PTR - PT-330, ...Self-Contained CompactorSpecifications: -- Charge Box cap.: 1.5 Cu/yard -- Container cap.: 30 Cu/yard -- Clear Top opening: (L x W) 41” x 60” -- Feed height: 40" -- Hydraulic cylinders: (2); Bore 4” -- Hydraulic cylinder rod: 2-1/2” -- Horsepower: 10 -- Cycle time: 31 Sec -- Total normal force: 42,708 LbsEquipped with: -- Standard 3-button controls -- On/Off key switch -- Mushroom stop

PTR - 2507-HD, ...2-1/2 Yard Stationary CompactorSpecifications: -- Charge box capacity: 2.5 Cu/Yd -- Clear top opening (L x W): 54-1/2" x 60" -- Total normal force: 59,376 Lbs -- Cylinder bore: 6" -- Cylinder rod: 3-1/2" -- Capacity per hour: 63 Cy/Hr -- Average cycle time: 57 SecEquipped with: -- Heavy-Duty structural steel components -- 3-Button controls

CANTEK C-14RS Straight Line Rip Saw; Absolute straight line feeding Rip Saw. Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Excellent precision work accuracy and durability.Specifications: -- 4.92" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 20 HP arbor motor; swings 12" thru 16" dia. blade at 4,500 RPM; with 24" distance from blade to saw column. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Feed System & Chain: -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows). -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. When oil runs out the machine track stops running to avoid damage to track. Features: -- Precision Built Saw Arbor constructed of nickel chrome steel, large diameter, accurately ground and dynamically balanced. The arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V-Belt driven from below, with easy to access adjustments and controls. -- (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- Soft start - Star Delta starter. Telemecanique U/L magnetic starters.Options available at additional cost: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03)..................................... $ 495.00 -- Extra Saw Blade: 14”x0.157” kerf x 1.5” bore x 60T (CANC14RS-BLADE-14)........... $ 118.00

CANTEK SRS330 Straight Line Rip Saw;Features: -- Very Rigid machine body with a welded steel frame with an integral cast & machined table, which is fitted with a sturdy cast column & saw unit. -- Excellent precision work accuracy and durability. -- Absolute straight line feeding up to 13 ft. of ripping. -- Precision caterpillar chain and double "VEE" extra long (47.2”) guide rails are made of special cast iron the chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Holddown rolls (6 rows).Specifications: -- Max. work piece thickness 4.33". -- Min.work piece length 8". -- Distance between saw and column 18.1". -- Saw arbor dia. 1" and Saw blade dia. 10” - 14". -- Saw arbor speed 4,300 RPM. -- Useable Chain Length 47”. -- Glue line guarantee 13’ (+/- 0.0098” or 0.25 mm). -- Feed speeds variable 30 to 130 FPM. -- Arbor motor 20 HP -- Feed motor 2 HP -- Table size 36.6" x 64.6, Table height 31-7/8". Utilities: -- 230 V = 60.8 Full Load Amps. -- Electrics 460/3/60 = 30.4 Full Load Amps. -- Dust Collection Outlet 4” -- Net weight 3,190 Lbs.Available Options: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03) -- Extra Saw Blade: 14”x0.157” kerf x 1.5” bore x 60T (CANC14RS-BLADE-14)

