (2) 3 HP (2.2 kW) - 12,000 RPM "HOMAG" Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments. -- "Quick-Melt" Hot Melt glue system w/pre-melting hopper feed, "quick change" hopper & tank for color changes, reversible glue applicator roller rotation; approx. (12) Min heat-up time. -- Extended Magazine for application of solid edges from 0.4 - 20 mm (3/4") thickness and coil material from 0.4 - 3 mm thickness; Infrared heating unit positioned between glue roller and pressure zone to improved edge quality. -- Program controlled motorized pressure zone: Pressure section with (1) large driven and (4) pneumatically controlled idle rollers, SIKO digitals for setting. Reinforced guillotine for coiled edgebanding material 0.4 - 3.5 mm thickness and 8 - 55 mm height; -- Brandt "Power Control PC 20+" with 12' TFT flat screen monitor; front side USB port, 1 GB Flash Card, 600 MHZ Hard Drive, 256 MB RAM; Internal modem for remote diagnostic link.Edgebander Workstations: -- Front & Rear End Trim: (high speed version, 1 HP - 12,000 RPM ea.), pneumatic control for straight or chamfer-trimming. -- Servo controlled Top & Bottom Rough Trims: (2 HP - 12,000 RPM motor ea.) w/vertical & horizontal tracing, pneumatic (in/out position) control from control panel, tilts 0 - 25°. -- Top & Bottom Fine Trimmers: (1 HP - 12,000 RPM motor ea.), Servo control bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, Servo Control (in/out position) from control panel; contour profile trimming units (two 0.5 HP - 12,000 RPM motors), Servo Control (in/out position) from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). -- Corner Rounding Unit: (2) Motors (0.5 HP / 0.4 kW) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed. -- Quick Change Top & Bottom Profile Scraping Unit: With digital "quick-set" system for 2 - 6 mm radius (0.078" to 0.47"), Servo Control in/out from operator panel and pneumatically controlled blow-off nozzles. -- Top & Bottom Buffing u

BRANDT KDF-550 C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDING Edge & Workpiece Capacity 0.4 -8 mm (0.016 - 0.31") edge; 8 -60 mm (0.31" - 2-3/8") panel thickness; 160 mm (6.29") min. panel length and70 mm (2-.75") min. panel width.Equipped with: -- Pre-Milling Station with diamond cutter heads, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. -- In-feed Fence, with servo motor positioning. -- Automatic Edge Magazine, for strip & coil stock, strips 0.4 mm-8 mm (0.016- 0.31"), coils up to3 mm PVC and "HD" guillotine. -- Pressure Section,1st. roller driven plus (3) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed, variable 8 - 14 MPM. (26 -46 FPM),11 MPM (36 FPM) when using contour trimming. -- BRANDT" PowerControl PC 16, Memory:256 MB Ram, 1 GB Flash Card Drive, Operator control panel w/22" color HD wide screen, soft keypad & internal modem for remote diagnostic link.Workstations: -- End Trimming, (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic chamfer from the control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/bottom (2) motors, 0.55 kW (3/4 HP) 12,000 RPM, auto tilt positioning 0° - 25°, with combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. -- Includes (3) positioning options, profile 1, profile 2, and flush trimming. -- Corner Rounding Unit (1) Motor 0.35 kW (1/2 HP) 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile(PVC) Top/bottom with (2) profiles. 1 mm and 2 mm or 3 mm instead of 2 mm, servo control positioning of vertical & horizontal copy wheels.PVC scrape collection box. -- Scraping Glue Unit: Flush top/bottom on the panel surface with floating insert knives. -- Buffing Unit: Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM.Complete with: Motorized, programmable hold-down pressure beam; padded sound enclosure -- Actual Model is BRANDT, OPTIMATKDF 550 C

BRANDT AMBITION 1440 FC (KDF-440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence: Radiant Heated with Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for Top & Bottom, Leading & Trailing edges & Corner Rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 FC (KDF 440 FC).

