49 Results Found for Sawmill Viewing 1 - 25 of 49 results

Cooper Machine MIT S.A. Vertical Band 1275

MIT has five models of their Vertical Band Resaw to cut varying widths and heights. The 1275 model uses a 6" band and has a 4'2" wheel. These resaws come with a line bar, variable hydraulic feed from zero (0) to two hundred and thirty (230) feet per minute, a live roller table with four (4) 6 ½ inch rollers, cartridge type pressure guides with the lower stationary, upper moveable, operator controlled, single or double hydraulic hauling and press roller drums, yoke and flywheel pistons of cast steel, air strain system with heavy duty air bag, using hydraulic hose for long lasting service and virtually no maintenance except for draining, electric motor activated system for raising and lowering flywheel, all systems are complete with valves, motors, cylinders, hoses, and controls, hydraulic system complete with tank, motor, pump, hoses, and valves, programmable measuring system using MUDATA microprocessor with ten position program and infinite variable parameters, and a main drive.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S.A. Horizontal Bands 700 Model

MIT makes four different models of the horizontal band. The smallest model is the 700 model. It has 28" diameter wheels and uses either a 1" or 2" band. It has one 20hp electrical motor on each head and can be used either 50 or 60htz. It also has a polychain belt drive and a 13’-0” infeed and outfeed metal tabletop chain conveyor.It uses pressure guides and can either have a manual saw set or a Mudata system can be added. Multiple heads available.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S. A. Center Split Resaw SCI-900

MIT has Two models of center split resaws to fit your needs. The SCI-900 model has 3 foot diameter fabricated solid steel wheels for 4 inch vertical band. Wheels will be flat ground unless otherwise specified. Has a high tension band with pneumatics systems. Includes a fixed pressure guide system. There are two modes where you can run it with a center split or off to one side. Manual setworks included (optional Mudata system available). Variable speed to 200 feet per minute. The principal motor is 30hp 50/60 htz and it comes complete with electrical panel.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S.A. Horizontal Bands 1000

MIT has four models of the horizontal band resaw. The 1000 model works well with cants and slabs. It has heads mounted on a reinforced frame, 40” (1000mm) diameter fabricated solid steel wheels for 2 or 4” bands. It has one 60hp electrical motor on each head either 50 or 60 htz. A variable speed drive for principle motor is included along with a polychain belt drive. Also includes a 13’-0” infeed and outfeed metal tabletop chain conveyor. Available with manual head adjustment or a Mudata programmable measuring system. We also include a Lubie lubrication system for ease of lubricating.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S.A. Horizontal Bands 1275 Model

MIT has four horizontal band resaw models. The 1275 model has 4’2” (1275 mm) diameter fabricated solid steel wheels for 6” or 8" bands. Designed and fabricated with a solid center to generate maximum airflow efficiency while still allowing optimum design strength. Wheels are stress relieved and balanced to ensure smooth and vibration free operation. All bearings are first line quality. Air strain system is supplied with heavy-duty air bag using hydraulic hose for long lasting service and virtually no maintenance except for draining. Pneumatic system for flywheel movement to change blade. System allows adequate movement for extension and contraction for blade removal. Tracking and final adjustment are easily made. 75hp electrical motor on the head either 50 or 60 htz. Mudata Model Pos Div 114 for one head is included. 13’-0” (3.96m) in feed and out feed metal tabletop chain conveyor and wide motorized pressure rollers on front and back of the blades.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S.A. Horizontal Bands 1400 Model Single

MIT has four models of Horizontal Band Resaws. The largest is the 1400 model. It comes as a single head, a double head in tandem (back to back) or as an over/under band. It has 4’7” (1400mm) diameter fabricated solid steel wheels for 8” bands. Designed and fabricated with a solid center to generate maximum airflow efficiency while still allowing optimum design strength. Wheels are stress relieved and balanced to ensure smooth and vibration free operation. All bearings are first line quality. Air strain system is supplied with heavy-duty air bag using hydraulic hose for long lasting service and virtually no maintenance except for draining. Pneumatic system for flywheel movement to change blade. System allows adequate movement for extension and contraction for blade removal. Tracking and final adjustment are easily made. 100hp electrical motor on the head either 50 or 60 htz. Frame configurations have been engineered and designed from structural steel tubing and steel plate.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S. A. Center Split Resaw SCI-1400 Model