CANTEK R-18 Heavy Duty Straight Line Rip Saw "Cuts From The Bottom"Equipped with & Features: -- Extra Heavy Main Frame Throughout with large support table. -- 6” Minimum length with this type of saw the blade is cutting downwards, forcing the Blade onto the chain – hence max. stability and safety are realized. -- Better chip clearance for shavings on deep cutting. -- Glue Joint Range – 12” to 10 Ft.Specifications: -- Depth of Cut 4.7” (120 mm) max. -- Split chain – double track with HRC60 Rockwell Hardened Guideways. -- 26” (660 mm) Saw to Column. -- (8) Press Rolls hold material firmly on the track. -- 20 HP Main Motor. -- 3 HP Feed Motor. -- Feed Speed 42 to 164 FPM variable. -- Automatic chain and track Oiler -- 41” Length of chain above table -- Saw Arbor Height adjustable -- Max. 18” Blade Diameter x 2” Bore Dia. saw Arbor with 14 mm pin at 6 5mm centers.Complete with: -- Saw Arbor Brake Included -- Anti-kickback fingers top and bottom -- Dust collection outlets: Top 4" (100 mm), Bottom 6” -(150 mmm). CFM Required: 1,400 CFM. -- Table Dimensions: 78-3/4” x 40” x 33.5” high (Can be added to optional) -- Net weight - 4400 Lbs. -- Stock Machine Electrics 460/3/60 to UL/CSA Standards (Other voltages available on request)Note: The advantage of cutting from below on thick material, the gullet of the sawblade projects above the stock to clear the shavings halfway through the cut

CANTEK - C 12 RSH, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK C10RSStraight Line Rip SawSpecifications -- 12" Over cutting Rip Saw ruggedly constructed with cast iron & ground tables, -- Cast iron pressure housing with (6) guide rollers and solid welded steel base chassis -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", -- Feedspeeds of 50, 65 and 85 FPM - 4,500 RPM, --10 HPsaw arbor motor; 1 HP feed motor, --Min. workpiece length 8", max. cutting thickness 3-3/8", --13 3/4" distance between saw and column, -- 30" X 50" table size, 31-1/2" table height.Equipped with & Features: -- Cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- (1)-piece cast iron chain with a diamond cut surface for positive material feeding.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2". Features: -- The cast iron upper-pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding.Approx. (600) Hours production time.Total amperage is 21.5 amp and the gross weight is approx. 2,530 Lbs.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. --:1-Piece cast iron chain with a diamond cut surface for positive material feeding.Total amperage is 21.5 and the gross weight approx. 2,530 Lbs.

CANTEK C-12RSH Overcutting Straight Line Rip Saw;Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (8) holddown rollers and solid welded steel base chassis.Specifications: -- 3.35" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 15 HP arbor motor; swings 8" thru 12" dia. blade at 4,500 RPM; with 18" distance from blade to saw column. -- Arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V Belt driven from below. -- 31-7/8" From floor to top of table; table is 39" wide x 57" long. -- Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Feed & Chain: -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding and absolute straight line feeding. -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. -- Equipped with high-frequency hardened chain Guide Rails. -- The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows).Features: -- Easy to access adjustments and controls. -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. -- Equipped with: (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- (1) 5" dia. dust outlet. -- Soft start, Star Delta starter - Telemechanique-Square D, Magnetic Wye/Delta Starters - Low Amperage Soft-Starter on the arbor motor - Electrics to UL/CSA Standards.Available Options when order with machine: --20mW Laser (FPIMLC1320W) & Laser Holder (FPICAN03) – made in N.A.... $ 495.00 -- KANEFUSA 12" Glue Joint Carbide Rip Saw Blade...$ 165.00

CANTEK HB-800 32" Vertical Band Resaw32" Wheel diameter, 20 HP motor Vertical Band Saw;Specifications: -- 3.543" (90 mm) wheel width, 30-5/8" throat capacity, 15-3/8" under guide capacity. -- 4" Blade width X 216- 217-1/8" blade length. -- 20 HP main motor, generates a blade speed of 5,024 SFPM.Features: -- Heavy fabricated steel machine frame. -- Specially designed Bakelite guide blocks provide rigid side blade support for straight cutting. -- Large cast iron work table is precision ground & can tilt to a maximum of 45°. -- Convenient blade tension adjustment by means of a handwheel and gauge. -- Cast iron upper and lower saw wheels are precision machined and dynamically balanced. -- Rack & pinion blade guide adjustment. -- Wheel is crowned for proper blade tracking & added stability of the blade.Complete with: -- Foot brake for braking wheels & blade. -- Blade lubrication system and reservoir for lubricant keeps blades cool.Including Electrics to UL/CSA - all starters -- Auto Start-Delta control for main motor with Emergency Stop Switch -- Telemecanique brand magnetic switchHF-150A Feeder: -- 1 HP motor with variable feed speed from 16 - 66 FPM; 6" feed opening. -- Pneumatic tensioned feed roller. -- Feed pressure is adjustable. -- Feed roller opening & closing is controlled by a foot switch for operator convenience. -- Knurled steel roller.

