You Have Selected
 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
321 Results Found for Pallet Viewing 1 - 25 of 321 results
$2,650
AIRTEK AR 500 Refrigerated Air Dryer. -- Approx. 500 SCFM at a max. of 300 PSI, 38° pressure dew point; uses "R-22" Refrigerant, exchanger, centrifugal condensate separator; powder-coated finish. -- Equipped with: Gauges for discharge pressure, refrigeration liquid temp., refrigeration suction temp., ambient temp., inlet compressed air temp., outlet compressed air pressure, differential air pressure, inlet compressed air pressure, and outlet compressed air temp. -- Complete with: 2" NPT Pipe connections, 1/4" electronic drain valve.
Equipment Location:WEST COAST
$60,970
AMERICAN PAC 4029-730 HORIZONTAL BALER -- Auto-tie Model -- 30 HP motor -- 7" Cylinder -- System pressure 3,000 psi -- Feed opening 40" x 29" -- Bale size 30" x 43" x variable -- Dust system included -- Shredder and feeding conveyor not available -- Loaded on your truck
Equipment Location:WEST COAST
$152,800
AMERICAN BALER 6042W-10T30 HORIZONTAL AUTO-TIE -- (2) 30 HP motor -- Bale size 43" x 43" Variable -- 10" Main cylinder -- Feed Opening 60" x 42" -- Shear; Replaceable Serrated Bolt On -- Auto Tier; 5 wire, can use 12,11 or 10 gauge black annealed baling wire -- Ram cycle 13.5 sec. -- Ram cycles per min; 4.4 -- Weight 28,150 lbs.
Equipment Location:ATLANTIC CDN
$67,990
AMERICAN BALER 13567F AUTO-TIE HORIZONTAL BALER -- 10" Main cylinder -- 75 HP motor. -- Feed opening 44" x 28" -- New chamber floor and bottom of ram -- Upgraded wire feed system -- All hydraulics/electrical inspected, repaired/replaced as needed -- Reconditioned and Guaranteed good working order£
Equipment Location:MIDWEST
$58,900
AMERICAN BALER PAC5029-750R AUTO-TIE HORIZONTAL BALER. -- 50 HP motor -- 7” Cylinder -- 115,450 Lbs compressing force -- 98 psi Ram force pressure -- 3,000 psi system pressure -- Large feed opening 50” x 27.5” -- Up to 10.2 TPH production rate -- Finish bale 30” x 42” x variable length -- Loaded on your truck
Equipment Location:MIDWEST
CDN$8,795
ATLAS COPCO GA-55 Rotary Screw Air Compressor. -- Equipped with: 75 HP - 1,755 RPM Motor, totally self-contained, single stage rotary screw air end, 267 CFM at 125 PSI rated operating pressure, max. modulate pressure 135 PSI. -- Complete with: Inlet air filtration, oil injected lubrication, motor starting control system, air cooled after-cooler, moisture separator, and drain trap. -- Includes: "ELEKTRONIKON" Operator display panel with: Pressure gauges, control mode selection, remote & automatic start, and hour meter. -- (52,253) Total operating hours.
Equipment Location:EASTERN CDN
$8,750
ATLAS COPCO "GA-55" Air Compressor (Rotary Screw) -- 75 HP - 1,755 RPM Motor, totally self-contained, single stage rotary screw air end, 340 CFM @ 125 PSI rated operating pressure, max. modulate pressure 125 PSI. -- Standard features include: Inlet air filtration, oil injected lubrication, motor starting control system, air cooled after-cooler, moisture separator, and drain trap. -- Operator display panel with: Pressure gauges, control mode selection, remote & automatic start, and hour meter
Equipment Location:EASTERN CDN
$8,500
ATLAS COPCO GA-55 Rotary Screw Air Compressor. -- Equipped with: 75 HP - 1,755 RPM Motor, totally self-contained, single stage rotary screw air end, 267 CFM at 125 PSI rated operating pressure, max. modulate pressure 135 PSI. -- Complete with: Inlet air filtration, oil injected lubrication, motor starting control system, air cooled after-cooler, moisture separator, and drain trap. -- Includes: "ELEKTRONIKON" Operator display panel with: Pressure gauges, control mode selection, remote & automatic start, and hour meter. -- Air-end rebuilt and control upgraded. (53,299) Loaded operating hours.