BRANDT KDF 110 (AMBITION 1110) Edgebander with Pre-Mill0.4 - 3 mm (1/8") Edge thickness cap., 8 - 40 mm (0.3" - 1.57") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- In-Feed Fence, adjustable, manual with digital indicator. -- Pre-Milling Unit, (2) motor, (1) jump, counter-rotating for the best possible glue joint. -- Gluing System, hot-melt, quick heat-up time and easy maintenance. -- Edge Magazine, automatic for strip & coil stock, 3 mm PVC guillotine, -- Side Pressure Section, (1) driven plus 2-idle roller w/digital readout setting.Workstations: -- End Trimming Unit, double motor end trim (2 x 0.5 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Multi Trimming Unit, top/bottom for flush/bevel/radius trimming with (3) quick setting positions. Motors (2 x 0.5 HP - 12,000 RPM) with insert knives. -- Buffing Unit, top/bottom (2 x 0.5 HP) motors. -- NOTE: Open station at end; scraping unit could be addedControls:LCD Display, approx. 2 x 6" with soft-keys for fast navigation and operator comfort. Complete With: -- Feed Speed, fixed 8 m/Min (26 FPM), 3 HP feed drive. Sound enclosure and Scraper collection box.Actual Model: AMBITION 1110

CAM-WOOD EB-L5PM EDGEBANDER (W/PRE-MILLING): -- Specifications:0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 50 mm (0.75" - 2") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 63.5 mm wide x 160 mm long (2.5" x 6.3"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Infeed Section: -- Pre-Mill Unit with: (2) 3 HP (2.25 kW) -12,000 RPM High Frequency motors. -- Feeding of edging by strip or coil is automatic and synchronous with panel feed. -- Gluing Unit: Roller driven by a 1 HP (0.75 KW) motor; Tank heating 2.3 kW. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled side pressure section with (3) pressure rollers; 1st synchronously driven, (2) idlers; Independent adjustment for straight edge banding.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. -- Cutting group moves on ways made of hardened steel, to guarantee high precision and reliability. -- Rough Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM Independent High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). -- Fine Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM -- Top & Bottom Scraper station with quick working or exclusion setting of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes. -- Top & Bottom Buffing/Polishing unit with (2) 0.25 HP (0.18 kW) - 1,400 RPM motors.Feed System & Features: -- 25 - 60 FPM feed speed powered by 2 HP (1.5 kW) gearmotor. -- Feed chain pads with precision ground round guides to ensure precise linear tracking of the workpiece. Replaceable rubberized surface inserts. -- Rubberized hold-down rollers with ball bearings for low friction and long life. -- Complete with: Sound / Safety covers for all work units with all required dust extraction outlets. Heavy, robust construction to eliminate vibration and ensures accuracy and stability.Includes: Outrigger support for wider workpieces. -- Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts. -- Total machine power is 11 kW. Transformers are available at an added cost to convert to desired alternate voltage requirement.

CAM-WOOD EB-K7PMX EDGEBANDER (W/PRE-MILLING): -- Specifications:0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 60 mm (0.75" - 2.36") panel thickness cap. -- Minimum panel dimensions 160 mm long x 88.9 mm wide (6.3" x 3.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Infeed Section: -- Pre-Mill Unit with: (2) 3 HP (2.25 kW) -12,000 RPM High Frequency motors. -- Feeding of edging by strip or coil is automatic and synchronous with panel feed. -- Gluing Unit: Roller driven by a 1 HP (0.75 KW) motor; Tank heating 2.3 kW. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled side pressure section with (3) pressure rollers; 1st synchronously driven, (2) idlers; Independent adjustment for straight edge banding.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. -- Cutting group moves on ways made of hardened steel, to guarantee high precision and reliability. -- Rough Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM Independent High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). -- Fine Top & Bottom Trim station with (2) 0.75 HP (0.56 kW) - 12,000 RPM. -- Top & Bottom Profile Scraper station with quick working or exclusion setting of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes. -- Top & Bottom Buffing/Polishing unit with (2) 0.25 HP (0.18 kW) - 1,400 RPM motors.Feed System & Features: -- 25 - 60 FPM feed speed powered by 2 HP (1.5 kW) gearmotor. -- Feed chain pads with precision ground round guides to ensure precise linear tracking of the workpiece. Replaceable rubberized surface inserts. -- Rubberized hold-down rollers with ball bearings for low friction and long life. -- Complete with: Sound / Safety covers for all work units with all required dust extraction outlets. Heavy, robust construction to eliminate vibration and ensures accuracy and stability.Includes: Outrigger support for wider workpieces. -- Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts. -- Total machine power is 11 kW. Transformers are available at additional cost to convert to desired alternate voltage requirement.

