SCM K400 E --Specifications: -- Edge Capacity,0.4 to 6 mm (0.016to 1/4")for strip feeding. --Panel Capacity,min. width65 mmand 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-1/2"). --Equipped with: -- Automatic strip & coil feed magazine, Teflon coated glue pot (heat-up time 10 Min), -- 3 mm cap. guillotine, 3-roll pressure unit. -- Startouch control system with large 12" screen, graphic display with one touch, memory capacity up to 60 working programs. --Workstations: -- Double motor front & rear end trim "K-2" mounted on THK guides (0.4 HP - 12,000 RPM) , tilts 0° - 15°, rapid set up between straight and angled cutting with the automatic tilting device. -- Top & bottom flush & bevel trims "RI/800" (0.7 HP - 12.000 RPM), bevels 0° - 15° with precision digital indicators for quick setup. -- Top & bottom "RAS/V" scraping unit with container with filter for long chips; -- Top & bottom buffing unit (0.25 HP - 2,800 RPM ). -- 36 FPM Fixed feed speed, 0.75 HP feed drive.÷Complete with: --Full cover sound enclosure, mechanical digital readouts for setup adjustments, frequency inverter and outboard panel support. --Actual Model: "OLIMPIC K 400 E".

SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); Min. panel length: 140 mm (5-1/2").Min./max. panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 508 mm (20").Feed speed: 36 & 52 FPM (2.5 HP feed motor).Equipped with: -- Adjustable Infeed Fence:Manually preset with: Digital indicator, pneumatic in/out positioning; 1-coil feeder for banding up to 3mm thick with a 3 mm guillotine. -- Gluing Station:For EVA (Hot Melt) with quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. (8 - 10) Min. -- Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. - Includes "Strip Feed Magazine".Workstations: -- End Trimming Station: "K-SEL 2": Front & rear 0.5 HP - 12,000 RPM motor mounted on THK guides;, swivels 0° - 15°, rapid setup between straight and angled cutting with the automatic swivel cylinder. -- Top & Bottom Trimming Unit: 2 x 1.0 HP - 12,000 RPM Motors capable of tilting 0° to 25° degrees with copy wheels; pneumatic positioning for (3) settings: Flush/bevel/radius trimming via precision digital indicators; goes from 3 mm PVC to thin tape through the Controller for quick setup. -- 2-Motor Corner Rounding:(2) 0.80 HP Independent motors that slide on THK guides; features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations. -- Top & Bottom Profile Scraping Unit: "RAS/K" Profile scrape station for: 3 mm PVC, pneumatic positioning with digital indicators; large dia. copy wheels for max. accuracy, and pneumatic in/out positioning. -- Buffing Unit: Top/bottom; 2 x 1/4 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen displays; capable of storing (100) programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors; process statistics data, i.e., No. of pieces/edges and track feeding.Features & Complete with: -- (1) 2.0 HP Feed drive motor. -- 200 Hz Frequency inverter for all trimming unit.; -- Manual adjustable hold-down pressure beam -- Full sound enclosure cover and outboard panel support. -- Adjustable side support. -- Replaceable track pads. -- Digital inverter for electronic motor braking. -- Acoustical safety enclosure. -- Dust Collection: Working units are individually ported on the top of the safety enclosure for max. efficiency. -- Actual model is: SCM OLIMPIC K 600 T-ERL

SCMI OLIMPIC K 560 T-ER2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge Capacity: 0.4 to 6 mm (0.016 to 1/4") for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); min. panel length: 140 mm (5-1/2").Min./max. Panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 600 mm (24").Equipped with: -- Pre-milling Station: (2) 2.0 HP (1.5 kW) motors; rectifies/cleans panels already sized. -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with: Quick change/disconnect Teflon glue pot for fast glue tanks change if needed; Heat up time approx. (10) Min. -- Pressure Section: Manual digital positioning; Teflon coated pneumatic driven roller & (2) spring loaded idle rollers.Workstations: -- End Trimming Station: (2) Front & rear 1/2 HP - 12,000 RPM motors mounted on THK guides; swivels 0° - 15° for straight & angle cutting. -- Top & Bottom Trimming Unit: (2) 0.7 HP - 12.000 RPM Motors; capable of tilting & pneumatic positioning for (3) settings, flush/bevel/radius trimming for quick setup. -- Corner Rounding Unit - "Round 2M" with: (2) 0.80 HP Independent motors that slide on THK guides. -- Top & Bottom Profile Scraping Unit with: Digital indicators; large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue scraping Unit: Eliminates any excess glue. -- Buffing Unit: (2)Top/bottom 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. -- Machine automation by PLC function and encoder positioned in the panel feed track pinion. -- Diagnostics for a quick solution to errors: Process statistics data (i.e., number of pieces/edges) and track feeding.Features & Complete with: -- 2-Speed feed speed of 40 & 60 FPM (12 & 18 MPM); (1) 2-1/2 HP feed drive motor. -- 200 Hz frequency inverter for all trimming units. -- Manual adjustable top hold-down pressure beam. -- Full sound enclosure cover and outboard panel support. -- Actual Model is: SCM OLIMPIC K 560 T-ER2

