Heil 10.5' x 32' Triple Pass Drum Dryer 1. Jackson Harvester Burner 24 million BTU 2. Fuel Bin 3. Pipe and fan from fuel bin to burner 4. Air lock on dryer 5. 8 X 24 3 pass dryer 6. Trunnions 7. Fans to dryer 8. Pipe to cyclone 9. Cyclone 10. Pipe to fuel bin 11. Fan moving sawdust to fuel bin 12 Hog with 200 HP motor 13 Dust collection system

HewSaw SL250 Trio sawing line from 2005 This line has already been dismantled and loaded into containers. It is ready to ship! - Consists of log positioning devices, conveyors and three sawing machines. HewSaw sawing line is designed to process logs ranging from 100 mm – 420 mm small end diameter, to 550 mm large end diameter, with length 2.4 - 6.2 m - Feeding speed of the sawing line can be adjusted from 50 m/min to 150 m/min. Top diameter: 100–420 mm Maximum log diameter: 550 mm Cant height in Chipper Canter: 75–410 mm Cant width in Chipper Canter: 75–410 mm Cant height in Rip Saw: 63–310 mm Cant width in Rip Saw: 75–410 mm Saw kerf: 4.2–5.0 mm Chip length: 20–30 mm Sawline 1. Measuring conveyor 2. Log scanner 3. Log positioner 4. Chipper canter 5. Cant scanning conveyor 6. Cant scanner 7. Cant saw 8. Seperating conveyor EK2 9. Cross conveyor 10. Belt conveyor 11. Cant turner 12. Infeed conveyor 13. Rip saw 14. Belt conveyor 15. Belt conveyors under machines, for waste handling 16. All electric boxes

High Tech 20' Trim Saw (10) Blades

High Point 12" Resaw with Return Conveyor

Hildebrand

This mill is ready to be removed from the current location. - 4 Roll Cases 24’’ 2 center 6.5 Diameter 45’ 56’ 62’ 70’HMC All motor controls included - 7 Lumber Decks Flat Chains 10’ 12’ 16’ 20’ 24’ 40’ 82’ 5 Chains WIDC All motor controls included - 2 Log Decks - 28’ Long 12’wide 3 chains stop loader - 14’ long 12’ wide 4 chains stop loader - All motor controls included - Newman Trimmer, drop saws, scrap belt chain 100’x 24’ - Unscrambler 16’wide x 5’high 8 chains - Air Compressor Model SSREP100 HP - Air Dryer storage tank - HMC Model mm10 4 heah block carriage 49’ - HMC Saw Booth - HMC Feed Works - HMC Husk 54’ bottom saw 36’ top saw - 200 HP motor - HMC Log Turner - HMC Drop Belt Live Off Barrer - 10 Headrig saws inserted tooth 54” - Roof Top Chain 10ft 5 Chain - Blower system - Tie-Cant Deck 62’Lx13’ W 4 chain all motors & Controls - Roof Top Lumber Deck 30’L x 13’W 5 chains all motors & Controls

HMC Model HD-40 Carriage Drive 50 HP Hydraulic Unit

HMC Carriage 5x10 Cab with controls System is already removed from service and ready to load. Notes from seller: Carriage is 17'1" longKnee spacing is 63" from 1 to 2 78" from 2 to 3 1 to 3 is 141 1/4" Carriage frame is 76 1/2 " wide Track centers are 62" Track rails are worn out. We used the old track frame for our new carriage

HMC AC-40 Carriage Good Condition

Three systems available. Pricing will include removal and loading onto trucks. - Hurst Hybrid 600 HP 150 PSI - Hurst Hybrid 200 HP 150 PSI - Hurst Hybrid 300 HP 150 PSI Each system should include (email for specifics): Hurst Hybrid Vessel Hurst Boild Furnace with cast grates Hurst underfeed stoker system Hurt Metering conveyor system Overfire air combustion fan Underfire air combustion fan Hurst combustion air preheater Access platforms with ladders Boiler system control panel (PLC, frequency drives, UDC, control for automatic operation)

Used 1995 Hurst Hybrid Boiler system 200 HP 150 PSI 1– Hurst Hybrid Boiler 200 HP 150 PSI Boiler 1 - Hurst Boiler 200 HP Woodfired Furnace for Boiler vessel with cast iron grate system. 1 – Deaerator Tank 1 – Blowdown Separator for fuel storage equipment 1 – 8” Underfeed stoker System 1 – 10” Metering Bin Screw Conveyor with Hopper 1- 20HP Over fire air combustion fan 1- 15HP Under fire air combustion fan 1- Hurst multi-cyclone collectors 1- Induced draft fan

Hurst Boiler System 1. 1- Used1995 200HP 150 PSI Hurst Hybrid Vessel 2. 1- Used 1995n refractory lined boiler furnace 3. 1- 8” underfeed stoker system 4. 1- 10” Fuel feed metering conveyor system 5. 1- Overfire air combustion fan with ductwork 6. 1- Underfire air combustion fan with ductwork 7. 1- Multi cyclone flyash collector 8. 1- Induced draft fan with exhaust stack 9. Muti cyclone and ID fan support steel with legs 10. Access platforms to boiler with ladders 11. Hurst open vented feedwater tank with 2 Grundfos feedwater pumps and control panel 12. Blowdown separator 13. Hurst Boiler control panel 14. Boiler piping parts 15. Boiler electrical parts 16.Equipment loaded onto trucks Optional: Fuel handling and storage supply system: Walking floor Vibrating Screen Screw conveyor Controls

600 hp 300 psi Hurst Hybrid boiler system. 1996 year model Equipment Included: 1- 1- Hurst 1996 Hybrid Boiler 2- 1- Hurst woodfire furnace box 3- 1- Hurst 12” metering conveyor system 4- 1- Overfire air combustion fan 5- 1- Underfire air combustion fan 6- 1- Hurst combustion air preheater 7- 2- Hurst multi-cyclone collectors with rotary air lock 8- 1- Flyash Duct 9- 1- Induced draft fan with exhaust stack 10- Access platforms with ladders 11- Boiler and collector system support frame and legs 12- Boiler system control panel (PLC Controller, frequency drives, UDC) 13- Under feed fuel stoker system with cast iron grate system. 14- 20,000 lbs/hr DA Tank with two 15 HP Grunfos Pumps 15- Rear Injection Fan

Trim Saw: 6-Head System includes: Unscrambler, Infeed Deck, Auto Loader, Control Panel with Color HMI

Hutto Shaving Mill Hydraulic cylinder to hold dow scrap material Infeed shoot: 16" x 30" 30 HP Motor

Box Opening 16" x 30" 20' Conveyor Included Custom Trailer Base

Hutto Shaving Mill 9' Box (2) Heads 50 HP Motors Outfeed conveyor

iDry Standard Dry Kiln - (2) Available 2,000 BF Capacity

iDry Plus Dry Kiln Excellent Condition Electric

2 Cutter Wheels on One Spindle Fully Enclosed Easy Changeover for Different Saw Guides 120V