Woodworking Equipment For Sale

2-Machine System consisting of BALESTRINI "PICO" Round End Tenoner & BALESTRINI "MICRO.N" Slot MortiserSpecifications -- "PICO" Round End Tenoner: Left & right "twin" tilting tables (one table is always in the cutting position); 14" x 9" tables tilt 0ø - 20ø, both table fences with pin stops for indexing stile and rail doors. -- Fences swivel up to 45ø, each table with vertical pneumatic holddown; 4 HP cutter block motor, 1 HP cutter block rotation motor, 9,000 RPM spindle speed. -- Capacity: 3-15/16" (100 mm) Max. tenon length, 1-3/16" (30 mm) max. thickness, and 1-31/32" (50 mm) max. depth. - Hourly production rate of (600 - 700) tenons."MICRON" Slot Mortiser: Dual spindle system, (1) each side with tables and overhead holddown, 3 HP - 9,000 RPM spindles, (60 - 350) oscillations/Min, 18 mm collet dia. -- Capacity: 4-23/32" (120 mm) Max. length of slot, 3-1/8" (80 mm) max. slot depth, 1-3/16" (30 mm) max. slot thickness. - Hourly production rate of (500 - 800) slots.Note --The PICO has a timing issue and may just need to be adjusted.

Barberan UV Oven

Barr Mullin Wondersaw Optimizer with Computerized Laser Controls Tichniess: Up to 3" Width: 31" Min cut: 4" Feed height: 34-1/2" Floor Space: Apprx 21' x 15' 480 volt

SALE PENDING Baxter Whitney "No. 32A" Planer - 30" Machine is in full working order. We will provide services for power disconnect as well as loading onto any transport vehicle provided.- Call 800-459-2148 for more info.

Baxter Whitney & Sons Planer model 32-A manufactured in mid 1940s. This planer was taken out of service in good working order about 8 years ago. I have not used it. There is one pulley that has a broken edge as seen in photo 9319. This was broken in transit and should not affect its function . This planer has a 15 hp, 3 ph main motor with a 3 hp feed motor. Dust hood included. It will need to be picked up with a roll body truck. It comes with the knife sharpener and the sharpener box. Call 800-459-2148 for more info.

Planer cast, has all belts, 8"x 24", tight an in good shape, Call 606-473-0085 for more info.

BECKER KVT 3.100 3.6 Kw (5 HP) Vacuum pump:Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 69 CFM and 100 cm/Hr with max. 27"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blowoff valve/silencer. -- Complete WithInlet vacuum air filter system.

BECKER VTLF 2.400 Vacuum pump:Seller states the pump was only turned on a few times15 HP Oil-less (Dry) Rotary Vane vacuum pump system, rated @ 270 CFM open flow, max. 23.6" Hg; heavy duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance free with built-in carbon vanes and built-in suction filters. Complete with: Vacuum regulating valve, secondary suction for additional cooling, blow-off valve/silencer, 4" BSP x 4" NPT Nipple; coupled to a 886 RPM TEFC motor.

Becker VTLF 250 Vacuum Pump: 6.6 kW (8.8 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor. -- Also available at extra cost! -- $2,800 for the ROW 25 HP phase converter -- $1,900 for the electrical control panels

Becker VTLF 250 Vacuum Pump: 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TEFC; 400/480V, 1,160 RPM motor

Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

Biesse Akron 1440 PUR Return conveyor available - demo unit!

Biesse Akron 245 Edgebander System is still under power until approx mid-October 2024. Touch PLC will need to be replaced. Everything else is working good on the machine. Owner has had it serviced by Biesse.

