Sanders For Sale

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

6" Wide x 108" long belt (non-oscillating), 6" x 40" graphite covered platen, 1.5 HP motor w/magnetic switch, 6" dia. drive pulley, 7-3/4" x 37" front table & end table for radius work both w/approx. 6" vertical adjustment. -- Features: Industrial laminated tables, fabricated steel base, swing-away type safety dust hood, rigid tracking.

EXTREMA ESO-108.1 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel -- 6" x 40" Graphite covered platen. -- 1-1/2 HP Single-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port. -- CFM Requirements: 400. -- Weight: 425 Lbs.

EXTREMA ESO-108.3 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel. -- 6" x 40" Graphite covered platen. -- 2 HP Three-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Sanding wheel shaper for the production of profiles on the sanding wheels. -- Template carrier holds metal or plexiglass template (same as can be used on the moulder knives). -- Spindle length 5" with 1" diameter arbor for wheel support. Handles 8" diameter wheels (3) included with the machine. -- X and Y axis on dovetail slide with lineal bearing support for smooth movement during the wheel grinding. Pneumatic clamping on grinding wheels. Depth of grinding 1.5" for raised panel. -- Tilt capabilities from 0 to + 30°. -- Grinds all types of varda wheels on 1 HP motor with speed of 1,750 RPM. --You can customize this machine to you needs.

G & P - EPN, ... Pump Sander (Double-Sided), Double-end direct-drive pneumatic Drum Sander.2 HP Motor - 3,600 RPM motor speed.(2) 1-1/4" Dia. x 10" long shafts.

GRAINMATIC - CP-960, ...2-Head Wide Belt Sander42" Width cap.; Drum, Platen.Head Configuration:1st Head: Spiral rubber covered contact roll, 7-7/8" dia., 20 HP motor.2nd Head: Combination Head, spiral rubber contact roll, and finishing platen; 15 HP motor.Specifications: -- 36" W x 75" L abrasive belts with air jet tracking. -- Motorized part thickness adjustment with keypad entry and LED readout; 0" - 7" opening. -- Infeed & outfeed spring loaded rubber covered holddown rolls. -- Feed Motor: 3.5 HP -- Variable feed speed: 15 - 60 FPM.Equipped with & Features: -- Infeed emergency stop bar. -- Disc brakes on sanding head motors. --12" Infeed load area. --Volt meters on sanding head motors.NOTE: Some specs need to be verified.

GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),

GRIZZLY H2934 2-HEAD WIDE BELT SANDER2-Head Wide Belt Sander, 36-1/2" width cap. -- Head configuration: - 1st Head: Rubber covered contact drum; 2nd Head: Combination head with rubber covered contact drum and adjustable platen; Abrasive belt size 37" x 60". -- 0" to 6" Thickness cap., LED digital depth encoder; 14" min. board length and 12" infeed conveyor. -- 1st Abrasive belt surface speed of 3,543 SFPM; 2nd abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP - 50/25 Amp Sanding motor; 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor. -- Complete with: Rubber covered holddown rolls, adjustable felt platen, Amp/load meter, and disc brake for emergency stop.

GRIZZLY GO447 37" Dual Head Wide Belt Sander.37" Width cap. Drum, combination HeadHead Configuration1st Head: Contact Drum2nd Head : Combination Head. Rubber covered drive roll and adjustable platen; sanding belt size 37"" x 75"".Specifications -- 6" Thickness cap., LED digital depth encoder; -- 14" min. board length and 12" infeed conveyor. -- Min board thickness 1/4" -- 1st Head Abrasive belt surface speed of 3,543 SFPM; -- 2nd Head abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP Motor driving both heads -- 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor.

HALSTY 136 WIDE BELT SANDER1-Head Sander with 36" width cap. and 6" thickness cap. -- Combination sanding head with 5-1/4" dia. contact roll, 2-1/2" wide polishing platen; 20 HP 3-Ph motor. 37" x 75" Abrasive belt, electronic tracking. -- Variable feed drive for conveyor belt with speeds of 0 - 18 FPM, 2" dia. infeed & outfeed rubber covered holddown rolls. -- 0" - 6" Thickness cap. with motorized adjustment via (4) 1" Acme thread jackscrews.

3 Head - 3 Phase - Mfg Year: 2011 - Three head sander - 15 H.P. Cross Belt - Variable Speed, Segmented Platen - 15 H.P. Combi Head Roller, Segmented Platen Variable Speed - 15 H.P. Plate Variable Speed - Segmented Platen - Motorized opening

---In Auction---NO RESERVE---Good Condition--- HEESSEMANN DBV 1 2,300 mm (90.55") 2-Head Cross Belt Automatic Stroke Sander Specifications: - Sanding length 2,300 mm (90.55"). - Sanding Belt size 150 x 8,500 mm (5.91" x 334.65"), Pressure belt length 6,750 mm (265.75"), V-Belt size 10 x 900 mm (0.39" x 3.43"). - Max. thickness 8". - Sanding belt speed 82 FPS. - Feed speeds 9 - 50 FPM. Equipped with: - (1) Rough sanding & (1) Fine sanding cross belt heads, with Limit switch-controlled pneumatic pressure plates with Timer, Dubbing control on fence side, Adjustable dubbing unit on right side, & 25 HP Motor. - 90” W x 5-1/2’ L Conveyorized feed table, with Multiple 5" W conveyor belts, Automatic tracking, & Motorized thickness adjustment. - Overhead hold-down rollers. Complete with: - 4" W Brush belt brush-off device. - Dimensions of Control Console: 40" x 21" x 56" H Details, Photos, Videos, Bidding: https://exfactoryauctions.com/Detail/SS-230669/event/A051324$1