Equipment Location:MIDWEST
$32,900
BAKER C 4-HEAD Horizontal Resaw with Return;6" Wide x 12" high capacity Resaw. -- Standard spring blade tensioning system; 13'-2" x 1-1/4" x 0.035 Blade provides thin Kerf savings. -- Quick & easy blade height adjustments. -- 28" Dia. CNC machined, dynamically balanced, all steel band wheels, (4) bolt flange. -- Rough top feed belt combines with opposing side feed rolls and top hold downs. -- 20 HP High Efficiency, 3-Phase electric motor on each head. -- Variable feed speed from 20 to 120 FPM (6 to 36 MPM). -- Complete with: Return conveyor for resaw of wide width.
Equipment Location:MIDWEST
$7,500
Single Head BAKER "BPQ-0" ReSaw, 20 HP TEFC motor, 8" x 12" max. capacity. -- Gear driven feed from head motor, 0 - 120 FPM electronically controlled via frequency drive. -- Feed works with 6" wide rough top belt conveyor on self-centering rollers combined with holddown wheel. -- 28" Wheel dia., 0.035" x 1" x 13-1/6' blade size, 0.072" kerf, mechanical spring blade tensioning. -- BAKER's "Octaguide System" to reduce guide wear by up to (8) times as compared to conventional guide system.
Equipment Location:SOUTHEAST
$29,500
BAKER C 4-HEAD Horizontal Resaw with Return;6" Wide x 12" high capacity Resaw. -- Standard spring blade tensioning system; 13'-2" x 1-1/4" x 0.035 Blade provides thin Kerf savings. -- Quick & easy blade height adjustments. -- Wheels: 28" Dia. CNC machined, dynamically balanced, all steel band wheels, (4) bolt flange. -- Rough top feed belt combines with opposing side feed rolls and top hold downs. -- (4) 25 HP High Efficiency motors on each head. -- Variable feed speed from 20 to 120 FPM (6 to 36 MPM). -- Complete with: Return conveyor for resaw of wide width. -- Special Note: New Hub Bearings, New belts, New chain, Re-crowned all the feed wheels, New hood Guards. All new blade guide rollers, New blades etc,etc.RUN READY!!
Equipment Location:MIDWEST
$102,900
BALEMASTER EO-720 AUTO-TIE HORIZONTAL BALER -- 10" Cylinder -- Wide Chamber -- 50 HP Motor -- Feed Chute 60" L x 41-1/2" W -- Bale Size 30" H x 44"W x Variable Length -- Shear Blade / 4 Wire Tie -- Touch Screen Controls with Allen Bradley PLC -- Rough Top Conveyors Inclined; Lowe Horizontal and Feeds Incline Conveyor -- Loaded on your truck
Equipment Location:MIDWEST
$27,900
BALEMASTER 1772-AO HORIZONTAL CLOSED DOOR BALER -- (2) 6" Cylinders -- 25 HP Motor -- Feed Opening 60" L x 46 W -- Bale Size 72" L x 48" W x 36"H -- Number of ties per bale 5 -- Total weight 17,650 lbs -- Loaded on your truck
Equipment Location:MIDWEST
$45,000
BALEMASTER E-660 AUTO-TIE HORIZONTAL BALER -- Bale Size: 30”W x 36”H x Var L -- Feed Chute Cross Section: 27” W x 32” L -- Cylinder: 6” bore -- 25 HP motor -- PSI on Ram Face at Max. Operating Pressure of 3000PSI 85 -- Number of Bale Ties: 5 -- Air/Oil Cooler INCLUDED -- SPECIAL WORK TO UNIT; -- Bring the baler in to our shop -- Set it up -- Fill tank with hydraulic oil -- Hook it up to power -- Inspect -- Push the bales out -- Steam clean and prep for shipment -- Deliver on tarped flatbed to Spencer, Iowa -- Crew to unload and install baler (depending on application) -- Set up auto tie and align needles -- Start up and training if power and material is available