CANTEK - C14RS, ...Straight Line Rip SawSpecifications: -- Overcutting Rip Saw. -- 4.92" Max. thickness cap; 8" min. length. -- Variable feed speeds from 49 to 128 FPM; powered by a 2 HP feed motor. -- 1-1/2" Dia. saw arbor powered by 15 HP arbor. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Equipped with & Features: --(3) Rows of antikickback fingers: (2) top & (1) bottom, for safe operation. -- (8) Holddown rolls for increased control and precise straight line cutting (6 rows). -- 6" (150 mm) Wide chain track runs on double-V guide rails, which are made of special cast iron for added wear. -- Magnetic Controls.NOTE: Comes with 208 Volt transformer and (2) carbide blades.

CANTEK - C14RS, ...Straight Line Rip SawSpecifications: --Overcutting Rip Saw. -- 4.92" Max. thickness cap; 8" min. length. -- Variable feed speeds from 49 to 128 FPM and powered by a 2 HP feed motor. -- 1-1/2" Dia. saw arbor powered by 15 HP arbor motor. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long. Equipped with & Features: -- (3) Rows of antikickback fingers: (2) Top & (1) Bottom, for safe operation. -- (8) Holddown rolls for increased control and precise straight line cutting (6 rows). -- 6" (150 mm) Wide chain track runs on double-V guide rails, which are made of special cast iron for added wear. -- Magnetic Controls.

CANTEK MODEL MRS-175 6.9” THICK CUTTING HEAVY-DUTY GANG RIPSAW: -- FEATURES: -- Massive cast iron base provides incredible absorption characteristics for high quality deep cutting operations -- Precision chain and rails (dip chain) system facilitates straight line cutting -- Equipped with a blade mist cooling device providing cooling and cleaning for sawblades during cutting increasing blade life and improved cut quality. -- Motorized saw arbor and thickness adjustment for operator convenience. -- Specially designed auxiliary powered outfeed roller assures maximum smoothness of workpiece outfeed especially when working on extra thick, heavy and moist wood. -- A digitally controller lubrication unit is provided to provide consistent oil protection to the feed chain and guide rails. If the oil level drops below a safe level a warning lamp will light up and the feed chain will stop automatically. -- Equipped with an electronic amperage display which is tied in to an overload protection where if the saw motor exceeds a rated amperage the feed chain slows down automatically. This prevents the potential damaged to the saw arbor and/or blades and also prolongs blade life up to 20%. -- Variable feed speed adjustment by frequency inverter from the front of the machine. -- Please note. with safety cover non-CE -- Measurement: 255x210x170(cm)N.W./G.W.:3,150KGS/3,350KGS -- SPECIFICATIONS -- Max. cutting thickness, 6.9” -- Max. cutting width, 13-3/4” -- Fixed inside blade to column, 14.9” -- Min. working length, 27-1/2” -- Max. saw blade diameter, 14” to 18” -- Sawblade bore, 70 mm or 90mm – double keyed -- Saw arbor diameter, 70 mm without sleeve - 90mm with sleeve -- Saw arbor speed, 2500 RPM -- Saw arbor motor, 75 HP (100 HP optional) -- Saw arbor elevation motor, 1/2 HP -- Feed motor, 3 HP (5HP optional) -- Variable feed speed, 8 – 80 FPM (higher speed optional) -- Powered raise & lower of rolls, 1/2 HP -- Dust hood dia., 8” -- Table height (pass line), 29.3” -- Electrics – to UL/CSA standards 230/460 or 575-volt, 3-phase, 60-cycle -- Table area (L x W), 72.4” x 31.1” -- Overall dimensions (L x W x H), 95.5” x 90.5” x 63”, Net weight 6,600 lbs.