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE - AKRON 855, ...Computer Controlled Production Edgebander.Features & Main Specifications: -- Computer-controlled interface for workstations with: Servos and pneumatic positioning devices. -- Programmable selections for "1-touch" changeover between edgebanding types and thicknesses. -- Edgebanding thickness: 0.4 - 19 mm Capacity. -- Min. panel: Width 85 mm & length 140 mm; thickness of 10 - 50 mm. -- Feed speed variable from 10 - 20 MPM, 3 HP feed drive.Frontend Equipped with: -- Premilling Unit with: (4) Positions for automatic changeover between premill settings, NC controlled. -- Strip & Coil Edge magazine: Automatic, "HD" shear-type guillotine. -- Top Pressure Beam: On-screen adjustable for height positioning. -- Hot-Melt Glue System: 12 Min heat up time, Teflon® coated gluepot; digital thermostats with automatic kick-down when machine is in idle mode. -- Side Pressure Section with: (1) Large dia. "non-stick" coated drive roller; (5) Teflon® plated idle rollers with Servo positioning, and NC controlled material thickness adjustment. Workstations: -- End Trimming Unit: Front & Rear (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 15° on horizontal. plane, NC controlled. -- Flush Trimming Unit: Top & Bottom with "Quick Change" motors, 1.0 HP - 12,000 RPM motors; digital readouts for easy setup. - 2-Position NC controlled. -- Flush/Bevel/Radius Trimming Unit: Multiuse top & bottom, 2-motor (0.3 HP - 12,000 RPM). Servo driven positioning of motors for different edge trimming setups. NC Controlled adjustment between profiles and positions. -- Corner Rounding Unit: 4-Motor (0.3 HP - 12,000 RPM motors) for trimming leading & trailing upper & lower edge/corners with "Fast Position"; can be used as a 2nd Top & Bottom fine trimmer, as well. -- Profile Scraping Unit: Top & Bottom for 2 mm or 3 mm thick PVC banding; digitals for horiz. adjustments. -- Flat Scraping Unit: Top & Bottom for glue and fine panel scraping. -- Buffing Unit: Top & Bottom (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. -- Hot Air Blower Unit: Top & Bottom edge reactivation station (2,000 Watt), hot air blowers with temperature adjustment. Complete with: -- Programmable processor for workstations & feed speed. -- Insulated sound enclosure over all trim stations with: Triple split dust & safety hood enclosure, industrial lights, and viewing windows. -- Extendable side panel support rail. -- 12 KVA - 240 Hz Digital frequency inverters.Includes: -- Used tooling on all workstations. -- Extra set of diamond tooling for premill unit. -- (1) Premill motor. -- NOTE: Chain pads have been replaced (2) years ago

BIESSE ROVER 18 CNC MACHINING CENTER: -- Specifications: Working capacity: "X" Axis 91" (2,310 mm); "Y" axis 24-3/4" (928 mm); "Z" axis stroke is 3-1/2" (90 mm); max material thickness 2-1/2" (65 mm). -- Worktable(6) Stationary Panel Supports with: (2) Vacuum cups each. -- Positioning Speed "X" & "Y" Axis 328 FPM (100 MPM); "Z" axis 27 FPM (90 MPM). -- Boring Unit2.3 HP Motor - 4,000 RPM with: (12) Independent Vertical spindles with (7) spindles in "X" axis & (5) spindles in "Y" axis; all spacing on 32 mm centers.(4) Horizontal spindles with: (2 + 2) in "X" axis for boring top & bottom edges of panels.(1) "X" Axis grooving saw for max 120 mm (4.7") dia. blade. -- Machining(1) 10 HP (7.5 kW) Router; variable speed from 12,000 - 18,000 RPM for RH or LH rotation with 7.5 kW inverter. -- Operator & Machine Control:CNI "NC 481" CNC 3-Axis Controller; built-in 9" amber CRT; 32 KB memory; 3-1/2" floppy disk drive.Tool correction, circular & helical interpolation, feed speed override, user-friendly programming, and background editing. -- Complete with: (1) 40 cbm/Hr Vacuum Pump; 20 KVA Stabilized autotransformer, side & rear safety fencing, safety photocell barrier. -- Actual Model is: BIESSE - ROVER 18.