The SCI-1400 is MIT's largest center split resaw. It comes with 55" diameter fabricated solid steel wheels for either 6 or 8" bands. Variable speed hydraulics feed from 0 to 227 feet per minute. Fixed pressure guides. Electric motor for quick change of saw. High tension band with pneumatic systems. Air strain system with air bags. Includes hydraulic tank, pump, electrical motor, valves etc. With 75hp 50/60 htz electric motor and complete electrical panels. This machine can either center split or offset cut. Now includes MIT PLC and touch screen.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT S.A. Vertical Band 1500 Model

MIT Vertical Resaw Model 1500 has a 59 inch diameter fabricated steel wheels for 8 or 10” bands. Designed and fabricated with a solid center to generate maximum airflow efficiency while still allowing optimum design strength. Flat ground face (unless otherwise specified). Wheels are stress relieved and balanced to insure smooth and vibration free operation. All bearings are first line; flywheel bearings are double taper-lock roller type. The air strain system has air bags for long lasting service and virtually no maintenance except for draining. Line bar comes extra-long and extra high. The resaw also has double parallel hydraulic arms and a variable speed hydraulic feed from 0 to 230fpm. It is driven by 100hp motors 50 or 60htz. It also comes with a Mudata programmable measuring system and a live roller infeed table (7” in diameter). A hydraulic tank and power system comes complete with 7.5hp electric motor for quick change of saws. It comes on a frame of reinforced steel.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine MIT 1275 Center Split Resaw

The SCI-1275 is MIT's largest center split resaw. It comes with 55" diameter fabricated solid steel wheels for either 6 or 8" bands. Variable speed hydraulics feed from 0 to 227 feet per minute. Fixed pressure guides. Electric motor for quick change of saw. High tension band with pneumatic systems. Air strain system with air bags. Includes hydraulic tank, pump, electrical motor, valves etc. With 75hp 50/60 htz electric motor and complete electrical panels. This machine can either center split or offset cut. Now includes MIT PLC and touch screen.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Chipper

Cooper Machine is a sales representative for Precision Husky Waste Systems. We are able to provide any Precision Husky equipment to complement the Cooper Machine equipment you purchase including screens, chippers and vibrating conveyors. The canted side spout design and the position of the knife causes a smooth slicing action. The attack angle of the knife gives a gentle lift to the slab as the knife passes the center line and begins the upward swing turning the slab counterclockwise. The spout has a flat bottom and canted side to give 25 % more anvil contact, preventing slapping and wood turning in the wrong direction. Horizontal and vertical anvils give additional life, requiring less maintenance. Both anvils are hard surfaced with Colmonoy with a hardness of 62 - 65, Rockwell C scale. With a four sided replaceable anvil, maintenance and time are saved. Less horsepower is needed with Precision's smoother action. Options for 38" [96cm], 48" [122cm], 58" [147cm] and 66" [168cm]
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Heavy Duty Debarker

Now introducing the Cooper Stave Debarker. Debark logs 18” to 46” long and 8” to 34” in diamter. Comes with infeed plate slides, 48” long Stringer Bark King Debarker Head with 2 15/16” shaft and bearings, 125hp 1200RPM drive motor and drive, depth gauge plates in head, eyes for opening and closing log holding arm position, 1” AR log cage arm assembly with 3 7/16” Can Am pivot shaft bearings, 6”@20 beam, Six 21”OD, 1” AR Bull Wheels for Log Rotating and Removal. Debarked logs are dropped out below. You can open the cage and pass logs through if hog is down. Debarker will fit in the same spot as existing debarker. Comes with VFD and Soft Starter, Control Panel with Computer/PLC and Software to Auto Run Debarker. Cut down on your labor! One person can run the Stave Cutup System and Debarker. If you have short pallet logs you want debarked, this machine can handle that too!
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Board Edger