Equipment Location:MIDWEST
$70,500
BALEMASTER HD-60 CLOSED DOOR HORIZONTAL BALER -- 20 HP motor TEFC -- 8" Cylinder -- Bale size 48" x 30" x 60" -- Number of wire tie slots 7 -- Touch screen controls with Allen Bradley MicroLogix PLC -- Fused electrical disconnect, Nema 12 enclosure -- 22" x 22" Windowed feed chute door with control circuit interrupter. -- Low oil / hot sensor -- Full pen ram -- Full bale eject -- Replaceable shear blade
Equipment Location:MIDWEST
CDN$179,900
BALEMASTER 4500 SERIES, MODEL 11120 AUTO-TIE HORIZONTAL BALER -- Auto-tie model -- Touch screen / 15,518 hours -- 75 HP motor -- 10" Cylinder -- Feed opening 46" x 75" -- Bale size 40" x 48" x variable length -- Was doing OCC with 2,000-2,600 lbs bales -- Loaded on your truck
Equipment Location:EASTERN CDN
$39,990
BALEMASTER 46150G-10J4UYQJK4 AUTO-TIE HORIZONTAL BALER -- 150 HP Motor -- 10" Cylinder -- Feed opening 40-1/2" x 75" -- Fluffer Twin 10 HP Motor -- Conveyor not included -- Loaded on your truck
Equipment Location:MIDWEST
$54,900
BALEMASTER BB-3220T-6 AUTO-TIE HORIZONTAL BALER -- Bale Size: 30”W x 36”H x Var L -- Feed Chute: Cross Section 28” W x 32” L -- Cylinder: 6” bore (Rebuilt) -- 20 HP Motor -- No Load Strokes per Minute 2.9 PSI on Ram Face at Max. Operating Pressure of 3,000PSI 85 -- Number of Bale Ties: 4 -- A-B MicroLogix PLC -- Touch Screen Controls -- Loaded on your truck
Equipment Location:MIDWEST
Call
BARKER Boiler and Fuel System built & tested in 2011 as a pilot unit. Successful testing has been completed. This surplus equipment includes the following main features: -- Combustion Temp Capability- 2,000 deg.F.; Steam Flow 24,000 lbs/hr saturated; Steam Pressure 1,500 PSI @ 600 deg. F. -- Fuel Feed rate - 3,000 Lbs/hr at 1/4" biomass (5% moisture) -- Heat Input - 7,500 btu/Lbs HHV @ 22 mmbtu/hr. -- All equipment has less than 2,500 actual operating hours since installation.EQUIPMENT MAJOR COMPONENTS: Combustor, Cyclonic combustion technology, Refractory lined Heat Recovery. Steam Generator. Rotary Drum Dryer for Fuel drying - capable of 30% moisture reduction (at the above combustion parameters) and 1.5 tons per hour (installed as used equipment).BALANCE OF PLANT FUEL FEED SYSTEM: Live-bottom bin, Bunker, Feed conveyors, Wood hog, Vibrating screen, Drag and screw conveyors. Boiler water system - feed pump,water and steam piping Emissions Control: All required baghouses (SJVUAPCD) California permitted. -- Now REDUCED PRICE from $1.5 million !!
Equipment Location:WEST COAST
$3,695
BELFAB JNBM-OP Modular Dust Collection SystemPatented Modular Technology. Designed to collect dust particles ranging from coarse to fine. -- Compact, small footprint interior application design. -- 7.5 HP motor with 3,500 CFM. -- The filtration surface is composed of (1) 165 sq. ft. filtration module with (18) twill cloth filter tubes. -- Direct drive centrifugal fan assembly. -- Anti-spark cast aluminum impeller. -- Manual bag shaker.