CANTEK MRS 300 Multi Blade (Gang) Rip Saw: General Description: -- Frame is Cast Iron, all the main parts are enclosed, ensuring protection and perfect stability. -- Straight line caterpillar style feeding with heavy guided chain. Chain blocks are special cast iron with heat treated & precision ground pins. -- Nickel chrome steel Saw Arbor with 70 mm OD – dble. keyed quick removal sleeve.Features & Includes: -- (3) Sets of Anti-Kickback Fingers (2) top, (1) bottom. -- Powered Rise & Fall to the pressure rollers. -- New style round Fence Bar support with quick shift long fence. -- Automatic Centralized lubrication system. -- Automatic Star-Delta Starter (slow speed start) and low voltage controls. -- C.E style European guard & safety features. -- Long fence for control of long material. -- Electrics to 230/460 or 575 Volts, 3-Phase, 60 Cycles.Specifications: -- Max. Working Thickness, 4 5/8” (120 mm) with 15” Blade diameter. -- Min. Length, 20” standard or 12" with short stock attachment. -- Saw Sleeve Usable Length(between outside saws), 12" (305 mm). -- Sawblade Dia., 200 to 350 mm (8” to 14”). -- Saw arbor Sleeve OD (Diameter), 70 mm; Saw arbor diameter, 50 mm. -- Saw arbor vertical adjustment, 3.6” (90 mm).Equipped with: -- 50 HP Saw Motor – Saw Arbor Speed 3,800 RPM. -- Powered Pressure Rollers (Rise/Fall), 1/2 HP motor. -- Feed Speeds 25 - 100 FPM (8 - 39 MPM); Feed Motor with 2 HP drive. -- (2) 6” Dia. Dust Hood. -- Table Size, 30” x 60"; Table Height from floor 33.5".Other Information: -- Net Weight, 4,510 Lbs, Shipping Weight, 5,060 Lbs - Machine Dimensions, 82.68” 59” x 56.5", Shipping dimensions, 71” x 67” x 63”. -- Included: (1) Removable saw sleeve, (1) Set of (38) spacers; NOTE: Saw blades not included.OPTIONAL EXTRAS - AVAILABLE:Short Stock & Thin material cutting attachment12"-300mm min. length & 3.75" - 95mm max. thickness (can be added and/or used at any time) (Required for high accuracy cutting) (CANMRS300A-SHT-STK)....................................................................................................................................... $ 620.00 20mW Laser (FP MLC1320W) & Laser Holder w/6” Bolt on Base-Stand(FP MBN03-XF8000)............................................................................................................ $ 1,020.00 OPTIONAL EXTRAS – AVAILABLE (Cont’d):NEW – Single Blade Mechanical Quick Lock Collars that can be used on the 70mm sleeve for individual blade quick setting and locking process (no spacers required) – This is desirable especially if you have to quick change from size to size and you don’t have the spacers to run a special size of product (Each CANMRS300-AM36-045-0).................................................................................................. $ 210.00 Extra for spare saw sleeve (CANMRS300A-SLEEVE)................

