Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Precision 58" Chip Pac 6-Knives 72" Cyclone H-Type blower with dual load out chutes 6'x6' Screen 25' Vibrating Infeed with transition chute to chipper with fiberglass section and MDI metal detector

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

Precision 10'x20 Screen 3-Decks: 3/4” top deck, 1/4” middle deck screen

Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on

Precision 55 screener, was working when pulled out of production.

10x10 Chip Screen 2-Layer screens

System includes: - Infeed System: Volumetric Feed Hopper, adjustable front gate, flow regulator, 43' Infeed Conveyor Belt System, flow regulator and transition chute. - Bagging System: Feeder with scraper, stand alone Volumetric hopper, manual feed system, chute for small bags, additional chute for bulk bags (supported by forklift), rolling system to fill either small or bulk bags, hot air sealer system (14"-28" wide bags) - Palletizing System: In-line turner conveyor, horizontal bag flattener, 8' gravity roller conveyor - System is set up for 575 V service

Premier Tech Form, Fill & Seal Bagger: Model FFS-200 Robotic Palletizing system model AP-425 Dismantled and ready to ship!

SPECIFICATIONS: - Chip Capacity: 50 LBS/HR - Puck Size: 2? - Chamber Size: 16? X 6? - Puck Exit Conveyor: 6' X 6? - Approximate Floor Space: 5’8? LR X 4' FB X 6’2? H - Electrics: 480 Volt, 3 Ph, 60 Cyc Allen Bradley Panelview 300 Controller

Excellent condition Less than 6 hrs on machine

Rethceif HC2020 Bagging Line Robot stacking system Available approx Spring 2024 Automatic FFS system, ( Sealer, Perimeter Guard, Film Unwind, and Form Tuber) Electric infeed augers 100 HP Hydraulic Motor with Dual Pumps Tower Plunger Gate. Pre Weigh Feed Gate 30’ Long x 16” Diameter Incline Auger.

Rotex 6' x 16' Chip Shaving Screen

Rotex HICAP 2100 Chip Screen

Rotochopper MC256 3126B 300 Hp CAT Engine Dust Control 60 Teeth Roto902 8 row rotor 3/4 x 2 1/4 bolts 3 button remote-Elec Sol Model EL24VRT Drive Belt BL10/5V1600 Square D buttons on 3 button box 24 Volt System Radiator PreCleaner CAT radiator CAT Alternator 9X7803 Turbo II 68-6 intake S/N 87384 DT motors w/case drain Hyd Screen changer Hyd Valve Ass'y Hyd Actuator Hyd powerfeed shock kit Magnet Long Conveyor Pintle Hitch 3 15/16" FAG main rotor bearings Smooth underrotor belt R2 lacing 3/8" steel infeed belt 2 7/16" bearings and shaft on infeed Slab ramp w/blocks No flip down sides on infeed AW68 hyd oil Gruber Welding fuel & oil tank BEE70 omega coupler 3/4" baffled screen Will need to be moved on a trailer.

RUF Briquette Press More info coming!

Salsco 60" Electric Shaving Mill Includes:Chip sizer/breaker

Salsco 60 " Shaving Mill Diesel engine Stationary Mill Seller believes it is a 2009 or 2010. There is 10 knives ( 5 rows with 2 knives each)