SCMI MINI-MAX ME 25 EDGEBANDER, SINGLE SIDED SINGLE PHASE0.4 mm to 3 mm (1/8") Max. edge thickness cap. and 1.96" max. panel thickness; semi-automatic strip & coil feed magazine (feeds coil material automatically and strips one at the time); Teflon coated glue pot w/fast (8-10) Minute heat-up time, 1.2 mm cap. guillotine.Workstations: -- "ME 25" 2-Head -- Single motor end trim (0.8 HP - 12,000 RPM motor) -- Top & bottom flush trims (0.8 HP - 12,000 RPM ea. motor), straight or bevel cutters. -- Top & bottom scraping station. -- Top & bottom buffing, 3,000 RPM motors.22 FPM Fixed feed speed with 0.8 HP drive.Complete with: Sound enclosure, out rigger panel support, frequency converter, and used tooling on the stations.Features: Control Panel on machine infeed side Machine frame made of high rigidity ribbed steel to guarantee excellent support Top thick steel pressure beam with rubber coated wheels Manual adjustment of top beam with Auto positioning of operating units Numeric indicator of selected panel thickness Glue smoke-specific exhaust outlet; centralized extraction of the dust Panel support roller which can be extended the entire length of the machine

SCM OLIMPIC K 360TE COMPACT EDGEBANDER WITH PRE-MILLING .Specifications: -- Edge Capacity, 0.4 to 6 mm (0.016to 1/4") for strip feeding. -- Panel Capacity, min. width 65 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-1/2").Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator, pneumatic in/out positioning. -- Pre-Milling Station, RT-VP: Spindles 2 x 2.0 HP, 19,000 RPM, (1) with PLC controlled jump action and diamond cutter heads. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Manual digital positioning, (3) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station: Front & rear 2 x 0.25 HP, 12,000 RPM motors mounted on THK guides, swivels 0° - 15°, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Trimming Unit Flush/Bevel/Radius: Top/Bottom remote (via control panel) pneumatic positioning for (3) settings, flush/bevel/radius trimming, 2 x 0.7 HP - 12.000 RPM motors with precision digital indicators for quick setup. -- Profile Scraping Unit "RAS/V": Top/Bottom, manual pre-set up with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°. Controls: -- Orion 1 Plus Controller, fixed at in-feed of machine. with soft keys, graphics and 4" LCD display panel. It handles most machine set-up functions and workstations. Complete With & Features: -- Feed-speed, 36 FPM fixed, 1 x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units. -- Manual adjustable hold-down pressure beam, full sound enclosure cover and outboard panel support.Condition: ATFS

SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL/CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding.Panel Capacity: Min. Panel width 60 mm (2.375"); Min Panel length 140 mm (5.5").Min./max. Panel thickness 8 - 54 mm (0.375" - 2.125"); Minimum distance between panels 508 mm (20").Feed speed 36 and 52 FPM (2.5 HP feed motor) -- Equipped With:Adjustable In-feed Fence:Manually pre-set with digital indicator, pneumatic in/out positioning. 1-Coil feeder: For banding up to 3mm thick with a 3 mm guillotine.Gluing Station:For EVA (Hot Melt) with Quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. 8-10 Min.Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. Includes "Strip Feed Magazine" -- Workstations:End Trimming Station: "K-SEL 2" Front & rear 0.5 HP, 12,000 RPM motor mounted on THK guides, swivels 0° - 15°, rapid set up between straight and angled cutting with the automatic swivel cylinder. Top & Bottom Trimming Unit: 2 x 1.0 HP - 12.000 RPM Motors capable of tilting 0 to 25 degrees with copy wheels. Pneumatic positioning for (3) settings, flush/bevel/radius trimming via precision digital indicators to go from 3 mm PVC to thin tape through the controller for quick setup.Two Motor Corner Rounding:(2) 0.80 HP independent motors that slide on THK guides. The features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations Top & Bottom Profile Scraping Unit: "RAS/K" profile scrape station for 3 mm PVC with pneumatic positioning, with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: "STARTOUCH" Controller with 12" touchscreen display, capable of storing 100 programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors. Process statistics data, ie. No. of pieces/edges, and track feeding. -- Features & Complete With:1 x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units;Manual adjustable hold-down pressure beam;Full sound enclosure cover and outboard panel support.Adjustable side support. Replaceable track pads. Digital inverter for electronic motor braking Acoustical safety enclosure.Dust Collection: Working units are individually ported on the top of the safety enclosure for maximum efficiency.Suitable Transformer for 230V to 600V, 3 Ph. Actual model is SCM OLIMPIC K 600 T-ERL.