CANTEK - MRS-340-M2, ...Rip Saw Multiblade with CAMERON SkewSpecifications -- 4.3" Max. thickness with 14" dia. fixed blade(s); 3.3" with 12" fixed blade(s); 4" with 14" movable blades and 2.95" with 12" movable blades; 13.4" max. working width between outside saws 25.6: max. -- 0verall width; 5-1/2" max. distance to fence from inside fixed blade; 0.59" to 13.38" max. saw travel; 23-1/2" min. stock length; 19.7" possible with optional short stock holddown (reduces thickness capacity). -- With 70 mm dia. x 13-3/4" long saw arbor powered by a 50 HP motor driving the blades at 3,800 RPM; 3 HP feed motor; provides feed speeds from 15 to 135 FPM; -- 0.5 HP Lift motor for holddown roll. -- Infinitely variable saw shifting speeds from 0.78" to 3.15" per second. -- 72" x 31" table size; sits 30" from the floor.Equipped with & Features -- Cast iron main frame with main parts enclosed to ensure protection and perfect stability. -- HD Precision straight line caterpillar-type feed chain with easily replaceable bolt-in cast steel or Urethane chain ads (optional). -- Fully programmable position sets (10) programs of (10) sets each or infinitely variable foot pedal position set; user-friendly -- Touchscreen control (free-standing operators control console) is integrated with 32-bit microprocessor and (2) RS232 ports for incredible positioning speeds and EXACT blade positioning. -- Touchscreen with full and easy programming capabilities and joystick control; saw blade positioning is accomplished by industrial series Servo Motor and control. -- Blade speed is infinitely adjustable from 0.78" to 3.54"/Sec to match all operations; blade positioning can be initiated by electronic joystick control (efficient & quick) or the touchscreen controls. -- (2) Saws independently or (2) saws per shifter (optional as a cluster) or with a single or bank of saws with spacers can be set up on the inside of the saw arbor to Gang Rip, if desired. New short sock-cutting device included. -- Top pressure roll system is electronically positioned from the front control panel for lumber thickness. -- Position readout; top roll holddown system is mated to the Servo positioning short stock shoe to provide optimum straight line ripping and safety; top rolls are spring tensioned and tension is adjustable (pneumatic). -- Specially designed and Patent Pending Precision Glide Lock with nickel chrome steel saw arbor with super technology for easy maintenance and free saw shifting; (2) shifting saw bushings are equipped with specially designed rollers for most accurate and very fast saw positioning. -- (3) Rows of antikickback fingers. -- Variable feeding speeds from 16' to 135' FPM inverter motor and speed control with LED readout. -- Electronic overload sensing system is integrated into the inverter feed system providing automatic speed reduction under heavy amperage load. -- (2) Powered top & bottom outfeed rolls are included; powered roll system facilitates positive flow

CANTEK MRS-340M-1 GANG RIPSAW WITH (1) SHIFTING BLADE and the following specifications and features: Capacities are: -- 4.3" Max. thickness with 14" dia. fixed blade(s); 3.3" with 12" fixed blade(s); 4" with 14" moveable blades and 2.95" with 12" moveable blades; 13.4" max. working width between outside saws. 25.6" max. overall width; -- 5.5" Max. distance to fence from inside fixed blade; 0.59" to 13.38" max. saw travel; 23-1/2" min. stock length; 19.7" possible with optional short stock holddodwn (reduces thickness capacity. -- With 70 mm dia. x 13-3/4" long saw arbor powered by a 50 HP motor driving the blades at 3,800 RPM; 3 HP feed motor provides feed speeds from 15 to 135 FPM;1/2 HP lift motor for hold-down roll; infinitely variable saw shifting speeds from 0.78" to 3.15" per second; (2) 15 mW laser lights; (2) 12" or 14" dia. x 90 mm bore blades; 72" x 31" table size sits 30" from the floor. Features include: -- Cast iron main frame with main parts enclosed to ensure protection and perfect stability; HD precision straight line caterpillar type feed chain with easily replaceable bolt-in cast steel or Urethane chain ads (optional); -- Fully programmable position sets (10) programs of (10) sets each or infinitely variable foot pedal position set; user friendly Touch Screen control (free standing operators control console) is integrated with 32 bit micro processor and (2) RS232 ports for incredible positioning speeds and EXACT blade positioning. -- Touch Screen with full and easy programming capabilities and joystick control; saw blade positioning is accomplished by industrial series Servo Motor and control; blade speed is infinitely adjustable from 0.78" to 3.54" IPS to match all operations; blade positioning can be initiated by electronic joystick control (efficient & quick) or the touch screen controls. Equipped to shift (1) saw independently or (2) saws per shifter (optional as a cluster) or with a single or bank of saws with spacers can be set up on the inside of the saw arbor to gang rip if desired. New short stock cutting device included -- Top pressure roll system is electronically positioned from the front control panel for lumber thickness; includes position readout; top roll hold down system is mated to the servo positioning short stock shoe to provide optimum straight line ripping and safety; top rolls are spring tensioned and tension is adjustable (pneumatic pressure is optional). -- Specially designed and Patent Pending Precision Glide Lock with nickel chrome steel saw arbor with super technology for easy maintenance and free saw shifting; (2) shifting saw bushings are equipped with specially designed rollers for most accurate and very fast saw positioning. -- (3) Rows of anti-kickback fingers; variable feeding speeds from 16 to 135 FPM inverter motor and speed control with LED readout; electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage lo