CAM-WOOD EB-L5 EDGEBANDER0.4 mm - 3 mm Edgebanding thickness capacity, 10 mm (3/8") - 50 mm (1.96") material thickness capacity, 63.5 mm (2.5") minimum part width, 160 mm (6.3") minimum part length. Equipped with: -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine. -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 4-liter capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Double Motor end trimming saw unit with (2) 1 HP (0.75 kW) - 12,000 RPM High-Frequency motors. Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel. -- Top & Bottom Trim station with: (2) 0.75 HP (0.56 kW) - 12,000 RPM High-Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). Includes (2) 3 mm radius cutters. -- Top & Bottom Buffing unit with (2) 0.50 HP (0.37 kW) - 1,400 RPM motors. Feed & Holddown: -- Feed rate of 12 MPM (40 FPM); feed chain pads with replaceable rubberized surface inserts. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Complete with: Sound enclosure protects the operator from noise and debris.

CANTEK - RapidEdge Pro, ...Edgebander w/Premill & Corner Rounding: -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Premill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counterrotating cutterheads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutterhead that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. --Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Premilling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface of

SCMI OLIMPIC K 800 T-FR2 EDGEBANDER EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge Capacity, 0.4 to 8 mm (0.016 to 5/16") for strip feeding. -- Panel Capacity, min. width 65 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 3.0 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit: Top/Bottom, 2 x 1.0 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12°. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Controls: -- Startouch Controller, 12" color touch screen, swivels 270° at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 36/52 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all trimming units. -- Electronic, programmable hold-down pressure beam positioning, lighted safety/sound enclosure cover and outboard panel support. -- Options Include: Dust Manifold as pictured. -- Actual Model: OLIMPIC K 800 T-FR2

SCMI K 208E SINGLE SIDED EDGEBANDER5/16" (8 mm) Max. edge cap., 1-3/4" max. banding height, 2-3/8" min. panel width and 6-/14" min. length. Equipped with: Automatic strip & coil feed magazine, Teflon coated glue pot (heat up time 10 Min), upgraded to Heavy Duty 3 mm PVC cap. guillotine, 3-roll pressure unit w/pneumatic controls. 42 FPM Fixed feed speed via 1 HP drive.Workstations: -- Double motor front & rear end trim (0.3 HP - 12,000 RPM motor ea.), tilts 0° - 15°, End trimmer mounted on 45° THK guides. -- Top & bottom trim station (0.8 HP - 12.000 RPM motor ea.), bevels 0° - 15°. -- Top & bottom PVC scraper for up to 5 mm radius; -- Top & bottom buffing unit (0.33 HP - 2,800 RPM motors). Complete with: Swivel control panel, pneumatic positioning of super finish, full cover sound enclosure, 200 Cy - 5 kW frequency converter & tooling.

SCM OLIMPIC K208ER EDGEBANDER WITH CORNER ROUNDING15/32" (12 mm) Max. edge cap., 2" max. (w/corner rounding only 1-3/4") banding height, 2-3/8" min. panel width and 6-5/16" min. length.Equipped with: -- Automatic strip & coil feed magazine w/Heavy Duty 3 mm PVC cap. guillotine. -- Teflon coated glue pot with glue roller application system complete w/automatic recycling device for unused glue. -- Digital thermostat adjustment for temperature control. -- 3-roll pressure unit w/pneumatic controls for all pressure rollers.Workstations: -- Double motor front & rear end trim (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15°, end trimmers mounted on 45° THK guide. -- Top & bottom fine/radius trimmer w/pneumatic positioning from control panel. -- Corner rounding units for leading & trailing edges. (2) 0.5 HP - 200 Cy Motors ea. -- Top & bottom PVC scraper for up to 5 mm radius. -- Top & bottom buffing unit (0.33 HP - 2,800 RPM motors). -- Hot air heating unit for PVC/ABS. -- Single 42 FPM fixed feed speed, 1 HP drive; heavy 3/4" drive chain with chain pads traveling on round & flat tracks.Complete with: -- Microprocessor for line control & glue temperature (can store up to 50 preset programs), swiveling control panel, pneumatic positioning of super finish, full cover sound enclosure, 200 Cy - 5 kW frequency inverter w/automatic motor brakes for all HF motors; includes used tooling. NOTE: Video of equipment was made in February 2021, prior to being decommissioned and placed in storage fully wrapped and ready for transport.

