Late model Gabbiani G2 Panel Saw that is ready to be moved immediately!

25 Spindles 10 Dowel inserters 2 Dowel hoppers Glue tank Water tank Left and right adjustable fences 4 Pneumatic clamps foot pedal controlControl Panel

Gannomat Pro-Line 50 • Row of holes as well as line drilling in the SYSTEM 32 mm • 50 (2 x 25) holes in one drilling cycle

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Laminating Rolls: 61" (155 cm) roll face with thermally conductive high release silicone surface; upper and lower main rolls internally heated; temperature controlled by state-of-the-art infrared sensors and digital PID controllers Laminating Opening: 1.5" (3.8 cm) maximum opening controlled with dual air cylinders. Laminating Material Uses heat activated and pressure-sensitive materials 0 - 55" (0 - 140 cm) wide on a 3" (7.6 cm) ID core Laminating Speeds 0 to 14.5 fmp (0 to 4.5 mpm) Post Lamination: Fanless cooling system provides uniform, filtered air for thermal shock without exposure to dangerous fan blades. Vinyl Transfer Complete roll to roll transfer, lamination, and edge trimming in one pass Safety Features • Two emitter-receiver photoelectric systems protect rolls from damage. • Emergency kick cables front and rear. • All electrical and moving mechanical parts are located in bolted cabinets • Four emergency stop buttons Installation Requirement 220 to 240 VAC, 50/60 Hz, 55A. 32 A per phase. Air: 2 cfm at 100 psi, minimum(0.5 m3 at 700 vPa)

GBN Explorer Pallet Nailer

Generac 200 HP Genset

Giben K305 Edgebander Manufacturer specs (to be confirmed): Standard Configuration Panel Thickness: 10~60mm Edge Thickness: 0.4~3mm Motor Power: 2.35Kw Maximum Curve Radius: 20mm Cutter Maximum Range: 50mm Working Pressure: 0.6 MPa Outline Dimension: 960 x 950 x 1000mm Gross Weight: 280Kg Voltage: 220-480V

General Motors Power Takeoff Unit Detriot Diesel #5136548

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

Go Fast Single Head Resaw

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

Gorbel 500 Lbs Ceiling Hoist

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Weight18.57 tStandard tyres385/65R22.5 LRBucket capacity0.54 m³Mobile/CrawlerMTransport length8.4 mTransport width2.6 mTransport height3.6 mModel seriesVEngine manuf.VolvoEngine typeTAD572 VEEngine power160.3 kWDimension lxwxh982x854x992 mmDisplacement5.1 lRevolutions at max torque2300 rpmMax. torque910 NmNo. of cylinders4Cylinder bore x stroke110x135 mmEmission levelTier 4f

8 foot bar 11HP electric motor 489 volt 3 phase

Griggio C250 Rip Saw 250 mm Wide belt (10")

6' x 14' capacity 4 HP motor 220 volt 3 phase stop system on base