CANTEK MODEL MRS-610M-4 GANG RIPSAW WITH (4) SHIFTING BLADES: Specifications: -- (4) Shifting Blades and 4.2" Max. cutting thickness without pressure plate, 3.7" with pressure plate; 24" Max. cutting width; 35.4" Max. material width of pass-through; 60 HP Saw motor (larger optional); 2.8" (70 mm) Saw arbor diameter turning at 3800 RPM; 12" Min. or 14" max. Sawblade diameter; 2.8" (70mm) Sawblade bore when mounted directly on shaft, 3.5" (90 mm) when mounted on saw sleeve; 5 HP feed motor with variable feed speeds from 25 to 200 FPM; 1/2 HP pressure roller raising motor; 24" Min. stock length; 31.9" Min. stock length with board under (2) rollers.Features and Benefits: -- The main frame is cast iron, all the main parts are enclosed, ensuring protection and perfect stability -- Nickel chrome steel saw arbor with 70 mm OD double keyed quick removal sleeve. -- Heavy duty precision straight line feeding caterpillar chain type. -- Feed chain with easily replaceable bolt in cast steel or urethane pads - optional. -- The top pressure roller system is electronically positioned from the front control panel with regards to lumber thickness with position readout. -- Top roller hold down system is mated to the servo positioning short stock shoe providing optimum straight line ripping performance and comprehensive safety. -- Pneumatic pressure (infinitely variable) to the holddown feed rollers provides better control of the lumber. -- Nickel chrome steel saw arbor. -- Variable feed speeds of 16 - 200 FPM. (5 - 60 m/min) via an inverter motor and speed control with led readout. -- Electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage load. -- New - short stock cutting device included. -- Digitally controlled lubricator for chain. -- Centralized lubrication system. -- (2) Powered top & bottom outfeed rollers are a standard feature. The powered roll system facilitates positive flow of the stock through the gang saw and onto outfeed conveyors or transfers. -- (3) Rows of anti-kickback fingers. -- Telemechanique - automatic star-delta starter (low amperage soft-start) and low voltage controls -- Controls are mounted on the saw for easy convenient machine operation. -- Includes 12' infeed table -- Gang saw sleeve is optional extra -- Electrics to 230/460 or 575-volt, 3-phase, 60-cycle to UL/CSA standards -- Complete Shifting Fence Infeed Tables and complete Outfeed Sweep Systems, handling decks and Stacking Systems are available.Options available: -- Add for 75 Hp Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter. -- 100 HP Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter -- 125 HP Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter. -- Short Stock Feeding device (min. length 12" - must use 12 blades for max. thickness of cut of 2.16" (55 mm). -- 20mW Laser (FP MLC1320W) & Laser Holder w/12" Bolt on B

CAROLINA BLOWER Size 80-6 Material Handling Fan with Motor. --Specification: -- Can handle approx 35,000 CFM @ 11" SP and 840 RPM. -- Comes with: Westinghouse Life-Line (high efficiency) 125 HP, 405T frame, ODP Motor complete with pulleys.. -- Motor is not mounted on base. -- Actual Model is 80-6SD.

CAROLINA BLOWER 45-6 Standard Duty Fan/Motor package assembled complete 30 HP motor. -- Rated at 8,860 CFM at 10" SP. Fan inlet diameter is 19". -- Fabricated with 3/8" thick wheel blades, 1/4" thick housing, primed and painted beige. 30 HP TEFC motor . Unitary base, V-belt drives, shaft and belt safety guards. -- This is an Industrial Material Handling fan with paddle-wheel construction. Also available in Heavy Duty version at extra cost, with thicker scroll-housing to handle airborne smaller solid wood or similar material.