SCM OLIMPIC K 201 HFA Automatic Compact Edgebander, with 3 mm Max. Coiled Edgebanding Thickness & High Frequency MotorsSpecifications: -- Edgebanding thickness cap. (for both coil & strip) 0.4 - 3 mm (0.02" - 0.19"). -- Min. panel length for coiled edges (Min. width 200 mm) 140 mm (5.51"). -- Min. panel width for coiled edges 65 mm (2.56"). -- Panel thickness 8 - 40 mm (0.31" - 1.57"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Automatic adjustment of all units when panel thickness is changed. -- 20" Dia. Coil table. -- Automatic coil feed magazine, Manual strip feed. -- Teflon-coated glue pot. -- 1.2 mm (0.05") Cap. guillotine. -- Eye-level control, with GEFRAN "1000" LED Temperature controller. -- Adjustable feet.Workstations: -- Single-motor end trimming unit, with (1) 0.19 kW (1/4 HP) 12,000 RPM High-frequency motor & Copying device. -- Top & bottom flush trimming unit, with (2) 0.35 kW (1/2 HP) 12,000 RPM High-frequency motors and Front & Vertical copying devices.

SCMI OLIMPIC K 560 R EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge Capacity: 0.4 to 6 mm (0.016 to 1/4") for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); min. panel length: 140 mm (5-1/2").Min./max. Panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 600 mm (24").Equipped with: -- Pre-milling Station: (2) 2.0 HP (1.5 kW) motors; rectifies/cleans panels already sized. -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with: Quick change/disconnect Teflon glue pot for fast glue tanks change if needed; Heat up time approx. (10) Min. -- Pressure Section: Manual digital positioning; Teflon coated pneumatic driven roller & (2) spring loaded idle rollers.Workstations: -- End Trimming Station: (2) Front & rear 1/2 HP - 12,000 RPM motors mounted on THK guides; swivels 0° - 15° for straight & angle cutting. -- Top & Bottom Trimming Unit: (2) 0.7 HP - 12.000 RPM Motors; capable of tilting & pneumatic positioning for (3) settings, flush/bevel/radius trimming for quick setup. -- Corner Rounding Unit - "Round 2M" with: (2) 0.80 HP Independent motors that slide on THK guides. -- Top & Bottom Profile Scraping Unit with: Digital indicators; large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue scraping Unit: Eliminates any excess glue. -- Buffing Unit: (2)Top/bottom 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. -- Machine automation by PLC function and encoder positioned in the panel feed track pinion. -- Diagnostics for a quick solution to errors: Process statistics data (i.e., number of pieces/edges) and track feeding.Features & Complete with: -- 2-Speed feed speed of 40 & 60 FPM (12 & 18 MPM); (1) 2-1/2 HP feed drive motor. -- 200 Hz frequency inverter for all trimming units. -- Manual adjustable top hold-down pressure beam. -- Full sound enclosure cover and outboard panel support. -- Actual Model is: SCM OLIMPIC K 560 R