BRANDT KD77/2 C EDGEBANDER WITH CORNER ROUNDING0.4 - 12 mm (1/2") Edge cap; 8 - 55 mm Panel thickness; 160 mm (6-3/8") min. panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function; 14 MPM Feed Speed (11 MPM automatically when corner rounding)Equipped with: Quick heat-up glue system w/overhead hopper feed, "quick change" glue tank for maintenance & glue color change. -- Automatic magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections.Workstations: Double motor end trim (0.5 HP - 12,000 RPM motors), automatic chamfer from control panel 0° - 15°. -- Top & bottom flush/Fine trim (0.75 HP - 12,000 RPM motor) bevels 0° - 25°, with insert knives for 3 mm PVC radius; (4) position turret stop for electro-pneumatic axial movement of flush trimmer. -- 2-Motor Corner Rounding unit for leading and trailing edges of panels; either radius or chamfer cutters can be mounted; (0.5 HP - 12,000 RPM motors); 3 mm Max. edge thickness. -- Top & bottom scraping for 2 - 3 mm radius, -- Top & bottom buffing (0.125 HP - 1,400 RPM motors). -- End trim & flush trim stations have HF motors w/electronic brakes.Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, padded sound enclosure, extended, and used tooling.0.4 - 12 mm (1/2") Edge cap; 8 -55 mm Panel thickness; 160 mm (6-3/8") min panel length and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function; 14 MPM Feed Speed (11 MPM automatically when corner rounding).

BRANDT "KD-68" EDGEBANDER1/4" (6 mm) Edge thickness cap. (will even do 8 mm max.), max. edgebanding height 60 mm (2-3/8"), workpiece length min. 160 mm and width 70 mm (2-3/4").Equipped with: -- Quick Melt glue system with 10 Min heat up time and reversible glue roller. -- Automatic magazine for strip & coil stock, 3 mm PVC guillotine, 3-roller pressure section.Workstations: -- Double motor end trim on uni-slide (0.33 HP - 14,400 RPM), chamfers 0° - 15° -- Top & bottom flush/bevel & radius trim, bevels 0° - 15° (0.5 HP - 14,400 RPM motor ea.), w/SIKO digital readouts. -- Top & bottom scraping for standard or 3 mm PVC edging, w/air jet blowoff and SIKO digital readouts. -- Top & bottom buffing (0.25 HP - 1,650 RPM), adjusts 0° - 40°. -- Feed chain feed speed 36 FPM.Complete with: Electronic motor brakes on both trimmers, padded sound enclosure, eye-level height swivel control panel w/fault sensor control, adjustable outboard panel support track, frequency converter & used tooling.

BRANDT - KDF 660, ...Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT KD 56 EDGEBANDER0.4 - 3 mm (1/8") Edge thickness cap., automatic coil & strip feed magazine, guillotine for 3 mm PVC banding, fast startup (10 Min heat up) glue system. -- Workstations: Vertical travel double motor front & rear end trim, 0.25 HP - 12,000 RPM motors; top & bottom flush/bevel trimmers, bevel 0ø to 15ø, 0.35 HP - 12,000 RPM motors; top & bottom PVC scraping unit for up to 3 mm radius; top & bottom buffing unit, 0.15 HP - 2,750 RPM ea. motor; feed speed 30 FPM.

