2019 Peterson 2710D Grinder -4550 hours -C18 CAT Engine764 HP -Motor replaced at 3500 Hours by CAT with Papers -Clean machine ready to work

Peterson 4800 Flail Debarker Wireless remote controlled Reman engine Runs and operates good

2005 Peterson 5410 Grinder -5800 hours -CAT 3412 Engine 1000H.P -Needs a discharge belt -New feed chains -New tip protectors

2019 Peterson 5000H Chipper -9500 frame hours -Complete Cat rebuild done at 6800 hours -4 flail -Loader -Tons of service receipts and very clean machine Videos upon request

1999 Peterson Pacific 5000G Chipper -1000 h.p. 3412e engine -8000 hrs since major overhaul -3 flail -Spare flail pump -Load adapters replaced within last 1000 hours -Fan pump replaced 1500 hrs ago,Also has had swing and boom pump replaced -New Ecm has less than 750 hrs -New muffler -New feed roll teeth -New heater and a/c -Spare clutch, Spare belts, Spare pins and Seal kits -Babbit or key knife system -Fleet maintained

2002 Peterson 7400a Horizontal Grinder -End of summer 2022 we installed NEW -Cylinder packs and bearings -Both turbos -High pressure oil pump -Ecm -Injectors -All gaskets and orings -Oil pump -Twin disk clutch -Had the heads completely rebuilt -Radiator completely gone through -Rebuilt feed floor -Rebuilt mill -Mill bearings checked for clearance and passed -All belts and chains in good shape -Alot of extra screens and parts come with it. Some are brand new

2024 Peterson 6310 Chipper -227 hours -Platinum warranty -16 pocket drum -Micro chips 1/2 inch or smaller -New machine goes for over 1.5 million -Going different route PRICE REDUCED!!!!!!

Log trailer -Bushings worn -lights work -225 tires on it -Single point suspension -102" wide

Pitts Pup Trailer Used for 6 months Good rubber Adjustable bunks Like new

2003 Ponsse Bison 6 Wheel Forwarder Runs Approx 14K Hrs

2000 Ponssee Cobra HS10 Harvester Cat 3116 125 crane Eberspacher Preheater 700/45-22.5 Tires New batteries Work ready

2022 Ponsse Bear Processor -2300+ hrs(working) -H8 head -Tires 95% -Tracks 95% -Tight and dry

2007 Ponsse Beaver Processor -18000 hours -H6 head operates good same with computer -Tracks and chains -Tires @70% -Tight and dry machine

2011 Ponsse Ergo Processor/Harvester H7 head 2 owner 13k hours Complete refurb by Ponsse Currently on the job in use daily 2014 Ponsse Wisent forwarder also available

2016 Ponsse Ergo 8 wheel Processor -12,900 hours -C44+ crane -H8 head -New head pump -New drive coupler -Pump gear box rebuilt -New windows -New exhaust -New feed wheel arms -New feed wheels -New knives -Saw motor and complete saw assembly and much more -All work done by Ponsse Ready to work

2008 Ponsse Buffalo Fowarder -17,400 hours -New boom chains -Re- sealed crane pump -Tracks are new -Recently repainted machine -Owner operated and on a job working

2014 Ponsse Wisent Forwarder 9500 hours 2 owner Nice machine Currently on the job in use daily 2011 Ponsse Ergo processor with H7 head also available

2003 Ponsse Wisent Fowarder -23547 hours -Replaced -Turbo -Steering cylinder -Water pump -New batteries -Rear right tire on the back is brand new -Tracks are like new -Hydraulic lines were replaced on it recently -Heat and ac work good

2000 Ponsse Bison -Uknown hours -Perkins 6 cylinder diesel -New iQan control system for the crane and steering (100% joystick controls) -New Webasto preheater -Tracks and tire chains included -New Red Dot heat and AC system -Brand new LED lights -Good glass on sides and rear, front isn’t bad but not new -Has a few small leaks but otherwise ready to go to work

2023 Ponsse Ergo 8wd -26 hours on machine -Tracks come with machine 2 sets are new -H8 head Available as a package deal also for the fowarder in pictures(700 hr)