SNX - nVISION System2 G3, ...SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size: 2,400 x 2,400 mm (94" x 94"); max. material weight: up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Min. internal (inside) radius 80 mm (3.14"); min. external (outside) radius 30 mm (1'-18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness: 1 mm, min. = R 30 mm. &#9679 Edge thickness: 2 mm, min. = R 50 mm. &#9679 Edge thickness 3 mm, min. = R 80 mm. &#9679 Panel thickness 10 - 60 mm with edge thickness 1 mm. &#9679 Panel thickness 10 - 60 mm with edge thickness 2 mm. &#9679 Panel thickness 10 - 45 mm with edge thickness 3 mm.IMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece; automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: Laser for easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is still equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large interchangeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit. &#9679 Centralized control panel with individual controls for all stations to enable manual feeding of panels if desired. &#9679 Banding Station. &#9679 Edgebander Coil Stand. &#9679 Standard size vacuum pod for articulated arm. &#9679 80 mm (3") Dia. dust extraction outlet. &#9679 Foot pedal activation/deactivation control. &#9679 Larger feed roller. &#9679 QC Glue tank with sensor. -- Actual Model is: SNX nVISION System2 G3

SNX - nVISION System2 G3, ...SEMI-AUTOMATIC CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming. -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size: 2,400 x 2,400 mm (94" x 94"); maximum material weight: up to 104.5 kG (230 Lbs).Material thickness from: 10 - 60 mm (0.4" - 2.36"); banding thickness from: 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius: 80 mm (3.14"); minimum external (outside) radius: 30 mm (1'18"), based on 1 mm thick edge tape. &#9679 Edgebanding thickness: 1 mm, min = R 30 mm. &#9679 Edge thickness: 2 mm, min = R 50 mm. &#9679 Edge thickness: 3 mm, min = R 80 mm. &#9679 Panel thickness: 10 - 60 mm with edge thickness 1 mm &#9679 Panel thickness: 10 - 60 mm with edge thickness 2 mm &#9679 Panel thickness: 10 - 45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:Thermal regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece; automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: Laser for easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is still equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large inter-changeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit .&#9679 Centralized control panel with individual controls for all stations to enable manual feeding of panels if desired. &#9679 Banding station. &#9679 Edgebanding coil stand. &#9679 Standard size vacuum pod for articulated arm. &#9679 80 mm (3") Dia. dust extraction outlet. &#9679 Foot pedal activation/deactivation control. &#9679 Larger feed roller. &#9679 QC Glue tank with sensor. -- Options include:(1) Additional Telescoping Actuator arm & foot pedal

SNX - nVISION G2, ...Semiautomatic Contour Edgebander: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size of 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius of 80 mm (3.14"); minimum external (outside) radius of 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) NEW Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming & to maximize production throughput. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming. NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tan

SNX - nVISION System2 G3, ...Semi-Automatic Contour Edgebander -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") dia.Max. material size 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Min, internal (inside) radius 80 mm (3.14"); min. external (outside) radius 30 mm (1'-18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness: 1 mm, min = R 30 mm. &#9679 Edge thickness: 2 mm, min = R 50 mm. &#9679 Edge thickness: 3 mm, min = R 80 mm. &#9679 Panel thickness: 10 - 60 mm with edge thickness 1 mm. &#9679 Panel thickness: 10 - 60 mm with edge thickness 2 mm. &#9679 Panel thickness: 10 - 45 mm with edge thickness 3 mm.IMPORTANT: ALL minimum & maximum radii are affected by tape thickness quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:Thermal regulated glue pot heated via (2) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece; automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2-1/4"). -- Features: Laser for easy length identification with closed parts without the need for additional length measurement.The Laser detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large interchangeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized Control Panel with individual controls for all stations to enable manual feeding of panels, if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard size vacuum pod for articulated arm &#9679 80 mm Dia., (3") dust extraction outlet &#9679 Foot pedal activation/deactivation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor -- Actual Model is: SNX nVISION System2 G3

SNX Edgebanding heater and storage system. For straight-line and contour edgebanders which: - Keeps banding at the perfect temperature - Softens banding, making it more pliableSNX TECHNOLOGIES COIL HUB - Edgebanding heater and storage system. For straight-line and contour edgebanders which: - Keeps banding at the perfect temperature - Softens banding, making it more pliable - Increases adhesion - Decreases delamination issues - Allows a cleaner guillotine cut - It lessens the chance of chipping when trimming. This CoilHub also keeps the coils contamination-free, keeps the edgebanding easily accessible right at the machine, and can store up to 20 coils.