Now offering an all electric version of our popular two saw board edger (no hydraulics!) Cooper Machine manufactures a 2, 3 or 4 saw edger that is able to edge cants, boards or slabs. The most popular 6” edger comes with two movable saws to handle cants, boards or slabs from 3 inch to 18 inch wide (but custom configurations available). The operator uses the console to select the sawing size and then an optional set of laser lights follows the saw and shines on the wood to assist the operator in choosing the right sawing solution. The edger is available with an optional infeed rollcase with a set of jump chains to assist the operator in positioning the larger material onto the edger. The material can either be manually pushed onto the edger or this can be automated. On both options, multiple hold-downs pin the material to the rollers for better accuracy.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Drop Saw

Cooper Machine offers the drop saw trimmer as a better way for you to trim your boards, cants and cross-ties. This automated machine provides a precision cut and includes start/stop functions, as well as a manual override for length and adjustments. Hardwood and softwood can be set with pre-set speeds. The Drop Saw Trimmer can trim up to 24’ of boards and cants. Optional infeed rollcase with cant turner is available.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Top Arbor Two or Three Saw

The top arbor two or three saw trimmer trims three sided cants or slabs. This is a great option behind the Yield Champ to edge the cants or three sided pieces.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Movable Head

The bottom arbor trimmer is available with three to six heads. All of the heads are movable and it can trim up to a 10x10 cant, board, or three sided piece. Comes with a 30” saws and each saw has 20hp motor.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Stave Equalizer

Cooper Machine offers a Stave Equalizer Two Saw Top Arbor Trimmer. This machine feeds from the side and as soon as it gets in it even ends the board and lugs it through the trimmer. This machine manually adjusts from 30 inches up to 48 inches and trims boards from 3/4 inches up to 2 inches thick. Each arbor is mounted on 2" chrome slides and bearings with hand crank sets. The rollcase is a side feed 8', with 4' in the trimmer and 4' out for hand feeding with a 1hp drive. Four sets of board hold-downs over the lug feed. Comes with two 22" diameter saw blades, two 10hp saw arbor motors, 81x lug chain feed, 2hp electric lug chain feed, a starter panel with starters for the machine and a control panel with E-stop, motor start/stop buttons, lug start/stop eyes and a PLC for lug feed control. Frame is 6 @ 20 beam. Built heavier than standard stave equipment.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Stick Gang Rip Saw

These small gangs can cut battons, kiln sticks and strips with ease. Heavy fabricated steel frame with guards. Includes an electrical panel and VFD feed drive. Available with different configurations, so call to find the solution that works for your application.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Conventional Overhead

End-dogging log mills have been a Cooper Machine specialty for 50 years, which is why Cooper is known for being the best Scragg on the market. Cooper Machine offers versions of the Overhead Scragg that are designed to handle logs as small as 3 feet up to 20 feet long, depending on the customer’s specifications. These machines are designed and built to run a long time (with some still in operation over 30 + years) with little maintenance, and with just one man needed to operate the machine. We do this to save you money in the long run. The Overhead Scragg is available with 48” or 56” diameter circle saws. Also available with a Twin Band (see Twin Band Overhead). These machines are available with several options for setworks including: manual setworks, Cooper’s own ultrasonic measuring system, Cooper X/Y scanning or 3D scanning. The Overhead Scragg is available with several upgrades available including three or four saw vertical edgers, graphic display and rear dog lift. Also now available with chipping heads.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Skewing Overhead

The Skewing Overhead takes the best of the Standard Overhead and adds some new features that increases both yield and production over the Standard Overhead. Different variations of this machine can handle logs as small as 3 feet up to 20 feet long, depending on the customer’s specifications. Like our Standard Overheads, these machines are designed and built to run a long time with little maintenance, and with just one man needed to operate the machine. We do this to save you money. This machine comes standard with skewing log turners that are able to skew up to 3" left/right. This allows the Overhead to create two equal faces to increase yield on marginal logs and reduce the amount of boards to be edged. The modification to a rear pivot dog lift allows for increased production.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Conventional Sharp Chain

Cooper Machine offers several versions of the Sharp Chain Scragg. The Standard Sharp Chain uses 100 roller chain with drags to run inside 3 x 4 x 3/8 tubing with 3/8 x 1 AR wear strips. It is built to accommodate smaller diameter (from 3 ½” to 12”) low grade logs with standard feed speeds from 40” to 20’ long. The Sharp Chain Scragg is also available with manual setworks, the Cooper profiling and measuring system or Lewis Controls 3D scanning. This equipment is manufactured from heavy duty steel and parts to create a long lasting machine with low maintenance costs.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Twin Band Overhead