NOTE: Wide Belt Sander was completely rebuilt for $68,000 in 2019. 53" 4-Head Wide Belt Sander Head Configuration: 1st Head: Spiral rubber contact roll, 45 kW, 460 V; 2nd Head: Spiral rubber contact roll, 44 kW, 420/480 V; 3rd Head: Spiral rubber contact roll, 37 kW, 460 V; 4th Head: Platen design with (2) Smooth steel rollers; Final Station: Rotating air-jet blow-off; 12" Load space, Sensing, Abrasive belt size 1,400 x 3,250 mm (55.12" x 127.95"), T.B. WOODS "E-TRAC WF-2" Sensor-less vector drive for variable sanding head speed Vacuum feed mat, Adjustable fence, VACON Variable speed drive for feed speed, 8.6 kW, 254-277/440-480 V, Electronic belt tracking & Pneumatic motorized thickness control, Approximately 2 HP, 230/460 V HEESEMANN Swivel-mounted touchscreen control Overall dimensions: 164" x 92" x 112" H, Weight: 11,000 kg (24,250 Lbs.) NOTE: Machine is currently in storage.

HEESEMANN MFA-6 Wide Belt Sander with (3) Heads and a Cleaning Brush.Basic Working Capacity: Max. working width is 1,350 mm (53"), thickness opening min./max. is 3 mm - 150 mm (0.118" - 6.0"). - Conveyor belt speed variable from 5 - 15 MPM (16 - 49 FPM); constant pass height of 880 mm (34.65").Features: -- Head Configuration: (2) Steel contact drum heads, (2) "CSD" controlled contact platens, and (1) rotary cleaning brush. -- Belt Handling: Broken belt monitor and automatic infrared belt tracking; intermittent pneumatic belt cleaning device, belt access on the left-hand side. -- Conveyor Belt: High powered vacuum holddown by 8.6 kW (11.5 HP) fan drive motor, automatic vacuum monitoring system. Variable speed by inverter from 5 - 15 MPM (16 - 49 FPM). -- CSD-32 System: Heads #3 & #4 are equipped with HEESEMANN's Patented "Segmented Pad System", Computer Selective Pressure Control from 0 - 150%, precise surface & edge pressure control, edge pressure independent of surface; 2 mm thickness compensation - zero maintenance with sealed enclosure.Sanding Head Configuration: -- 1st Head: Steel Contact Roll, 8" dia., 25.3 kW (34 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 2nd Head: Steel Contact Roll, 8" dia., 17.5 kW (24 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 3rd Head: Sanding Platen, electronically controlled pressure segments to conform to panel size, 17.5 kW (24 HP) motor; sanding belt size is 2,150 mm x 1,400 mm (85" x 55"), belt speed of 18 MPS (60 FPS); equipped with belt motor brake.. -- Cleaning Brush: Outfeed Rotary Panel Cleaning bristle brush, 120 mm (4-3/4) dia., 0.9 kW (1.2 HP) motor, and holddown roller. -- Includes: Outfeed conveyor table, 48" width x 80" length. Large batch of sanding belts.Controls: -- LCD Operating Panel with: Touch-screen and graphical display, (20) memory addresses for sanding head selection, thickness opening, conveyor feed speed, 1-button sequenced starting of sanding motors, and tracking of sanding belt usage. -- Operating Requirements: Electrical is 151 Amps @ 460 Volt; Dust Extraction is 5,800 CFM @ 3" static pressure. Machine weight approx. 7,000 kG (15,500 Lbs). -- Complete With: Extended infeed table with (2) idle rollers, interior lights, emergency and oversize part thickness safety bar, and Manual.

HEESEMANN MFA-8 D Wide Belt Sander (4) Heads; 53" Width cap. Veneer/ Sealer Sanding Wide Belt.Great Lacquer/Sealer sander with: (2) Segmented polishing platen, (2) Orbital heads, (1) De-nibbing/Polishing brush.Head Configuration: Head 1: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 2: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 3: Orbital head with composite/dense fiber loading; 5HP motorHead 4: Orbital head with composite/dense fiber loading: 5HP motor(1) Brush Type head for de- nibbing and polishingSpecifications: -- LCD monitor with graphic display and key pad entry, 20 program capacity, -- Pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required.Equipped with & Features -- Air blast abrasive belt cleaner on heads 1 & 2. -- Variable feed speed from 10 to 49 FPM via 2 HP feed drive. -- Motorized thickness opening 1/4" to 3-5/32" max. -- Rubber covered Infeed and out feed holddown rolls.

Heeseman LSM8 Wide Belt Sander