Equipment Location:WESTERN CDN
$12,995
BELFAB - "NBM-OP3 15", ...Modular Dust Collection System.Patented Modular Technology, can be designed for current needs and easily upgraded as required; designed for interior use. -- Rated @ 5,000 CFM with: 10" Static pressure W.G.; 15 HP HUMMER blower at 1,800 RPM, 14" inlet, anti-spark steel impeller. -- (3) "NBM-OP" filter modules, each with (18) 7" x 60" Poly Twill cloth filter tubes, 495 sq. ft. total cloth area. Includes: -- Pneumatic Chip / Dust Transfer System w/ (3) hoppers and (1) 7.5 HP blower to blow debris outside to container. Unit can be fitted with adapters for use with plastic tilt trucks. -- Automatic shaker for filter to keep filter bags clean. -- Electrical controls including (3) starters, one for each blower and one for the shaker mechanism.
Equipment Location:MIDWEST
$3,995
BELFAB JNBM-OP Dust CollectorPatented Modular Technology. -- Designed to collect dust particles ranging from coarse to fine. -- Compact, small footprint interior application design. -- 7.5 HP motor with 3,500 CFM. -- The filtration surface is composed of (1) 165 sq. ft. filtration module with (18) twill cloth filter tubes. -- Direct drive centrifugal fan assembly. -- Anti-spark cast aluminum impeller. -- Manual bag shaker. -- Includes: Manual starter, factory installed with 5' cable for three phase.
Equipment Location:NORTHWEST
$3,995
BELFAB JNBM-OP Dust CollectorPatented Modular Technology. -- Designed to collect dust particles ranging from coarse to fine. -- Compact, small footprint interior application design. -- 7.5 HP motor with 3,500 CFM. -- The filtration surface is composed of (1) 165 sq. ft. filtration module with (18) twill cloth filter tubes. -- Direct drive centrifugal fan assembly. -- Anti-spark cast aluminum impeller. -- Manual bag shaker. -- Includes: Manual starter, factory installed with 5' cable for three phase.
Equipment Location:MTN/CENTRAL CDN
Call
BELFAB NBM 6-20/20 Modular Dust Collector;(6) Modules and Dust Transfer Hoppers with (2) 7.5 HP Material Transfer blower assemblies. -- Technology: Self-contained and fully enclosed with unique, patented, Heavy Duty construction designed for interior or exterior use. Trouble free shaker bag cleaning.Equipped/Specs: -- Each "NBM" filter module is fitted with (1) service door & (1) explosion door per NFPA safety regulations, and integrated compact hopper; rated @ 11,000 CFM with 10" static pressure w.g.; -- (108) Total filter tubes in (6) filter modules, each module with (18) 7" x 60" Poly Twill cloth filter tubes; 990 sq. ft. total cloth area, 11:1 air-to-cloth ratio. Supplied with: -- Bag shaking mechanism automatically activated upon shutdown. -- (2) Direct drive centrifugal fan assemblies with 20 HP TEFC Motors (run one or both blowers as needed) side mounted, both with anti-spark cast aluminum impellers. -- (2) 16" Dia. inlets and 17" outlet. Includes & Complete with: -- Chip and Dust Transfer System with (2) 7.5 HP Material Handling blowers, continuously discharges chips and dust for re-cycling or disposal. -- Electrical control panel with all pre-wired motor starters, adjustable timer, pilot lights, & shaker mechanism.
Equipment Location:ATLANTIC CDN
CDN$29,500
BM CONCEPTION DUST COLLECTOR MODEL 60 -- Pulse Jet model -- 60 HP motor -- Soft start and control -- 10 feet diameter -- 65 feet height -- 147 bags -- Spare impeller
Equipment Location:EASTERN CDN