Twin Bands ranging in sizes 8" up to 12" are available with either the Skewing Overhead or the Standard Overhead. Cooper Machine sells MIT S.A. band saws or we can use the customer's choice. Models are available to cut from 36” up to 20’ in length. This machine is also available with Chipping Heads and can be run with Cooper controls or 3D Scanning (Lewis Controls or your choice).
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Yield Champ

The Yield Champ Scragg is a combination Sharp Chain Scragg and Edger for further processing the cant. It utilitizes an optimized log turner and sharp chain feed system. A great benefit of the Yield champ is it requires minimum man power (only one man is needed to operate both the Sharp Chain Scragg and Edger). Once the log is through the 44”, 48” or 56” diameter saws (depending the customer’s requirements), the cant is rotated 90 degrees and then fed into a second saw(s). There it is cut into a three or four sided cant or into two cants and two slabs with the three saw option. This mill is available with Cooper computer controlled saw setworks (which provides precise cutting of cants) as well as several options depending on customer needs including an infeed deck and slab recovery system. All of this equipment is manufactured from heavy duty steel and parts to create a long lasting machine with low maintenance costs.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Precision Sharp Chain

Cooper Machine also offers a high quality Precision Sharp Chain that comes with a 140 roller chain t-bar rail sharp chain system for faster production. It has a thumper to drive the log down on the chain. The Precision Sharp Chain Scragg is also available with manual setworks, the Cooper profiling and measuring system or 3D scanning. All of this equipment is manufactured from heavy duty steel and parts to create a long lasting machine with low maintenance costs. The Sharp Chain is also available with MIT (or customer's choice) band saws behind it to split cants into (2) three-sided pieces for maximum yield. MIT S.A. horizontal bands are available with 4,5, or 6” bands for this purpose.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Twin Band Skewing Overhead with Chipping Heads

We took our high production Skewing Overhead and MIT 10 inch Band Saw and added Key Knife Chipping Heads and made a masterpiece. This machine can cut hardwoods or softwoods from 5" up to 28" in diameter. Multiple length options are available. This machine has our skewing center system with independent log positioners, ultrasonic sensors for diameter readings of the logs for autoset with manual override (or 3D scanning available), and skewing log turners. There are two wide cant supports (one before and one after the chipping heads). Six head key knife chipping heads with 150hp drive motors and a polychain belt drive. A MIT Twin Band (or customer preference) with 63 inch diameter wheels and 10 inch bands were used on this machine but different size bands and wheels are available. Outfeed consists of 8 inch center beam cant guide with two 22 inch wide belt conveyors. Comes with hydraulics, power unit, a 8 x 8 foot cab, four camera color monitoring system, computer and graphic display.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885

Cooper Machine Tandem Scragg Saw with Inline Chop Saw

Cooper Tandem Scragg is great for smaller diameter logs when you want production without a lot of employees. The Tandem Scragg is comprised of two saws, 48 inch Saw 1 and 36 inch Saw 2 (custom configurations available). Thinnest material/thickest material saw 1 can cut is 3” – 12”. Ultrasonic sensors for diameter reading of logs for first saw autoset with manual operator override, auto band saw set to make four sided cants. Comes with a Generation 3 Precision Chain Feed using 140 roller chain and hardened t-rail track, 20hp variable speed electric chain drive with VFD climate controlled cab, and four camera color monitoring system. Saw 2 has a minimum 3” saw set. Saw two comes with two 75hp motors and polychain belt drives, 2” induction hardened chrome shafts and linear slide bearings, and temposonic cylinders with sensors and helper cylinders for husk frame autoset (and manual override). The outfeed consists of 6" cant/slab separation wings behind saw, four sets of spring loaded hold-on wings and an 8” H-beam common frame. This machine can come in a system and include an inline infeed with chop saw, slat tables and an Outfeed Rollcase. For more information or to design the system to fit your needs, give us a call.
Cooper Machine Company, Inc.

Wadley,GA
478-252-5885