BIESSE - JADE 240, ...Edgebander w/Premill & Corner Rounding -- Specifications: Edgebanding thickness: 0.4 - 8 mm (0.01" - 0.31"); Min. panel width 85 mm (3-1/2"); min. length 150 mm (5.9"); max. panel thickness 10 - 60 mm (0.39 - 2.36"). -- Premill Unit: (2) 1.8 kW (2.4 HP) - 12,000 RPM Motors; "AUTO-SET" device ensures optimum positioning of the cutters according to the thickness of the panel being machined; numerical readout; pneumatic exclusion when not needed. Workstations: -- End Trimming: Front & rear end trims: 0.8 kW (1.0 HP) - 12,000 RPM Motors; motors travel on 45° slides and pneumatic tilt 0° - 15° from the Control Panel. -- Flush/Bevel Trimming Unit: Top & bottom flush or bevel trims with: "Quick Change" Motors; 0.65 kW (0.8 HP) - 12,000 RPM motors; digital readouts for easy setup. -- Corner Rounding Unit: (2) Motors, 0.65 kW (0.8 HP) - 12,000 RPM for trimming leading & trailing upper & lower edge/corners with 2-position pneumatic set-up for corner rounding. -- Edge Scraping Unit: Finishing unit to eliminate previous machining imperfections; pneumatic exclusion from the machine control. -- Glue Scraping Unit:Top & Bottom scrapers for 3 mm thick PVC banding. -- Buffing Station: Top & Bottom.Operator & Machine Control: -- BIESSE "Smart Touch 7" + Windows Operating System: User-friendly touchscreen Control Panel for workstations; rotating Operator Control Panel w/keypad and LCD readout.Graphic 7" display touchscreen; high-resolution screen for defined and intuitive images and text; integrated 4 GB hard disk for filing media files and the programs back up.USB Port for managing in a simple and efficient way multimedia files, programs, and updates; Ethernet port for connecting the machine to the net.Complete with: -- Top pressure beam & motorized feed track with "anti-slip" "Quick Change" snap on 80 mm wide x 60 mm long rubber pads; low friction nylon graphite self-lubricating chain pads. -- Sound Enclosure & Panel Support: Overall trimming stations; industrial lights and viewing windows; extendable side panel support rail. -- Fixed feed speed at 39 FPM (12 MPM); 3 HP feed drive.Options include: -- Anti-Adhesive Unit:The unit applies an anti-adhesive liquid on the Top & Bottom surface of the panel. It is positioned before the Premilling Unit.The anti-adhesive liquid is applied with precision by means of injectors controlled by the machine control. -- Nesting Package:Allows trimming of pre-machined panels. -- Transformer:230 Volt auto-transformer. -- Actual Model is BIESSE JADE 240

Biesse Levia 310-1350 Sander

BIESSE LEVIA 320-1100 Wide Belt Sander, (2) Heads43" Width cap., Drum, Combination HeadHead Configuration:1st Head: Contact spiral grooved roll, 6" Dia., 30 HP motor.2nd Head: Combination head with a spiral grooved rubber-covered contact roll, 7-1/2" dia. 45 Shore covering, segmented platen computer controlled with air segments, 24 HP motor.Specifications: -- 43" X 74" Abrasive belts. -- Electronic abrasive belt tracking. -- All contact rolls with pneumatic seclusion, heads with air-jet abrasive belt cleaners. -- Output control of sectional platen. -- Conveyor belt feed, 11 - 66 FPM variable feed speed; Automatic conveyor belt tracking. -- 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout.Equipped with & Features: -- Infeed and outfeed shoes or rubber-covered holddown rolls --Infeed panel "over-thickness" sensor. --Auto calibration, digital height read out -- Easy Quick grit selection. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop. -- 3-Roll infeed extension and motor load metersNOTE: Some spec's may need to be verified

BIESSE - ARTECH LEVIA 330, ...3-Head Wide Belt Sander43" Width cap. Drum, Drum, and Combination Head.Head Configuration: -- 1st Head: Rubber covered Contact Roll, 6" dia., 25 HP motor. -- 2nd Head: Steel Contact Roll, 6" dia., 25 HP motor. -- 3rd Head: Combination head with a rubber-covered Contact Roll and Finishing Platen.NOTE: There are (2) 25 HP motors; one drives the 1st head and the 2nd drives the other (2) heads.Specifications: -- 44" x 85" Abrasive belts, electronic abrasive belt tracking; all contact rolls with pneumatic seclusion; Head #3 with air belt cleaner. -- EASY PRO "2000 C" Processor with (200) programs, touchscreen for control of Sander functions, thickness opening, feed speed, sequential startup, contact roll seclusion, and abrasive belt cleaner. -- Conveyor belt feed, 11 - 66 FPM variable feed speed, 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout; automatic part thickness setup.Equipped with & Features; -- Automatic conveyor belt tracking. -- Infeed & outfeed shoes or rubber-covered holddown rolls, infeed panel "over thickness" sensor. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop, 3-roll infeed extension, and motor load meter.