BRANDT F-13 Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL and veneer edgings, up to 3 mm max. thickness. -- Manually operated, 1/2" - 2-1/4" panel thickness, 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each); -- Built-in air jet blowoff device, 31" x 48" table size, and dual foot pedal controlNOTE: Intermittent fault in the control panel, which will require replacement.

BRANDT KDN-530C Single-Sided Edgebander, with Corner RoundingNOTE: Seller purchased new in crate in 2010 & all workstations are adjusted by servo motors.Specifications: -- Edge thickness 0.4 - 6 mm (0.02" - 0.24"). -- Panel thickness 5/16" - 1-5/8", Min. panel length 160 mm (6.30"), Min. panel width 65 mm (2.56"). -- Feed speed 36 FPM.Equipped with: -- Line control (No limit switches) for workstation function. -- Automatic height adjustment, with Top pressure beam for all workstations & Digital height indicator for 8 mm - 40 mm (0.31" - 1.57") panel heights. -- "POWER CONTROL PC-20+" Control, with PLC (Programmable Logic Control), VGA Screen, Touchpad, & Internal modem for remote diagnostic link, Signal infeed light to insure proper spacing between panels. -- Quick heat-up glue system, Heat-up time approx. 12 Min., with Glue tank for maintenance & Glue color change, Glue temperature indicator for both glue pot & glue roller with LED thermostat, Automatic temperature setback if machine is idle for 15 Min., Glue applicator roller is reversible & retractable from fence line. -- Automatic magazine for strip & coil, 800mm Dia. (31.50") Coil table accommodates large coils of 3 mm (0.12") PVC stock, 3 mm (0.12") PVC Guillotine. -- (1) Drive plus (1) Split secondary roller pneumatically-controlled pressure sections. -- 3 HP Feed motor.Workstations: -- End trim unit, with 1/4 HP - 12,000 RPM High-frequency motors with Electronic brakes, Chamfers 0° - 15°. -- Top & bottom flush/radius trim unit, with 1/2 HP - 12,000 RPM High-frequency motors with Electronic brakes, Bevels 0° - 15°, with Insert knives for 3 mm (0.12") PVC radius & "Quickset" with Digital counters. -- Single-motor corner rounding unit, For "On-the-fly" corner rounding, with 1/2 HP - 12,000 RPM Motor. -- Top & bottom scraping unit, For 3 mm (0.12") Radius, with Pneumatically-controlled indexing system & Dust collection. -- Top & bottom buffing unit, with 1/4 HP - 2,800 RPM Motors.Complete with: -- Manual.NOTE: Seller estimates he has run 70,000 parts on machine.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: -- PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Minutes or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. --Complete with:Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT KDN 330 COMPACT EDGEBANDERSpecifications: -- Edgebanding thickness 0.4 - 3 mm (0.02" - 0.12"), Max. edge banding height 45 mm (1.77"). -- Panel thickness 8 - 50 mm (0.31" - 1.97"), Min. panel width 60 mm (2.36"), Min. panel length 140 mm (5.51"). -- Feed chain height 35", Feed speed 11 MPM (36 FPM), Outboard support adjustment 13".Equipped with: -- 800 mm (31.50") Dia. Coil table. -- Hot melt granulate glue system, with 10 - 12 Min. Heat-up time, Reversible rotation glue applicator roller, & Automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min. to re-activate). -- 3 mm (0.12") PVC Pneumatic guillotine with Double-acting pneumatic cylinder, Automatic feed magazine, Roll & Fixed length. -- Pressure section, with (1) Large electronically-controlled & feed speed synchronized driven and (1) Small idler roll. -- 0.55 kW (3/4 HP) Feed belt motor, Touchpad control, with LCD Display, Sound enclosure.Workstations: -- Front & Rear End Trim Unit, with (2) 0.18 kW (1/4 HP) - 12,000 RPM - 200 Hz Motors with Electric brake, & 0° - 15° Chamfer. -- Top & Bottom Flush/Bevel Trim Unit, with (2) 0.27 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors with Electric brake, Combination insert knifes for flush & bevel trimming, Vertical & Horizontal tracing & 0° - 15° Chamfer. -- Top & Bottom Buffing Unit, with (2) 0.09 kW (0.12 HP) - 2,710 RPM Motors. -- Manual height adjustment of top pressure beam for all workstations, with Digital height gage.Complete with: -- Documentation.

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Min or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. -- Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT AMBITION 1120 FC (aka KDF 120 C) (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with: -- Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: -- End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out. -- Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1120 FC (aka KDF 120 C)